Forces on Pipe Bends and Nozzles

A pipe bend must be held in place against the water it turns.

Dig up a buried water main where it turns a corner, and you'll usually find a mass of concrete poured between the outside of the bend and undisturbed soil. It's called a thrust block. Leave it out, and the bend can shove its way through the soil until a joint pulls apart.

How hard does the bend shove? A 12 in. main at 100 psi, turning 90° while it carries 3 ft³/s, pushes on its bend with about 16,000 lb. Yet the water inside creeps along at 3.8 ft/s, slower than you walk. A jet that slow, carrying the same flow square onto a wall, would push it with about 22 lb. Where does the rest come from?

Two pushes on the water

Treat the bend the way Forces from Jets on Plates and Vanes treated a vane. Draw a control volume around the water inside it, cutting square across the pipe at section 1, where the water enters, and at section 2, where it leaves, and list every outside force on that water.

For a free jet, the list held only the vane, since open air at zero gauge pressure surrounds the jet. Inside a full pipe, each cut has more water pressing on the other side, with a force equal to its pressure times the pipe's area. Pressure only pushes, never pulls, so both forces point into the control volume: P1A1P_1A_1 downstream at the inlet, and P2A2P_2A_2 back against the outgoing flow at the outlet. Add the bend's own push on the water, FF. The water's weight acts straight down, square to a horizontal bend, so it drops out.

1 2 v1 v2 P1A1 P2A2 P1A1 + ρQv1 P2A2 + ρQv2 bend's push on the water x y
The forces on the water in a 90° bend

Write ΣF=ρQ(v2−v1)\Sigma F = \rho Q(v_2 - v_1) once per direction, with x along the incoming flow and y along the outgoing flow. Along x, P1A1P_1A_1 shoves the water forward, yet its x-momentum drops to zero, so the bend has to cancel the shove and stop the water too. Along y, P2A2P_2A_2 shoves the water back, yet it gains y-momentum, so the bend has to beat the shove and speed the water into the turn:

P1A1+Fx=ρQ(0−v1)⇒Fx=−(P1A1+ρQv1)−P2A2+Fy=ρQ(v2−0)⇒Fy=P2A2+ρQv2\begin{aligned} P_1A_1 + F_x &= \rho Q(0 - v_1) &\quad\Rightarrow\quad F_x &= -(P_1A_1 + \rho Qv_1) \\[4pt] -P_2A_2 + F_y &= \rho Q(v_2 - 0) &\quad\Rightarrow\quad F_y &= P_2A_2 + \rho Qv_2 \end{aligned}

So the water pushes on a bend in two ways, by its pressure and by having its momentum changed, and here the two add in each direction. The bend has to answer both, and the anchor holds the bend while it does.

In the Hook's main, each pressure force is 100 psi×113.1 in2=11,310100\ \text{psi} \times 113.1\ \text{in}^2 = 11{,}310 lb, while ρQv=1.94(3)(3.82)=22\rho Qv = 1.94(3)(3.82) = 22 lb. Each component is 11,332 lb, and the resultant is 2 (11,332)=16,026\sqrt{2}\,(11{,}332) = 16{,}026 lb. Nearly all of it is pressure, so even with a valve shut downstream and the water stopped, the bend would need almost the same block. Mind the units: psi times in² gives pounds, but psi times ft² comes out 144 times too small.

The Handbook's FF is the same: the "force exerted by the bend on the fluid," with the fluid's force on the bend "equal in magnitude and opposite in sign." So find FF and reverse it. The water pushes this bend along the incoming flow and back against the outgoing flow, outward from the turn, which is why the thrust block goes on the outside. The block, holding the bend still, pushes back on it with FF itself, so the anchoring force has the same size as the water's push.

Use gauge pressures. The atmosphere presses all the way around the outside of the pipe too, and a pressure that's the same on every side pushes nowhere. The Handbook doesn't say, calling PP just the "internal pressure in the pipeline."

The vane's steps carry over, with one addition:

  1. Draw the control volume, cutting square across the pipe at each end.
  2. Point x along the incoming flow, with y toward the turn.
  3. Add a gauge pressure force PAPA at each cut, pointing in. A cut through a free jet gets none.
  4. Find the bend's push on the water from ΣF=ρQ(v2−v1)\Sigma F = \rho Q(v_2 - v_1) in each direction, then reverse it for the force on the pipe.

Bends at any angle

Most bends turn less than 90°. Let α\alpha be the angle the flow turns through, measured from its incoming direction, as for a vane. The inlet terms still lie along x. Both outlet terms lie along the outgoing pipe, P2A2P_2A_2 pointing back in and ρQv2\rho Qv_2 pointing onward, so both resolve with cos⁡α\cos\alpha along x and sin⁡α\sin\alpha along y:

Fx+P1A1−P2A2cos⁡α=ρQ(v2cos⁡α−v1)Fy−P2A2sin⁡α=ρQ(v2sin⁡α−0)\begin{aligned} F_x + P_1A_1 - P_2A_2\cos\alpha &= \rho Q(v_2\cos\alpha - v_1) \\[4pt] F_y - P_2A_2\sin\alpha &= \rho Q(v_2\sin\alpha - 0) \end{aligned}
α 1 2 v1 v2 P1A1 P2A2 P2A2 cos α P2A2 sin α x y
The outlet's pressure force, resolved along x and y

Solve each for the bend's push, reverse it, and combine the components into the resultant, Fx2+Fy2\sqrt{F_x^2 + F_y^2}. A bend that also changes diameter works the same way, with each section's own AA and vv. The Handbook prints this pair under Pipe Bends, Enlargements, and Contractions:

P1A1−P2A2cos⁡α−Fx=Qρ(v2cos⁡α−v1)Fy−W−P2A2sin⁡α=Qρ(v2sin⁡α−0)\begin{aligned} P_1A_1 - P_2A_2\cos\alpha - F_x &= Q\rho(v_2\cos\alpha - v_1) \\[4pt] F_y - W - P_2A_2\sin\alpha &= Q\rho(v_2\sin\alpha - 0) \end{aligned}

Its sketch draws FxF_x pointing upstream, as in its Fixed Blade case, hence the minus sign. Its bend turns upward in a vertical plane, so the water's weight WW enters the y equation; for a horizontal bend, drop it. Its α\alpha, measured from its horizontal inlet, is the same turning angle.

Worked Example A 60° bend with a head loss
1 of 3

A horizontal bend turns a 300 mm water line through 60°. It carries 0.20 m³/s, the pressure at its inlet is 200 kPa, and the head loss through the bend is 0.5 m. Find the components and the resultant of the force the water exerts on the bend.

Reducers: the pressures push against each other

Straighten the bend out to α=0\alpha = 0 and you have a reducer. Both pressure forces now lie along the pipe, pushing into the control volume from opposite ends, and the x equation is all there is:

Fx=ρQ(v2−v1)−P1A1+P2A2F_x = \rho Q(v_2 - v_1) - P_1A_1 + P_2A_2

Watch the two pressure forces fight. The upstream pressure acts on the bigger area and wins easily, while the water's speed-up asks for only a modest net push downstream. So FxF_x comes out negative: the reducer holds the water back, and the water pushes the reducer downstream just as hard. A sudden contraction gets the same control volume and the same equation.

1 2 v1 v2 P1A1 P2A2 force on water coupling 1 2 P2 = 0 v1 v2 P1A1 force on water reducer nozzle
Pressure forces on a reducer and a nozzle

Problems usually give only the upstream pressure. Find the downstream one first, by Bernoulli, or by the energy equation when a loss is stated, and then write the momentum equation.

Checkpoint

A horizontal reducer takes a water line from 12 in. to 6 in. It carries 4.0 ft³/s, and the pressure in the 12 in. pipe is 60 psi. Neglecting losses, what axial force does the water exert on the reducer?

lb

Nozzles: the outlet is open air

A nozzle is a reducer whose outlet is a free jet, and that changes one thing. At the tip the jet is surrounded by air, so its gauge pressure is zero, and the outlet's pressure force disappears, as in the right panel above:

Fx=ρQ(v2−v1)−P1A1F_x = \rho Q(v_2 - v_1) - P_1A_1

A problem often gives the flow and not the inlet pressure, and it doesn't need to. Write Bernoulli from the inlet to the jet, with P2=0P_2 = 0 and no change in height:

P1γ=v22−v122g\frac{P_1}{\gamma} = \frac{v_2^2 - v_1^2}{2g}

So a nozzle takes three equations in a row: continuity for the two velocities, Bernoulli for the inlet pressure, and momentum for the force. Given the pressure instead, run the same Bernoulli backward, with v1=v2(A2/A1)v_1 = v_2(A_2/A_1), for the velocities. The answer always points the same way. The inlet pressure pushes the water downstream harder than the speed-up needs, so the nozzle holds the water back, and the water pushes the nozzle downstream, as if to tear it off the hose. The coupling holds it on, in tension.

Worked Example The force on a fire-hose coupling
1 of 2

A fire hose with a 2.5 in. inside diameter ends in a nozzle with a 1 in. tip, discharging 0.40 ft³/s of water into the air. Find the force on the coupling that holds the nozzle to the hose.

Checking the setup

The arithmetic is only as good as the arrows. Before you calculate, check where each pressure force acts, which way it points, and whose force you're about to report.

Checkpoint
1 of 3

A horizontal 90° bend carries a steady flow of water. Which control volume shows the pressure forces on the water correctly?

A.
1 2 flow flow P1A1 P2A2
B.
1 2 flow flow P1A1 P2A2
C.
1 2 flow flow P1A1 P2A2
D.
1 2 flow flow P1A1

Recap

  • Water pushes on a fitting in two ways: by its pressure, PAPA at each cut, always pointing into the control volume, and by having its momentum changed. The fitting supplies whatever push the pressures leave over.
  • Write ΣF=ρQ(v2−v1)\Sigma F = \rho Q(v_2 - v_1) once per direction, with x along the incoming flow, the outlet terms resolved with cos⁡α\cos\alpha and sin⁡α\sin\alpha, and gauge pressures. Find the fitting's push on the water, then reverse it for the force on the pipe.
  • In a 90° bend, each component is PA+ρQvPA + \rho Qv. In a water main, the pressure part dwarfs the momentum part.
  • In a reducer, the pressures oppose: Fx=ρQ(v2−v1)−P1A1+P2A2F_x = \rho Q(v_2 - v_1) - P_1A_1 + P_2A_2, with P2P_2 from Bernoulli or the energy equation. The water pushes the reducer downstream.
  • At a nozzle's free jet, P2=0P_2 = 0. Continuity gives the velocities, Bernoulli the inlet pressure, and momentum the force, which pushes the nozzle downstream and puts the coupling in tension.