USCS Classification

Two sieves and two water contents put a two-letter name on any soil.

Before this Lesson

A boring log doesn't say "brownish, kind of sticky." It says CH, or SP-SM. Read CH and you already suspect a soil that swells when it wets and gives up its water slowly. Read GW and you picture a tight, free-draining gravel. You haven't touched either one. Those names come out of a short chain of questions, always asked in the same order, and you already know how to get every number they need.

A name in two letters

The first letter says what the soil mostly is: G for gravel, S for sand, C for clay, and M for silt. S was taken, so silt borrowed its letter from mo, a Swedish word for fine soil. O for organic soil and PT for peat are rarer, and naming them is as far as this Lesson goes.

The second letter adds the one detail that matters most for that kind of soil. A gravel or sand gets W or P for how well it's graded, or M or C for how its fines behave. A silt or clay gets L or H for low or high plasticity.

Gravels and sands
Second letterG: gravelS: sand
W: well gradedGW, well-graded gravelSW, well-graded sand
P: poorly gradedGP, poorly graded gravelSP, poorly graded sand
M: silty finesGM, silty gravelSM, silty sand
C: clayey finesGC, clayey gravelSC, clayey sand

Adapted from the FE Reference Handbook, ASTM D2487-11 Unified Soil Classification System table

Silts and clays
Second letterM: siltC: clay
L: low plasticityML, siltCL, lean clay
H: high plasticityMH, elastic siltCH, fat clay

Adapted from the FE Reference Handbook, ASTM D2487-11 Unified Soil Classification System table

Fat and lean are old field words: a fat clay feels greasy between your fingers, and a lean one less so. All of these, and the thresholds that follow, come from one Handbook table, headed ASTM D2487-11, with Unified Soil Classification System in parentheses. That's the USCS of this Lesson's title. Search the Handbook for the full phrase and not for USCS, which there means U.S. Customary System.

Two questions, in order

Classification asks two questions, in order. Is the soil coarse or fine? The answer picks the second question. In a coarse soil, grains rest on grains, so grain size and gradation set the name. In a fine soil, water takes over, as you saw in Grain Size and Plasticity, so plasticity sets the name.

The No. 200 sieve answers the first question. If more than 50% of the soil is retained on it, the soil is coarse-grained. Otherwise it's fine-grained. Mind the wording: the rule says retained, and questions usually give percent passing. A soil with 38% passing has 62% retained, so it's coarse-grained, even with more than a third of it fines.

Percent retained on the No. 200 sieve more than 50% 50% or less Coarse-grained Share of the coarse fraction on the No. 4 sieve more than half G half or less S Percent fines (passing the No. 200) under 5% W or P, from CU and CC GW, GP, SW, SP 5 to 12% Dual symbol: gradation, then fines such as SP-SM, SW-SC over 12% M or C, from where the fines plot GM, GC, SM, SC Fine-grained Liquid limit, LL below 50 L 50 or more H PI against the A-line on or above C, a clay CL, CH below M, a silt ML, MH
The whole USCS decision sequence

The rest of this Lesson walks through that chart. After coarse or fine, in words:

  • Gravel or sand: the No. 4 sieve splits them. If more than half of the coarse fraction, the part retained on the No. 200, stays on it, the soil is gravel, and otherwise it's sand.
  • Fines in a coarse soil: under 5% takes W or P from the gradation, over 12% takes M or C from the fines, and 5 to 12% takes a dual symbol with both.
  • Fine soil: LLLL below 50 is L and 50 or more is H, and a line on a chart decides C or M.
Checkpoint
1 of 4

A sieve analysis reports that 43% of a soil passes the No. 200 sieve. What does the USCS call it, and why?

A.
Fine-grained, because less than 50% of it passes
B.
Coarse-grained, because more than 50% of it is retained
C.
Fine-grained, because its fines are over 12%
D.
No call is possible without the liquid and plastic limits

Fine soils and the A-line

Take the fine branch first, because the coarse branch borrows its main tool.

Two soils can share a liquid limit and still behave very differently. Both turn to soup at the same water content. But dry them down from there and one stays moldable over a wide range, while the other soon starts to crumble. The first is acting like clay, whose thin plates grip water and each other. The second is acting like silt, finely ground rock that can hold plenty of water in its pores without getting any stickier.

So plot each soil by both numbers, with LLLL across and PI=LL−PLPI = LL - PL up. Clays land high and silts land low. Arthur Casagrande, who built this system for wartime airfields, plotted a great many soils this way and drew a boundary between them, the A-line. The Handbook prints its equation in a note on the chart just below the classification table:

PIA=0.73(LL−20)PI_A = 0.73(LL - 20)

The Handbook writes the left side as plain PIPI. The subscript is ours, to keep the line's height apart from the soil's own PIPI. There's no law behind the 0.73. It's a boundary drawn from experience.

0 10 16 20 30 40 50 60 70 80 90 100 110 0 4 7 10 20 30 40 50 60 Liquid limit, LL Plasticity index, PI PI = 0.73(LL - 20) "A" line PI = 0.9(LL - 8) "U" line CL or OL CH or OH ML or OL MH or OH CL-ML
The plasticity chart

Adapted from the FE Reference Handbook, chart below the ASTM D2487-11 Unified Soil Classification System table

Two lines do nearly all the work. The vertical at LL=50LL = 50 sets the second letter: below 50 is L, and 50 or more is H. The A-line sets the first letter: on or above it is C, and below it is M. So compute PIPI, compute PIAPI_A from LLLL, and compare them. The rest of the chart needs only a line each:

  • At the far left, the A-line runs flat at PI=4PI = 4 out to LL=25.5LL = 25.5. The hatched band above it, up to PI=7PI = 7, is CL-ML, a silty clay. Those soils are too close to call, so they get both names.
  • The dashed U-line, PI=0.9(LL−8)PI = 0.9(LL - 8), is a rough ceiling on real soils, and a point above it usually means a bad lab number. The Handbook prints it without comment.
  • The solid diagonal from the origin is PI=LLPI = LL, where the plastic limit would be zero.
  • Each zone also names an organic soil, as in "CL or OL", because organic soils plot in the same places. A separate oven-drying test sorts those out, and we're setting them aside.
Worked Example A fine soil from its limits
1 of 3

A soil has 72% passing the No. 200 sieve, LL=62LL = 62, and PL=28PL = 28. Classify it.

Reading a point off the chart

A question may skip the arithmetic and hand you a description or a marked point. Then all that matters is which side of each line it's on. Height alone doesn't settle it, because the A-line climbs as you move right. A PIPI of 30 sits above the line at LL=48LL = 48 but below it at LL=80LL = 80.

Checkpoint
1 of 3

Where on the plasticity chart does a lean clay plot?

A.
Below the A-line, left of LL = 50
B.
Below the A-line, right of LL = 50
C.
Above the A-line, left of LL = 50
D.
Above the A-line, right of LL = 50

The plastic limit that lands on the line

You can run the A-line backward. Pin a soil's liquid limit at 60. The line's height there is fixed: PIA=0.73(60−20)=29.2PI_A = 0.73(60 - 20) = 29.2. The soil's own PIPI is 60−PL60 - PL, so now the plastic limit alone decides which side of the line it lands on. It lands right on the line when 60−PL=29.260 - PL = 29.2, a plastic limit of 30.8. In general:

PLA=LL−0.73(LL−20)PL_A = LL - 0.73(LL - 20)

Now the part that feels backward: a higher plastic limit means a less plastic soil. The plastic limit is where the soil stops crumbling as water goes in, and the liquid limit is where it starts to flow. With LLLL pinned, raising PLPL squeezes the range between them, PIPI falls, and the point drops below the A-line. So a measured plastic limit above PLAPL_A means a silt, and one below it means a clay.

0 10 20 30 40 50 60 70 Water content, % LL = 60 PLA = 30.8 PL = 24, PI = 36 above the A-line: CH PL = 30.8, PI = 29.2 on the A-line PL = 38, PI = 22 below the A-line: MH
Three soils with the same liquid limit and different plastic limits
Checkpoint
1 of 2

A fine-grained soil has LL=44LL = 44. At what plastic limit would it sit exactly on the A-line?

Coarse soils: gravel or sand

On to the coarse branch. The first letter comes from the No. 4 sieve, and here's the catch: the test isn't about the whole sample. It's about the coarse fraction, the part that stayed on the No. 200. Fines are out of this contest, since they're neither gravel nor sand. If more than half of the coarse fraction stays on the No. 4, the soil is gravel. Otherwise it's sand.

Take a soil with 60% passing the No. 4 and 35% passing the No. 200. Only 40% of the sample stayed on the No. 4, so it's tempting to call it a sand. But the coarse fraction is only 65% of the sample, and 40 of that 65 is gravel.

Gravel 40% Sand 25% Fines 35% No. 4 sieve No. 200 sieve Coarse fraction: 65% Gravel is 40 of 65, or 62% of the coarse fraction
A sample with 60% passing the No. 4 and 35% passing the No. 200

With P4P_4 and P200P_{200} as the percent passing each sieve:

share of coarse fraction on the No. 4=100−P4100−P200\text{share of coarse fraction on the No. 4} = \frac{100 - P_4}{100 - P_{200}}

Here that's 40/65=62%40 / 65 = 62\%, so the soil is a gravel. The share tops one half exactly when there's more gravel than sand, which makes a quick check: 40% gravel beats 25% sand.

Clean soils and dual symbols

Next, count the fines. They decide whether the gradation still matters. Under 5% fines the soil is clean. There's too little fine material to change how it behaves, so the gradation alone gives the second letter, W or P. Earning the W takes passing both coefficient tests.

From 5 to 12% fines, the gradation still counts, but now the fines count too, so the soil takes a dual symbol with both. The first half comes from the gradation. The second comes from plotting the fines' LLLL and PLPL on the same plasticity chart: below the A-line is M, and on or above it is C. A poorly graded sand whose fines plot below the line is SP-SM, which the Handbook names poorly graded sand with silt.

The dual symbols get no rows in the Handbook's table. They're in its footnotes C and H, so they're easy to miss. Most other footnotes add phrases such as "with sand", and those change the name, not the symbol.

Worked Example A sand with 8% fines
1 of 3

A soil has 96% passing the No. 4 sieve and 8% passing the No. 200, with D60=0.72D_{60} = 0.72 mm, D30=0.16D_{30} = 0.16 mm, and D10=0.09D_{10} = 0.09 mm. Its fines have LL=38LL = 38 and PL=28PL = 28. Classify it.

More than 12% fines

Past 12%, the fines fill the gaps between the grains and start to run the show, so the gradation of the coarse part stops being the useful question. Skip CUC_U and CCC_C. The second letter comes only from where the fines plot: below the A-line is M, and on or above it is C. The LL=50LL = 50 line plays no part here, since a coarse soil has no L or H to give out. If the fines land in the hatched band, the Handbook's footnote F makes the symbol dual, GC-GM or SC-SM.

Worked Example A gravel that doesn't look like one
1 of 3

A soil has 55% passing the No. 4 sieve and 30% passing the No. 200. Its fines have LL=42LL = 42 and PL=18PL = 18. Classify it.

Recap

  • Coarse or fine comes first: more than 50% retained on the No. 200 is coarse-grained, and questions usually give percent passing. Size and gradation name a coarse soil, and plasticity names a fine one.
  • Gravel or sand comes from the share of the coarse fraction on the No. 4, (100−P4)/(100−P200)(100 - P_4) / (100 - P_{200}), not the share of the whole sample. Above one half is gravel.
  • Under 5% fines takes W or P, which needs both CUC_U and CCC_C. Over 12% takes M or C from where the fines plot. From 5 to 12% takes a dual symbol: gradation first, then fines.
  • For a fine soil, LLLL below 50 is L and 50 or more is H. A PIPI on or above 0.73(LL−20)0.73(LL - 20) is C, and below it is M.
  • A soil sits on the A-line when PL=LL−0.73(LL−20)PL = LL - 0.73(LL - 20). A measured plastic limit above that means a smaller PIPI, so a silt.