Area by Coordinates and Offsets
Walk the boundary, cross-multiply the coordinates, and the area falls out.
Before this Lesson
Picture a lot with five corners and not one right angle. You could chop it into triangles, but then each triangle needs a base and a height that nobody measured. If you have the corners' coordinates, you can skip all of that. Take them in order around the boundary, do ten multiplications and a subtraction, cut the result in half, and there's the area, whatever the shape. Later on, you'll also handle a boundary with no corners at all, like a stream bank.
Every side sweeps a trapezoid
Start with why this works, since the reason is short. Take a four-sided parcel with corners A (N 200, E 100), B (N 400, E 300), C (N 300, E 700), and D (N 100, E 400), in feet. Picture an axis along the line , south of everything, and walk the boundary clockwise. On each side, drop a line from both ends straight down to that axis. The side, the two drops, and the axis make a trapezoid, and a trapezoid's area is its width times its average height. With 1 as the end you leave and 2 as the end you reach:
The useful part is that the width has a sign. Along the north side of the parcel you're heading east, so is positive and the trapezoid adds. Coming back along the south side you're heading west, so it's negative and the trapezoid subtracts. The east-heading trapezoids cover the parcel and all the ground south of it, down to the axis. The west-heading ones cover only that ground. Add them up, the ground cancels, and the parcel is what's left.
| Side | Width, E₂ − E₁ (ft) | Average N (ft) | Signed area (ft²) |
|---|---|---|---|
| AB | +200 | 300 | +60,000 |
| BC | +400 | 350 | +140,000 |
| CD | −300 | 200 | −60,000 |
| DA | −300 | 150 | −45,000 |
| Total | 0 | 95,000 |
You could stop there, but averaging at every side is more work than you need. Multiply one side's trapezoid out:
The second fraction only involves each corner with itself: the far corner's minus the near corner's. Walk all the way around, and every corner is the far end of one side and the near end of the next, so those terms all cancel. Only the cross terms survive, and that's the coordinate area formula:
The sum closes back to the first corner. The absolute value is there because the sign only says which way you walked: clockwise gives a plus here, and counterclockwise a minus.
Cross-multiply down a stack
To run this by hand, stack the corners in order around the boundary, and write the first corner again at the bottom. That repeated row is the side that closes the loop, so leaving it off leaves out a side. Then multiply along the diagonals: each by the one row down, and each by the one row down. Total each set, subtract, and halve.
That's 470,000 − 280,000 = 190,000, and half of it is 95,000 ft², the same as the trapezoids. With real coordinates, the area is a small difference between two big totals, so keep every digit in your calculator until the end.
Questions usually want acres or hectares. The Handbook's Units and Conversion Factors page has both: an acre is 43,560 ft², and a hectare is m², or 10,000 m². So ABCD is 95,000 / 43,560 = 2.18 acres.
If the corners carry labels, such as 250.00 N, 180.00 W, make S and W negative first, as in Coordinate Geometry. The formula doesn't mind negative numbers.
The stack is only a layout, and the Handbook doesn't print it. Its Area formulas section gives the same result as Area by Coordinates, on one line in and :
Read as and as , and the subscript as the last corner, not a northing. Those are the same products grouped by corner: each easting times the difference of its neighbors' northings. For ABCD, 100(400 − 100) + 300(300 − 200) + 700(100 − 400) + 400(200 − 300) = −190,000, which halves to −95,000 ft². This form comes out negative on a clockwise walk, and the Handbook prints no absolute value, so drop the sign yourself. It takes half the multiplications, so use it if you prefer it.
When the corners come as moves
A traverse doesn't hand you positions. It hands you moves: latitudes and departures, or bearings and distances. So make the coordinates first, by the forward computation from Coordinate Geometry: each corner is the corner before it plus one course's move. With a bearing, the sizes are and , and the letters give the signs. Then stack the corners as usual.
A deed gives you even less. It starts at a physical marker, the point of beginning (POB), and reads as a walk: "thence N 40°15′ E, 350.00 ft," and so on, until the last course comes back to the POB. There isn't a coordinate anywhere in it, and the Handbook says nothing about deeds. You make the coordinates up.
Here's why that's allowed. Slide the whole parcel 1,000 ft north. Every trapezoid gets 1,000 ft taller, so each one changes by its width times 1,000. But a walk that ends where it began goes exactly as far west as it went east, so the widths total zero, and all that extra area totals zero too. Slide the parcel east instead, and the widths and heights don't change at all. Only the differences between coordinates matter.
So call the POB N 1,000, E 1,000, or whatever you like. The same fact shrinks ugly numbers: subtract one round number from every northing and another from every easting, and the products get smaller while the area stays put.
The list doesn't know the boundary
The formula trusts whatever order you feed it. A point table lists corners in whatever order suited the crew, and that may have nothing to do with the order around the boundary. So sketch it first, and take the order from the sketch.
This bites hardest on a parcel with a reentrant corner, one that points inward. In this table, the crew shot the outer corners first and the notch last.
| Point | N (ft) | E (ft) |
|---|---|---|
| 1 | 100 | 100 |
| 2 | 100 | 600 |
| 3 | 500 | 100 |
| 4 | 500 | 600 |
| 5 | 250 | 300 |
Around the boundary, the order is 1, 3, 5, 4, 2, and the formula gives 137,500 ft². You can check that one by eye: a 500 ft by 400 ft rectangle is 200,000 ft², and the notch is a triangle with a 500 ft base and a 250 ft height, 62,500 ft². The reentrant corner needs no special handling. The sides running into the notch still head east, but they sit lower, so their trapezoids add less, by exactly the notch.
In the table's order, the path crosses itself and the formula answers 2,500 ft². There's no error and no warning. The two loops of a crossed path have opposite signs, so they nearly cancel.
Carving off a right-of-way
A road or utility often needs a strip of a parcel, and the piece it acquires is the take. A right-of-way line marks it, cutting the parcel in two. Each piece is a polygon with a boundary you can walk, so you need nothing new, just the right list of corners. The two points where the line crosses the boundary are corners of both pieces. Sketch it first, then walk the piece you want: along the old boundary from one crossing point to the other, through every parcel corner on that side, then back along the right-of-way line.
For the area that remains, either walk that piece the same way, or subtract the take from the whole parcel.
When the boundary has no corners
A stream bank has no corners to list. So the crew runs a straight survey line beside it, and at a regular interval measures the perpendicular distance from the line to the bank. Those distances are offsets. Two neighboring offsets and the line between them make a strip. Pretend the bank runs straight across the top of each strip, and every strip is a trapezoid: times the average of its two offsets.
Now add the strips. An interior offset belongs to two strips, at half weight in each, so it counts once. An end offset belongs to only one, so it counts for half. That's the Trapezoidal Rule in the Handbook's Area formulas section, which calls the common interval:
For the bank in the figure, that's 20[(6 + 8)/2 + 20 + 26 + 22] = 20(75) = 1,500 ft².
Simpson's rule bends the top
A real bank curves, and those straight tops cut across every bend. Simpson's 1/3 rule fits a parabola through each set of three offsets instead. One parabola spans two intervals, so the intervals have to come in pairs. That means an even number of intervals, which means an odd number of offsets. The Handbook's Area formulas section puts it as "n must be odd number of measurements." Its Mathematics pages print the same rule under Numerical Integration, where counts intervals and must be even. It's the same requirement, counted two ways.
Over one pair of intervals, the area under the parabola works out to . Where two pairs meet, the shared offset picks up a 1 from each, so it counts 2. So the weights run 1, 4, 2, 4, 2, ..., 4, 1, all times . The Handbook writes that as:
For the same bank, that's (20/3)[6 + 4(20) + 2(26) + 4(22) + 8] = (20/3)(234) = 1,560 ft².
Five measurements, two areas, and neither is a mistake. The offsets say nothing about the bank between them, so each rule has to guess: straight lines or parabolas. This bank bulges away from the survey line, so the straight tops cut inside the curve and the trapezoids come up short. On a perfectly straight boundary, the two would agree. Simpson's follows a curved boundary more closely, so it's the better choice whenever the count of offsets allows it.
Unequal intervals: back to the trapezoid
Both formulas have a common interval built in. Crews don't always keep one: along a lake shore, they tend to take an offset wherever the shore bends. The Handbook prints nothing for that case, and you don't need it to. Each strip is still a trapezoid, and now each has its own width :
Notes usually give each offset's distance along the line, so subtract neighbors to get the widths.