Traffic Flow Fundamentals

A highway lane is a conveyor belt of cars, and q=kvq = kv is its speedometer.

At 3 a.m., a freeway lane is wide open. The few cars on it do 70 mph, and you could watch from an overpass for a full minute before one goes by. At 5:30 p.m., the same lane is packed bumper to bumper and nobody is moving. One lane has the speed, the other has the cars, and neither gets much traffic anywhere. So a lane must carry the most at some state in between, and by the end of this Lesson you'll be able to say exactly where.

A lane is a moving line of cars

To say how much a lane carries, you need three numbers, and each comes from a different way of looking at the road.

  • Flow is a count at a place. Stand at one point and count the vehicles going by, per hour (veh/h).
  • Density is a count at a moment. Freeze the clock and count the vehicles on a stretch of road, per mile (veh/mi).
  • Space-mean speed is how fast the line of cars moves as a whole, in mph. "Space-mean" names a particular way of averaging, and we'll come back to it.

Now picture the lane as one long line of cars sliding past you. Say every mile of the line holds 30 cars, and the line moves at 60 mph. In one hour, 60 miles of it go by, each mile bringing its 30 cars, so 1,800 cars pass you. Flow is density times speed:

q=kvq = kv
v = 60 mph 1 mile holds k = 30 cars 60 miles of the line pass in 1 hour Counting point q = (30)(60) = 1,800 cars per hour
In one hour, 60 miles of the line pass the counting point
Not to scale: the line continues past the break, and each mile holds 30 cars, not the five drawn.

The Handbook doesn't print q=kvq = kv. In its Transportation section, flow is VV, density is DD, and speed is SS, so from here on the same relation reads V=DSV = DS. It prints that relation on its own only once, rearranged, under Basic Freeway Segment Highway Capacity: D=vp/SD = v_p/S. There, vpv_p is a per-lane flow adjusted for peaks and trucks, which a later Lesson, Peak Hour Factor and Demand Flow Rate, builds. The Handbook reuses those letters: in its sight distance equations, VV is a speed and SS is a distance, so read the definitions under each equation.

V=DSV = DS works for one lane or for a whole direction, as long as flow and density are on the same basis. Three lanes at 1,800 veh/h/ln carry 5,400 veh/h and hold 90 veh/mi, or 30 veh/mi/ln. Speed doesn't add up across lanes: it's 60 mph either way.

Worked Example Density per lane from a whole direction's flow
1 of 3

A three-lane freeway direction carries 4,500 veh/h in total at a space-mean speed of 50 mph. Find the density per lane.

Turning field counts into flow

Field data rarely arrives in those units, and two conversions come up again and again.

A flow is an hourly rate, even when nobody counted for an hour. A count of 150 vehicles in 5 minutes is a rate of 150 × 12 = 1,800 veh/h, because twelve 5-minute periods fit in an hour.

A speed in ft/s has to become mph, because density is per mile and flow is per hour. One mph is 5,280 ft in 3,600 s, or about 1.47 ft/s, so divide by 1.47: 88 ft/s is 60 mph. The Handbook's Units and Conversion Factors table gives the 5,280, and 1.47 appears as a bare coefficient in its stopping sight distance equation.

Checkpoint

During a 5-minute count, 130 vehicles pass a point in one lane. Their space-mean speed is 66 ft/s. What is the density?

A.
34.7 veh/mi/ln
B.
23.6 veh/mi/ln
C.
16.1 veh/mi/ln
D.
2.9 veh/mi/ln

One car at a time

Those lane-wide numbers have a car-sized version. If 1,800 vehicles pass in an hour, and an hour has 3,600 seconds, one passes every 2 seconds on average. That's the time headway: the time between one front bumper crossing a point and the next front bumper crossing it. If 30 vehicles share a mile, each gets 5,280/30 = 176 ft. That's the spacing: front bumper to front bumper, at one instant.

headway (s)=3,600Vspacing (ft)=5,280D\text{headway (s)} = \frac{3{,}600}{V} \qquad \text{spacing (ft)} = \frac{5{,}280}{D}

The Handbook prints neither, so you build them from the seconds in an hour and the feet in a mile. Each is the reciprocal of its partner, flow with headway and density with spacing, and the pairs don't cross. Headway belongs to flow alone: cars crossing a line every 2 seconds could be doing 20 mph or 70.

A photo gets you to spacing from a raw count. With 24 cars on a half mile of one lane, the density is 24/0.5 = 48 veh/mi, and the spacing is 5,280/48 = 110 ft. Running that backward, a 110-ft spacing is a density of 48 veh/mi.

The two pairs link through speed. The car behind reaches the spot where the car ahead was in exactly one headway, so it covers one spacing in one headway:

S=spacingheadway=176 ft2 s=88 ft/s=60 mphS = \frac{\text{spacing}}{\text{headway}} = \frac{176\ \text{ft}}{2\ \text{s}} = 88\ \text{ft/s} = 60\ \text{mph}

That's V=DSV = DS again, one car at a time, and it comes out in ft/s.

Checkpoint
1 of 3

A lane carries 1,500 veh/h at a space-mean speed of 55 mph. What is the average time headway?

s

Headway is not a gap

Headway and spacing both run front bumper to front bumper, so they include the car itself. The gap is only the empty part: the time from one car's rear bumper clearing a point to the next car's front bumper reaching it. Take the headway and subtract the time one vehicle length LL takes to pass:

gap=headway−LS\text{gap} = \text{headway} - \frac{L}{S}

Here LL is in feet and SS is in ft/s. At 88 ft/s, a 20-ft car takes 0.23 s to pass, so a 2.00-s headway leaves a 1.77-s gap. The Handbook doesn't define a gap in a traffic stream, so a question that uses one will say what it means.

t = 0 s A B t = 0.23 s A B t = 2.00 s A B spacing = 176 ft L = 20 ft S = 88 ft/s (60 mph) Counting point L/S = 0.23 s headway = 2.00 s gap = 1.77 s
Headway and gap at a fixed point, for cars 176 ft apart
Both cars move at 88 ft/s (60 mph), and each is 20 ft long. The same counting point runs through all three moments.
Checkpoint

A lane carries 1,200 veh/h at a space-mean speed of 45 mph, and vehicles average 22 ft long. What is the average gap, taken as the headway less the time one vehicle length takes to pass?

A.
3.00 s
B.
2.67 s
C.
2.51 s
D.
0.33 s

Which speed, and how full a lane gets

Back to that word "space-mean." There are two ways to average the speeds in a stream. Stand at one point with a radar gun and average what you clock: that's the time-mean speed. Freeze a stretch of road and average the speeds of the cars on it: that's the space-mean speed. They differ because fast cars pass you more often than slow ones, so the radar gun oversamples them, and the time-mean speed comes out equal or higher. Density is a freeze frame, so the speed that belongs with it in V=DSV = DS is the average over that same frame. The Handbook just says "mean speed" and doesn't draw the distinction.

Now keep adding cars to a lane. The spacing shrinks and drivers slow, until cars sit nearly bumper to bumper and traffic stops. That's the jam density, DjD_j in the Handbook. A spacing of about 26 ft, one car and a few feet of air, works out to about 200 veh/mi/ln.

Checkpoint

Which of these statements are true?

A.
A lane whose flow doubles has half the average headway.
B.
The speed in V=DSV = DS is the time-mean speed, the average of speeds clocked at one point.
C.
A lane whose density doubles has half the average spacing.
D.
At jam density the flow is at its maximum, because the lane holds the most vehicles.
E.
At jam density the speed and the flow are both zero.

Why flow has a peak

Now the opening question. V=DSV = DS says flow needs both cars and speed, and real traffic trades one for the other. The Greenshields model makes the simplest guess about that trade: speed falls in a straight line with density, from a free-flow speed SfS_f on an empty road to zero at jam density. The Handbook's Traffic Flow Relationships section prints it this way, describing SfS_f as the speed the first driver entering the facility would select:

S=Sf−SfDjDS = S_f - \frac{S_f}{D_j}D

Multiply through by DD to get flow, and the straight line becomes a parabola, also as the Handbook prints it:

V=SfD−SfDjD2V = S_f D - \frac{S_f}{D_j}D^2

This curve is zero at D=0D = 0, where there are no cars, and zero at D=DjD = D_j, where they don't move. A parabola peaks halfway between its zeros, so maximum flow comes at half the jam density. The straight line then says the speed there is half the free-flow speed. Multiply the two halves together for the maximum flow:

Do=Dj2So=Sf2Vm=DoSo=DjSf4D_o = \frac{D_j}{2} \qquad S_o = \frac{S_f}{2} \qquad V_m = D_oS_o = \frac{D_jS_f}{4}

So a lane carries the most when it's half full and moving at half speed. The Handbook prints the equations for DoD_o and VmV_m, calling DoD_o the optimum (or critical) density and SoS_o the optimum (or critical) speed. It leaves So=Sf/2S_o = S_f/2 for you to read off the line.

0 Do Dj 0 Do Dj Sf So Vm Speed, S (mph) Flow, V (veh/h/ln) Density, D (veh/mi/ln) Uncongested Congested
Speed falls in a straight line, so flow traces a parabola

Adapted from the FE Reference Handbook, Traffic Flow Relationships (Greenshields Model)

Checkpoint

A lane follows the Greenshields model with a free-flow speed of 70 mph and a jam density of 180 veh/mi/ln. What is its maximum flow, and at what density and speed does it occur?

A.
6,300 veh/h/ln at 90 veh/mi/ln and 70 mph
B.
12,600 veh/h/ln at 180 veh/mi/ln and 70 mph
C.
3,150 veh/h/ln at 90 veh/mi/ln and 35 mph
D.
6,300 veh/h/ln at 180 veh/mi/ln and 35 mph

Every flow below VmV_m shows up twice on the parabola. On the left branch the road is uncongested, and adding cars raises the flow. On the right branch it's congested, and adding cars lowers the flow, because each added car now cuts the speed by a bigger percentage than it raises the density. The same flow can be a few fast cars or many slow ones. The Handbook's figure draws that right branch dash-dot and labels it "Oversaturated flow." It also adds a third panel of speed against flow, which is the same model on different axes.

Worked Example A stated density, and a stated flow
1 of 3

A lane follows the Greenshields model with Sf=60 mphS_f = 60\ \text{mph} and Dj=200 veh/mi/lnD_j = 200\ \text{veh/mi/ln}. Find the speed and flow at a density of 50 veh/mi/ln. Then find the two densities that carry 1,920 veh/h/ln.

When a question only asks you to recognize the model, the shape and the two halves are all you need.

Checkpoint
1 of 2

Which plot shows the flow-density curve of the Greenshields model?

A.
0 Dj Density Flow
B.
0 Dj Density Flow
C.
0 Dj Density Flow
D.
0 Dj Density Flow

Recap

  • A lane is a moving line of cars, so q=kvq = kv, or V=DSV = DS in the Handbook's letters, with flow and density on the same basis and the speed a space-mean speed.
  • Convert field data first: a short count to an hourly rate, and ft/s to mph by dividing by 1.47.
  • Headway 3,600/V3{,}600/V and spacing 5,280/D5{,}280/D are flow and density one car at a time. Spacing over headway is the speed in ft/s, and a gap is the headway less the passing time L/SL/S.
  • In the Greenshields model, speed falls linearly from SfS_f to zero at DjD_j, and flow is a parabola that peaks at Vm=DjSf/4V_m = D_jS_f/4, at half the jam density and half the free-flow speed.
  • Every flow below the maximum happens at two densities, and the higher one is the congested one.