Back

Dynamics

  • Topic 5
  • 8 Lessons

Overview

Every dynamics question does one of two jobs: it describes motion, or it explains it. Describing is kinematics: how far, how fast, how quickly the speed is changing. Explaining is kinetics: what force made that happen. The explaining has two main routes, and one question picks between them: is time given, or distance?

Forces with time lead to F=maF = ma. Speeds with distances lead to work-energy, which never needs the acceleration. So before you write any equation, list what's given and what's asked, then ask the question. You'll use that habit all through this topic.

List what's given and what's asked Describing the motion, or explaining it with forces? describing Kinematics no forces needed explaining Is time given, or distance? time, or a single instant F = ma impulse-momentum is its time-based form distance Work-energy never needs the acceleration
The habit: two questions before any equation

Describing, then explaining

Picture a hockey puck leaving your stick at 30 ft/s and coasting to a stop across the ice, 10 s and 150 ft later. A stopwatch and a tape measure tell you all of that, and nobody has said a word about why it stopped. That's kinematics, the business of Position, Velocity, and Acceleration and Constant-Acceleration Motion.

Kinetics asks why. The ice dragged on the puck, and that force, acting on the puck's mass, set the acceleration. The acceleration is where the two halves meet: kinetics finds it from the forces, and kinematics turns it into speeds and distances.

The test isn't what the question asks for, since a speed can be the answer either way. If the motion numbers alone get you there, you're describing. If a force has to enter, even one nobody mentions, like gravity on a slope or a spring's push, you're explaining.

Is time given, or distance?

Now ask how hard the ice dragged. If the problem hands you the 10 s, you have a force acting for a time, and F=maF = ma is the route: the speed lost in that time gives the acceleration, and the acceleration gives the force. That's Newton's Second Law. Impulse and Momentum is the same law written for a force acting over a time, so it rides along on this route.

If the problem hands you the 150 ft instead, you have a force acting through a distance, and work-energy goes straight from the speed to the force, with no time and no acceleration anywhere in it. That's Work and Energy, and Power and Efficiency then asks how fast that work gets done.

A force at one instant, like the pull in a tow rope the moment a sled starts moving, goes with F=maF = ma too, since nothing has traveled any distance yet. When both routes could work, they reach the same force, so the question is only finding you the shorter path. The Handbook's Dynamics section prints these equations without saying which one to reach for, so that choice is yours.

Rotation mirrors translation

Shove a playground merry-go-round, and the same story plays out with new letters. Angular position θ\theta replaces ss, angular velocity ω\omega replaces vv, and angular acceleration α\alpha replaces aa. The moment you apply, or torque, does the job of the force. The mass moment of inertia II does the job of the mass: it's how hard the body resists spinning up. So M=IαM = I\alpha reads just like F=maF = ma. Rotation and Circular Motion and Mass Moment of Inertia fill in the details.

Translation m F a F = ma Rotation I M α M = Iα position s angular position θ velocity v angular velocity ω acceleration a angular acceleration α mass m mass moment of inertia I force F moment M
Translation and rotation, pair by pair

Units decide many answers

Plenty of wrong answers in dynamics are good physics with bad units. Three conversions do most of the damage:

  • Weight to mass. A weight in pounds is a force, and the mm in F=maF = ma isn't one. Mass is W/gW/g, which comes out in slugs.
  • mph to ft/s. A speed in mph has to become ft/s before it meets an acceleration in ft/s².
  • rpm to rad/s. Rotation's equations work in radians, so a speed in rpm has to become rad/s first.

Naming the idea

Now try the habit. None of these needs a calculation: read each situation, and name what it calls for.

Checkpoint
1 of 4

A 3,000 lb car brakes from 60 mph to a stop. Here are three versions of the problem:

  1. The stop takes 4 s. Find the braking force.
  2. The stop takes 176 ft. Find the braking force.
  3. The stop takes 176 ft. Find the deceleration.

Which approach is the most direct for each?

A.
1: work-energy. 2: F=maF = ma. 3: kinematics.
B.
1: F=maF = ma. 2: kinematics. 3: work-energy.
C.
1: F=maF = ma. 2: work-energy. 3: kinematics.
D.
1: kinematics. 2: work-energy. 3: F=maF = ma.