Position, Velocity, and Acceleration

The slope of position is velocity, the slope of velocity is acceleration, and areas run the chain backward.

Before this Lesson

A switching locomotive shoves a railcar back and forth along a straight yard track. Nobody wrote down where the car went. All that survives is a chart of its velocity against time. That one line is enough: it tells you how hard the car accelerated, when it turned around, where it ended up, and how far it rolled in all.

Where it is, and how far it went

Motion along a straight line takes just one number to describe: where the body is. Pick a zero point, pick which way counts as positive, and call the reading ss, the position. Every problem in this topic starts with that choice. Once it's made, signs carry direction, so a negative velocity just means moving the negative way. Values at the start of the clock get a subscript 0, as in s0s_0 and v0v_0.

Now send a cart from s=2 fts = 2\ \text{ft} out to s=12 fts = 12\ \text{ft}, then back to s=8 fts = 8\ \text{ft}. How far did it go? That question has two honest answers.

0 2 4 6 8 10 12 14 + s (ft) start end 10 ft out 4 ft back distance traveled = 14 ft displacement = +6 ft
One out-and-back trip, measured two ways

Displacement is the change in position, end minus start: 8−2=+6 ft8 - 2 = +6\ \text{ft}. It looks only at the two ends, and its sign says which way. Distance traveled is what an odometer on the cart would read: 10 ft out plus 4 ft back, or 14 ft. The two differ only when the body turns around. The Handbook prints neither definition, and it uses "displacement" loosely for ss itself. In exam questions, and in this Lesson, it means the change in ss.

Slopes walk down the chain

Velocity is how fast position changes. Acceleration is how fast velocity changes. A rate of change is a derivative, so the Handbook's Particle Rectilinear Motion block needs only two lines:

v=dsdta=dvdtv = \frac{ds}{dt} \qquad a = \frac{dv}{dt}

On a graph, a derivative is a slope. So the slope of the position graph is the velocity, and it takes one more step to reach acceleration, the slope of the velocity graph. Each differentiation walks one step down the chain. Here's one motion drawn all three ways, on the same clock.

0 2 4 6 8 s (ft) −4 0 4 8 v (ft/s) −12 −6 0 6 12 0 1 2 3 4 t (s) a (ft/s2) s = 6 s = 2 v = 0 v = 0 a = −6 a = +6 v is the slope of s a is the slope of v
One motion as position, velocity, and acceleration
Here s=t3−6t2+9t+2s = t^3 - 6t^2 + 9t + 2, with ss in feet and tt in seconds.

Run your finger along the top graph. Up to t=1 st = 1\ \text{s}, position climbs and velocity is positive. At t=1 st = 1\ \text{s} the curve goes flat for an instant, and velocity is zero. Then position falls until t=3 st = 3\ \text{s}, and velocity is negative: the body is going backward. The middle graph sets the acceleration below it the same way. Where it falls, aa is negative. At its bottom, t=2 st = 2\ \text{s}, a=0a = 0. Where it climbs, aa is positive.

The chain runs backward too. Velocity is the rate position changes, so the area under velocity adds up to the change in position, the way a flow rate adds up to the water in a tank. A steady 8 ft/s for 6 s moves the body 48 ft, the area of a rectangle. In the same way, the area under acceleration adds up to the change in velocity.

Reading a velocity-time graph

The exam's usual picture is a velocity-time graph made of straight segments, and straight segments need no calculus at all. Slopes are rise over run, and areas are triangles and rectangles. The Handbook prints nothing about these graphs, so the two rules travel with you:

  • The slope of a segment is the acceleration during it.
  • The signed area between the line and the time axis is the displacement. Area above the axis counts as positive, and area below as negative.
−4 0 4 8 0 2 4 6 8 10 12 14 16 18 t (s) v (ft/s) +16 ft +48 ft +16 ft −8 ft a = +2 ft/s2 a = 0 a = −2 ft/s2 a = +2 ft/s2
Slopes and signed areas on a velocity-time graph

The first segment climbs 8 ft/s in 4 s, so a=+2 ft/s2a = +2\ \text{ft/s}^2. The flat segment has a=0a = 0, which doesn't mean the cart has stopped: it's rolling steadily at 8 ft/s. The long falling segment keeps one slope straight through the moment it crosses zero.

For the areas, cut the graph into triangles and rectangles, including at each axis crossing. Above the axis the cart rolls forward. Below it, the cart backs up, so those slices subtract: 16+48+16−8=72 ft16 + 48 + 16 - 8 = 72\ \text{ft}. Counting the bottom triangle as positive gives 88 ft, which is the distance traveled, not the displacement.

Worked Example The railcar's chart
1 of 3

Here's the railcar's velocity chart, with forward as positive. Find its acceleration during the last 4 s and its displacement over the full 16 s.

−6 0 6 12 0 2 4 6 8 10 12 14 16 t (s) v (ft/s)
Velocity of the railcar

Judging a graph at a glance

Some questions hand you a graph and ask for a judgment, with no arithmetic. Two habits cover them.

Greatest acceleration means steepest. Slope is acceleration, so look for the steepest segment, whichever way it tilts. A downward slope is a negative acceleration, and its size still counts. The height of the line won't help, because height is velocity. A jet at cruise is fast with no acceleration, and a sprinter leaving the blocks is slow with plenty of it.

Reversing means crossing. Direction is the sign of vv, so the body turns around only where the line passes from one side of the time axis to the other. A peak isn't a reversal: it's only where the body stops gaining speed. Neither is a line that touches the axis and rises back up on the same side: the body pauses for an instant, then carries on the same way.

Checkpoint
1 of 2
−8 −4 0 4 8 0 2 4 6 8 10 12 14 t (s) v (ft/s) A B C D E
A velocity-time graph with five segments

In which segment is the size of the acceleration greatest?

A.
Segment A
B.
Segment B
C.
Segment C
D.
Segment D
E.
Segment E

Stopped, but still accelerating

Shove a cart up a long, smooth ramp. It slows, stops for an instant, and rolls back down. What's its acceleration at the instant it stops?

Instinct says zero, since the cart isn't moving. But acceleration doesn't ask how fast the cart is moving. It asks how fast its velocity is changing. With up the ramp as positive, say the cart starts at 8 ft/s and loses 4 ft/s every second. A tenth of a second before it stops, it's climbing at 0.4 ft/s. A tenth of a second after, it's rolling back at 0.4 ft/s. That's a change of 0.8 ft/s in 0.2 s, or 4 ft/s24\ \text{ft/s}^2, straight across the stop. The pull down the ramp never switches off, and velocity is just passing through zero on its way from up-the-ramp to down-the-ramp.

The graph shows it plainly. Velocity is one straight line, and it crosses zero at t=2 st = 2\ \text{s} with the same slope, −4 ft/s2-4\ \text{ft/s}^2, that it has everywhere else. Velocity is the line's height and acceleration is its slope, and a line can have no height and plenty of slope.

t = 0 a = −4 ft/s2 v = +8 ft/s t = 2 s a = −4 ft/s2 v = 0 t = 4 s a = −4 ft/s2 v = −8 ft/s + is up the ramp −8 −4 0 4 8 0 1 2 3 4 t (s) v (ft/s) v = 0, slope still −4 ft/s2
A cart on a ramp: velocity changes, acceleration doesn't

The same logic holds for anything that pauses to turn around. A velocity-time graph that is one straight line means constant acceleration, the subject of Constant-Acceleration Motion.

Checkpoint

A ball is thrown straight up. Ignoring air resistance, what are its velocity and acceleration at the very top of its path?

A.
v=0v = 0 and a=0a = 0
B.
v=0v = 0 and a=ga = g, downward
C.
v=0v = 0 and a=ga = g, upward
D.
v=0v = 0 and aa is less than gg, downward

Motion written as a polynomial

Sometimes the motion comes as an equation rather than a picture. The chain still runs both ways. Going down, differentiate. Take the motion from the three stacked graphs:

s=t3−6t2+9t+2v=dsdt=3t2−12t+9a=dvdt=6t−12\begin{aligned} s &= t^3 - 6t^2 + 9t + 2 \\ v &= \frac{ds}{dt} = 3t^2 - 12t + 9 \\ a &= \frac{dv}{dt} = 6t - 12 \end{aligned}

Put in a time to get the values then: at t=4 st = 4\ \text{s}, v=9 ft/sv = 9\ \text{ft/s} and a=12 ft/s2a = 12\ \text{ft/s}^2. To find when the body momentarily stops, set the velocity, not the position, to zero: 3(t−1)(t−3)=03(t - 1)(t - 3) = 0, so t=1 st = 1\ \text{s} and t=3 st = 3\ \text{s}, right where the position curve goes flat.

Going up, integrate, and here there's a catch. Differentiating threw information away: the 2 in ss vanished, and so did the 9 in vv. Given only a=6t−12a = 6t - 12, nothing can tell you what they were. They come back as constants of integration, and the initial conditions fix them:

v=3t2−12t+C,v=9 at t=0⇒C=9v = 3t^2 - 12t + C, \quad v = 9 \text{ at } t = 0 \quad\Rightarrow\quad C = 9

The Handbook's Non-constant Acceleration section prints the same thing with the constant built in: where you are now is where you began, plus everything added since. The τ\tau is only the integration variable, and vt0v_{t_0} and st0s_{t_0} are the values when the clock starts, usually v0v_0 and s0s_0.

v(t)=∫t0ta(τ) dτ+vt0s(t)=∫t0tv(τ) dτ+st0\begin{aligned} v(t) &= \int_{t_0}^{t} a(\tau)\,d\tau + v_{t_0} \\[4pt] s(t) &= \int_{t_0}^{t} v(\tau)\,d\tau + s_{t_0} \end{aligned}

If the known value is at a later time, put that time in and solve for CC. Leave the constant off, and you've quietly assumed the body started at rest at the origin. Displacement between two times needs no starting position, though: it's s(t2)−s(t1)s(t_2) - s(t_1), and the constant cancels.

The equations in the Handbook's Particle Rectilinear Motion column headed "Constant a=a0a = a_0," such as v=v0+a0tv = v_0 + a_0 t, don't apply when aa keeps changing.

Worked Example From acceleration up to position
1 of 4

A slider on a straight track has a=6ta = 6t in ft/s2\text{ft/s}^2, with tt in seconds. At t=0t = 0, it's at s0=4 fts_0 = 4\ \text{ft} and moving at v0=−12 ft/sv_0 = -12\ \text{ft/s}. When does it stop for an instant, and where is it then?

Total distance: split where it turns around

Now the odometer question. Run an integral of velocity straight across a whole trip, and the backward slices cancel some of the forward ones. That's right for displacement and wrong for distance, because an odometer never subtracts.

−16 −12 −8 −4 0 4 8 12 0 1 2 3 t (s) v (ft/s) +16 ft forward −7 ft back v = 0: it turns around
A trip with one turnaround, as areas under v = 12 − 3t²

So find where v=0v = 0 inside the interval, integrate each piece on its own, and add their sizes. A question asking for total distance, or how far a body travels, wants this. One asking for displacement, or how far it ends from its start, wants the net. If vv has no zero inside the interval, there's nothing to split, and the two answers have the same size. To check your work, run your calculator's numerical integration on ∣v∣|v| over the whole interval.

Worked Example Distance and displacement for one turnaround
1 of 3

A cart's velocity is v=12−3t2v = 12 - 3t^2, with vv in ft/s and tt in seconds. Find the total distance it travels from t=0t = 0 to t=3 st = 3\ \text{s}, and its displacement.

Recap

  • Choose one axis and a positive direction, and signs carry direction. Displacement is the change in ss, distance traveled is the odometer reading, and they differ only when the body turns around.
  • Since v=ds/dtv = ds/dt and a=dv/dta = dv/dt, differentiating walks down the chain and integrating walks back up, with v0v_0 and s0s_0 fixing the constants.
  • On a velocity-time graph, slope is acceleration and signed area is displacement. The steepest segment has the greatest acceleration, and the body reverses only where the line crosses zero.
  • Zero velocity doesn't mean zero acceleration: a ball at the top of its path has v=0v = 0 and a=ga = g downward.
  • For total distance, split where v=0v = 0, integrate each piece, and add the sizes.