Back

Fluid Mechanics

  • Topic 8
  • 12 Lessons

Overview

Nearly every fluids problem in this topic, from a manometer reading to the force on a pipe bend, gets solved the same way. Pick two points, decide whether the fluid between them is at rest or moving, and write the balance that fits. There are only four balances to choose from. Still fluid needs only pressure with depth. Moving fluid conserves mass, which is continuity, and it conserves energy once you count what a pump adds and what friction takes. And when a question asks for the force a moving fluid exerts, that's momentum.

You can watch the decision flip in one tank. With its outlet valve shut, the water between point 1 on the surface and point 2 just behind the valve is at rest, and the pressure at point 2 is set by its depth alone, γh\gamma h. Open the valve, and the water flows. Move point 2 into the jet just outside the nozzle, at the same depth: its pressure is atmospheric, and the height hh shows up as speed instead. Put a plate in the jet, and holding it there takes a push.

Valve shut: at rest h pressure with depth 1 2 Valve open: moving F momentum h continuity and energy 1 2
One tank, with its valve shut and then open

At rest, only depth matters. Still water can't resist being sheared, so the only thing that sets the pressure at a point is the weight of the water stacked above it, P=γhP = \gamma h. The pressure on a tank's floor depends on the depth and the liquid, and not at all on whether the tank is a standpipe or a swimming pool. The still-water Lessons all build on this rule. A manometer applies it one column at a time, the force on a submerged surface is that pressure spread over its area, and buoyancy is the water pushing harder on a body's bottom than on its top.

Moving fluid conserves mass. Water can't pile up or vanish in a full pipe, so the same flow passes every section, Q=AvQ = Av, with vv the average velocity. Where a pipe narrows, the water has to speed up to get the same flow through. Turning a flow rate into velocities this way is the first step of nearly every flowing-water problem.

Energy is counted in heads. Every pound, or newton, of flowing water carries a pressure head, a velocity head, and an elevation head, each one a height of that water. Without friction, the three add up to the same total at both points. That's Bernoulli's equation, and it's why pressure drops wherever water speeds up in a level pipe. Real pipes lose head to friction as the water moves, and a pump is the only way to put head back, so the books get two more entries: the head a pump adds and the head lost along the way. Tanks, flow meters, pumps, and pipe friction all run on this one equation.

A force from moving fluid takes momentum. Changing a stream's velocity, even just its direction, takes a push, and the stream pushes back just as hard. A free jet is at atmospheric pressure all around, so it pushes on a plate by its change in momentum alone. Water turning through a pipe bend pushes in two ways, by its change in momentum and by the pressure at each end of the bend. The momentum Lessons come last for a reason: continuity supplies their velocities, and energy supplies their pressures.

Two properties feed the balances. How much a fluid weighs per unit volume, its specific weight γ\gamma, turns a depth into a pressure and a pressure into a head. How much it resists flowing, its viscosity, is where friction losses come from. Fluid Properties, the first Lesson below, sets up both.

The Handbook's Fluid Mechanics chapter prints all four balances: pressure with depth under Characteristics of a Static Liquid, continuity and energy under Principles of One-Dimensional Fluid Flow, and momentum under The Impulse-Momentum Principle. It doesn't tell you which one a problem needs. That's the habit: pick two points, then ask whether the fluid between them is still or moving, and whether you're after a force.

Checkpoint
1 of 4

A vertical gate at the foot of a dam holds back a reservoir 30 ft deep. Which balance gives the water's force on the gate?

A.
Pressure with depth
B.
Continuity
C.
Energy
D.
Momentum