Back

Geotechnical Engineering

  • Topic 12
  • 18 Lessons

Overview

Soil is grains with water and air in the gaps between them, and the water decides almost everything. How much water fills the gaps sets how much the soil weighs. How hard that water pushes decides how hard the grains press on each other, which sets how strong the soil is and how much it squeezes under a load. And how fast the water can escape sets how fast a clay settles.

So the topic runs on one habit: fill in the phase diagram, build the effective-stress profile, and only then reach for a design equation. Strength, settlement, earth pressure on walls, and bearing capacity under footings all run on the effective stress σ′\sigma'. Find σ′\sigma' first, and most of the topic becomes substitution.

1 Phase diagram Air Water Solids γ, γsat, γ′ 2 Effective stress σ′ = σ − u find σ′ first 3 Strength friction between grains Earth pressure Slope stability Bearing capacity 4 Consolidation clay squeezes as water escapes How much: Δσ′ How fast: drainage
The habit behind every geotechnical problem
The phase diagram supplies the unit weights, the unit weights build the effective-stress profile, and everything below it runs on σ′\sigma'. The numbers match the four ideas below.

1. Soil has three phases, and its properties are ratios among them. Imagine sorting a clod of soil into three layers: the solids at the bottom, the water above them, the air on top. That's the phase diagram, and water content, void ratio, porosity, degree of saturation, and unit weight are each a ratio of two of its parts. The solids are the yardstick, because they're the one part that doesn't change. A compactor drives out air, and soil hauled from a borrow pit arrives at the fill with exactly the same weight of grains it left with. Even the Atterberg limits that help name a clay are water contents.

2. Effective stress controls strength, compression, and earth pressure. The weight of everything above a point, per unit area, is the total stress σ\sigma. Below the water table, the water in the pores is under a pressure uu that pushes the grains apart and holds up part of that weight. The grains press on each other with only what's left, which the Handbook writes as σ′=σ−u\sigma' = \sigma - u. Grains are what grip, squeeze together, and push on walls, so it's σ′\sigma', not σ\sigma, that runs all three. Here's the strange part: let a lake rise 10 ft over a saturated site, and σ\sigma and uu at every depth go up by exactly the same amount. σ′\sigma' doesn't change, and the soil can't tell the lake is there.

3. Soil strength is friction between grains. Soil has little glue. It resists sliding the way a book resists being pushed across a table: the harder it's pressed down, the harder it grips. The Handbook's shear stress at failure, τF=c+σNtan⁡ϕ\tau_F = c + \sigma_N\tan\phi, is that friction law, with tan⁡ϕ\tan\phi as the friction coefficient, cc as whatever cohesion the soil has, and the normal stress σN\sigma_N as the press. Only the grains feel that press, so it's their share, σ′\sigma', that counts. Push water up through a sand hard enough to bring σ′\sigma' to zero, and the sand holds nothing, whatever its friction angle. That's quicksand, a condition rather than a kind of sand. Earth pressure on walls, slope stability, and bearing capacity are this same friction, worked out for different shapes of soil trying to slide.

4. Clay settles slowly because the water has to squeeze out. Put a new load on saturated clay, and at first the grains don't feel it. The water can't get out of the way, so it takes the whole load as extra pore pressure. The clay compresses only as that water seeps out to a sand layer or the surface, and the grains take over the load bit by bit as it goes. In sand, the water is gone about as fast as the load goes on. In clay, the pores are so fine that the trip is slow, and its length matters most: the time grows with the square of the distance the water has to travel, so halving that distance cuts the time to a quarter. How much the clay settles in the end depends on how far σ′\sigma' climbs, and on whether the clay has carried that much before.

Most questions in this topic lean on one of these ideas more than the others, and spotting which one is the first step. Try it on four situations.

Checkpoint
1 of 4

A city pumps groundwater from deep wells for decades, and the water table drops 50 ft. Over the same years, the ground surface sinks several feet, though nothing new was built on it. Which idea explains why the ground sinks at all?

A.
Soil has three phases, and its properties are ratios among them
B.
Effective stress controls strength, compression, and earth pressure
C.
Soil strength is friction between grains
D.
Clay settles slowly because the water has to squeeze out

The Lessons below follow the habit in order: the phase diagram, unit weights, classification, and compaction first; then effective stress and the ways it changes; then consolidation and strength; and finally the walls, slopes, and footings that put them all to work.

Lessons

  1. 1Soil as Three PhasesDraw the box of solids, water, and air, and every soil property is a ratio of its parts.
  2. 2Unit Weights of SoilThe same soil weighs more or less depending on how much water fills its voids.
  3. 3Grain Size and PlasticityCoarse soils are sorted by grain size, fine soils by how they behave with water.
  4. 4USCS ClassificationTwo sieves and two water contents put a two-letter name on any soil.
  5. 5The Proctor TestA little water helps soil pack tighter; too much pushes the grains apart.
  6. 6Field Compaction ControlThe specification names a dry unit weight, and the field test proves you hit it.
  7. 7Effective StressWater pressure pushes the grains apart, so only part of the soil's weight presses them together.
  8. 8Changing Effective StressLower the water table, and the ground presses down harder without adding any soil.
  9. 9Compressibility and PreconsolidationClay remembers the heaviest load it has ever carried.
  10. 10Consolidation SettlementSettlement is the clay's voids shrinking under a new effective stress.
  11. 11Time Rate of ConsolidationClay settles as fast as water can escape it, and halving the drainage path makes it four times faster.
  12. 12Shear StrengthSoil strength is friction between grains, and friction needs the grains pressed together.
  13. 13Triaxial Tests and Failure PlanesAt failure, Mohr's circle just touches the strength envelope, and that one point fixes everything else.
  14. 14Lateral Earth PressureHow hard soil pushes on a wall depends on whether the wall moves away, stays put, or pushes back.
  15. 15Earth Pressure with Water and SurchargeWater behind a wall pushes at full strength in every direction, which soil never does.
  16. 16Slope StabilityA slope stands as long as the soil's strength outruns gravity's pull along the slip surface.
  17. 17Bearing CapacityA footing fails when it shoves a wedge of soil out from under itself.
  18. 18Footing Size and the Water TableWet soil carries less, so the footing has to grow to make up for it.