The Cross Product
The cross product builds the one direction perpendicular to two others.
Before this Lesson
Put a wrench on a bolt and turn it counterclockwise, the way that loosens it. The handle lies flat, and your pull lies flat, both in one level plane. Yet the bolt moves in neither direction. It climbs straight up, square to both. Two arrows go in, and a third comes out. The arithmetic behind that third arrow also tells you which way a tilted panel faces and how big it is.
From Vectors and Components: a vector written as has the length , and is its unit vector. The arrow from one point to another is head minus tail. The dot product is , and zero means perpendicular.
Two arrows in, a third one out
Slide two vectors, and , tail to tail. Unless they're parallel, they pin down one flat plane. Their cross product, , is a new vector, and the rules for building it are short:
- Its line is perpendicular to that plane, which makes it perpendicular to both and .
- Its sense along that line comes from the right-hand rule. Point the fingers of your right hand along , curl them toward through the smaller angle, and your thumb points along . The Handbook names this rule without saying how it works.
- Its length is , where is the angle between them.
The sine looks arbitrary until you draw the parallelogram the two vectors span. Its base is . Its height is how far stands off that base, which is . Base times height is , so the cross product's length is the parallelogram's area. One arrow records both which way the plane faces and how much area the two vectors span.
The Handbook's Vectors section packs this into one line, with as the unit vector perpendicular to the plane of and :
What the picture already says
Three properties follow from the picture with no arithmetic at all.
- Perpendicular to both. The dot product of with either or is zero, which gives you a free check on any result.
- Order matters. Swap the vectors, and your fingers curl the other way. The thumb flips, and the length stays the same. The Handbook prints this as . The dot product didn't care about order, but this one does.
- Parallel vectors give zero. At 0° or 180°, , and the parallelogram collapses into a line with no area. The result is the zero vector. The Handbook's Identities list says that if , then , , or is parallel to .
Now try it on the axis arrows. and are each 1 long and 90° apart, so has a length of . Fingers along +x, curl toward +y, and your thumb points up +z. So . The Identities list prints the family:
There's nothing to memorize if you put the three on a circle. Cross two in forward order, and you get the third. Cross them in backward order, and you get its negative.
Determinants: one number from a square array
Computing a cross product from components takes one tool. A determinant is a square array of numbers between vertical bars, and the whole array stands for a single number. The Handbook's Determinants section calls the 2 × 2 kind second-order and the 3 × 3 kind third-order.
A 2 × 2 is one diagonal's product minus the other's, starting from the top left:
A 3 × 3 shrinks to three of those. Walk across the top row. For each entry, cross out its row and its column, and multiply the entry by the 2 × 2 that's left. The signs alternate: plus, minus, plus. The Handbook prints it this way, along with a six-term version you can ignore:
The minus sign in the middle belongs to the position, whatever sign the entry already has. Many approved calculators also evaluate determinants in a matrix mode, which makes a quick check.
The cross product from components
Multiply out , all nine products, as you did for the dot product. This time the outcome flips. Like with like vanishes, since , and the six mixed products survive, each with a sign from the circle. Collect them by unit vector:
Nobody memorizes that. Look at it, though: plus, minus, plus, and each bracket a 2 × 2. It's the 3 × 3 recipe, with the unit vectors as the top row. Arrows in the top row mean the result is a vector, not one number, so this is the recipe borrowed as a memory aid. It's also how the Handbook's Vectors section prints the cross product:
The first vector goes in the second row, and the second vector goes in the third. The minus sign on the term is the one people lose, and an exam's wrong answers count on it. When you finish, dot the result with either vector and look for zero. Many approved calculators also take cross products in a vector mode.
The unit normal: which way a plane faces
Return to the mast from Vectors and Components, and stretch a triangular tarp between its two cables. Wind pushes on fabric square to its face, so you want the direction straight out of the tarp, called its normal. None of its edges point that way, but any two of them lie in its plane, so cross them.
That gives the right line, but its length is whatever the area happened to be. You want direction alone, so divide by the length, as for any unit vector:
That's the Handbook's line from earlier, solved for . A plane has two faces, so is just as perpendicular, and produces it. When a question asks for a unit vector perpendicular to a plane, either one is correct.
Area: the length you divided away
The 109.2 you divided away wasn't waste. It's the area of the parallelogram the two edges span. A diagonal cuts any parallelogram into two identical triangles, so a triangle gets half:
So the tarp has an area of . This is the from Triangle Trigonometry, written in components, so you never need the angle. The Handbook doesn't mention this use: it never says that a cross product's length is an area.
Given three corners, make two edges leaving the same corner, each head minus tail. Any corner works.
Moments: why a wrench is a cross product
Back to the wrench, seen from above. Let run from the bolt's center to your hand, and pull with a force at an angle to the handle. Split that pull in two. The part along the handle, , tugs on the bolt and turns nothing. The part square to the handle, , does all the turning.
So the turning effect is , the length of , and that's where the sine comes from. The direction fits too: curl your fingers the way the bolt turns, and your thumb lies along its axis. The Handbook's Statics section, under Moments (Couples), defines a moment as this cross product and writes out its components, with , , and belonging to :
Order counts: gives the opposite moment. So does running backward. Its tail sits at the point you're taking the moment about, and its head lands on the force's line of action, the endless straight line the force acts along.
The head can land anywhere on that line. Slide it along, and changes only by a piece parallel to , and a parallel piece crossed with gives zero. In the figure, a longer meets the line at a shallower angle, and stays equal to the same perpendicular distance. The Handbook says only "from a point to the line of action," so pick whichever point makes the arithmetic easiest.
In a flat problem, with everything in the x-y plane, only survives, the component of . A positive value means counterclockwise, because with your thumb along +z, pointing at you, your fingers curl counterclockwise. Moments and Couples picks up from this form.