Manometers

Walk through the manometer, adding as you go down and subtracting as you go up.

Before this Lesson

Say you need the pressure in a water main, and all you have is a clear tube and a tape measure. Tap the main, run the tube straight up, and the water climbs until its weight balances the pressure in the pipe. Measure the height, multiply by γ\gamma, and you're done.

One catch: at 40 psi, the water climbs 92 ft. So bend the tube into a U and put mercury in the bottom. It's 13.6 times heavier than water, so the same pressure holds it under 7 ft high. Now the tube holds two liquids, and reading it takes a rule you already know, used one leg at a time.

A walk through the tube

A manometer is just fluids at rest in a tube, so the rules from Pressure and Depth work inside it:

  • Go down a height hh through a fluid, and the pressure rises by γh\gamma h.
  • Go up hh, and it falls by γh\gamma h.
  • Go sideways within one continuous fluid, and it doesn't change.

That's the Handbook's Pressure Field in a Static Liquid, P2−P1=−γ(z2−z1)P_2 - P_1 = -\gamma(z_2 - z_1), cut into steps. Start where you know the pressure, usually an open end at zero gauge, and walk through the tube to the point you want, giving each leg its own γ=SG γw\gamma = SG\,\gamma_w.

The simplest manometer is the hook's tube, a piezometer: open at the top and tapped into a pipe or tank. Walk down from the open surface to a point a height hh below it, and P=γhP = \gamma h. It suits liquids at low pressures; a gas would blow straight out the top.

For more pressure, or for a gas, use a U with a heavier gauge fluid in the bottom. The Handbook draws this simple manometer under Manometers: fluid 1 fills the vessel and the top of the left leg, and the gauge fluid, fluid 2, fills the bend and stands in the open right leg.

P0 h1 h2 fluid 1, γ1 fluid 2, γ2 P2 P1 1 2 3
The Handbook's simple manometer, read as a walk

Adapted from the FE Reference Handbook, Manometers

Walk from the open surface, where the pressure is P2P_2:

  1. Down h2h_2 through fluid 2 to the interface's level: add γ2h2\gamma_2 h_2.
  2. Across that level to the interface, P1P_1. The path stays in fluid 2, around the bend, so nothing changes.
  3. Up h1h_1 through fluid 1 to the tap: subtract γ1h1\gamma_1 h_1.

That lands on the Handbook's equation:

P0=P2+γ2h2−γ1h1P_0 = P_2 + \gamma_2 h_2 - \gamma_1 h_1

With the right leg open to the air, P2=0P_2 = 0 gauge. Write each leg's sign as you take the step, not at the end, and put every height in feet or meters first, since γ\gamma is per cubic foot or meter: a 16 in. reading is 1.333 ft.

If the vessel holds a gas, fluid 1 is about 800 times lighter than water, so its leg drops out: P0=γ2hP_0 = \gamma_2 h, with hh the difference in level between the gauge fluid's two surfaces. A leg of water or oil always counts.

Worked Example A mercury U-tube on a water pipe
1 of 3

A mercury manometer is tapped into a water pipe, as in the Handbook's figure. The mercury in the open leg stands 16 in. above the mercury-water interface, and the pipe's centerline is 10 in. above the interface. Find the gauge pressure at the centerline.

Between two points

A differential manometer has no open end. Each leg connects to a different point, so the walk runs from one point to the other and gives the difference in their pressures. The difference in level between the two surfaces of the gauge fluid is the manometer's deflection, or reading.

The most common case has two taps at one elevation on a water pipe, here on either side of a valve, with mercury below.

flow y h a b c d 1 2 water mercury
A mercury differential manometer across a valve

Walk from tap 1 down through the water to aa, across the mercury to bb, up hh of mercury to dd, and up through the water to tap 2:

P1+γw(y+h)−γmh−γwy=P2⟹P1−P2=(γm−γw)hP_1 + \gamma_w(y + h) - \gamma_m h - \gamma_w y = P_2 \quad\Longrightarrow\quad P_1 - P_2 = (\gamma_m - \gamma_w)h

The distance yy cancels, so it never matters how far below the pipe the mercury sits. Over the stretch hh between the mercury levels, leg 1 holds water and leg 2 holds mercury; everywhere else the legs match and cancel. So the pressure difference only pays for mercury being heavier than water: γm−γw=12.6γw\gamma_m - \gamma_w = 12.6\gamma_w, not 13.6γw13.6\gamma_w. The Handbook's simple manometer has the same special case: with h1=h2=hh_1 = h_2 = h, P0=P2+(γ2−γ1)hP_0 = P_2 + (\gamma_2 - \gamma_1)h, and it notes that the difference between the two densities is used.

When the points sit at different elevations, or the lines carry different fluids, the legs no longer match. There's no shortcut: walk every leg with its own γ\gamma.

Worked Example Two pipes, two fluids
1 of 3

Pipe A carries water. Pipe B, higher up, carries oil with SG=0.85SG = 0.85. A mercury manometer joins them as shown. Find PA−PBP_A - P_B.

0.60 m 0.25 m 1.10 m A B water oil, SG = 0.85 mercury, SG = 13.6
A mercury manometer between a water pipe and an oil pipe

Reading the levels

Some questions skip the numbers and ask you to read a manometer by eye.

Which side is at the higher pressure? The gauge fluid gets shoved away from the higher pressure, so with mercury below the pipe, it stands lower in the leg that's pushed harder. In the differential manometer above, the mercury is pushed down in leg 1, and both legs hold water up to taps at one level, so P1>P2P_1 > P_2. When the legs hold different fluids or the taps sit at different heights, the eye can be fooled. Walk it, and the sign settles it.

Which points share a pressure? Two points do only when they're at one level and joined by a path that stays in one fluid. In the figure, aa and bb qualify: the mercury runs unbroken between them through the bend. cc and dd are level too, but climbing to them from aa and bb, leg 1 rises through water and loses only γwh\gamma_w h, while leg 2 rises through mercury and loses γmh\gamma_m h. So Pc>PdP_c > P_d. A level line carried across an interface into another fluid is the most common way to wreck a walk.

How does the gauge fluid change the reading? Solve for the deflection, h=(P1−P2)/(γm−γw)h = (P_1 - P_2)/(\gamma_m - \gamma_w). A heavier gauge fluid balances the same difference with a shorter column, and what counts across a water line is how much heavier than water it is. A 1 psi difference moves mercury, which outweighs water by 12.6γw12.6\gamma_w, only 2.2 in. A gauge fluid with SG 2.0 outweighs it by just γw\gamma_w, so the same 1 psi moves it 2.3 ft. The closer the gauge fluid's weight is to the line liquid's, the larger the reading: mercury suits large differences, and a fluid nearer water's weight suits small ones.

Checkpoint
1 of 2
1 2 3 4 water open to air mercury
A mercury U-tube on a water pipe, open on the right

The U-tube's right leg is open to the air. Point 1 is at the mercury-water interface in the left leg, and point 2 is in the right leg at the same level. Point 4 is at the mercury's open surface, and point 3 is in the left leg at the same level. Which statements are true?

A.
P1=P2P_1 = P_2
B.
P3=P4P_3 = P_4
C.
Point 3 is below atmospheric pressure, since it's in the leg connected to the pipe
D.
The water in the pipe is below atmospheric pressure

Working backward

Every walk ends in one equation, and nothing says the unknown has to be the pressure. Given a pressure, solve for the deflection, as above. Given a pressure and a reading, solve for the gauge fluid's γ\gamma, then divide by γw\gamma_w for its SG. Say an open U-tube on a tank of air at 12 kPa shows a 0.80 m difference in levels of an unknown liquid. The air drops out, so γ=12/0.80=15.0\gamma = 12/0.80 = 15.0 kN/m³, and SG=15.0/9.81=1.53SG = 15.0/9.81 = 1.53.

Checkpoint
1 of 2

A mercury differential manometer will span two taps at one elevation on a water pipe, where the pressure difference is expected to be 4.0 psi. What deflection will it show?

in.

Upside down: the inverted U-tube

For small differences in a liquid line, flip the U over. An inverted U-tube rises above the pipe, with a light fluid trapped in its top: air, or an oil lighter than the liquid in the line. The high pressure still shoves the gauge fluid, the air or oil, away, which here means up, so the water climbs higher on the high-pressure side.

flow h 1 2 water air or oil
An inverted U-tube across the same valve

Walk from tap 1 up its water column, across the top, and down the other column to tap 2. Air weighs next to nothing, so it presses equally on both water surfaces, and the columns differ by hh: P1−P2=γwhP_1 - P_2 = \gamma_w h.

With oil on top, the oil fills the stretch hh in leg 2, between the two water levels, and it has weight. Walking down through it adds γoilh\gamma_{\text{oil}}h back:

P1−P2=(γw−γoil)hP_1 - P_2 = (\gamma_w - \gamma_{\text{oil}})h

It's the difference of densities again, with the lighter fluid on top. Don't drop the oil as if it were air: it weighs 80 to 90 percent as much as water, which is also why oil reads more than air for the same difference.

Checkpoint
1 of 2

An inverted U-tube with air in its top spans two taps at one elevation on a water pipe. The water stands 320 mm higher in one leg than in the other. What is the pressure difference between the taps?

kPa

Taps at different heights

On a sloping or vertical pipe, the taps sit at different elevations, z1z_1 and z2z_2, above any datum. Let the mercury in leg 1 sit a distance yy below tap 1, and walk from tap 1 to tap 2:

flow y h datum z1 z2 1 2 water mercury P1/γ + z1 P2/γ + z2 h(SGm/SGw − 1)
A mercury differential manometer on a sloping water pipe
P1+γwy−γmh−γw(y−h+z2−z1)=P2P_1 + \gamma_w y - \gamma_m h - \gamma_w(y - h + z_2 - z_1) = P_2
P1−P2=(γm−γw)h+γw(z2−z1)P_1 - P_2 = (\gamma_m - \gamma_w)h + \gamma_w(z_2 - z_1)

yy cancels again, but the taps' rise, z2−z1z_2 - z_1, adds a column of water to leg 2 that stays in the answer. On a level pipe, z2=z1z_2 = z_1, and this is (γm−γw)h(\gamma_m - \gamma_w)h from before.

Now divide by γw\gamma_w and move the elevations to the left. Written for any liquid in the line, with γ\gamma and SGwSG_w its specific weight and specific gravity:

(P1γ+z1)−(P2γ+z2)=h(SGmSGw−1)\left(\frac{P_1}{\gamma} + z_1\right) - \left(\frac{P_2}{\gamma} + z_2\right) = h\left(\frac{SG_m}{SG_w} - 1\right)

Each bracket is a pressure head plus an elevation: the piezometric head, P/γ+zP/\gamma + z. It's the elevation the water would climb to in a piezometer at that point, drawn dashed in the figure. The Handbook doesn't name it, but its Hydraulic Gradient entry pictures the same thing: a row of piezometers along a pipe, with the grade line joining their water levels. The manometer compares two of those levels, so its deflection gives the piezometric-head difference directly, whatever the pipe's slope.

For water, SGw=1SG_w = 1, and mercury's factor is 12.6. The Handbook doesn't print the factor, but its venturi and orifice equations carry the same grouping, P1/γ+z1−P2/γ−z2P_1/\gamma + z_1 - P_2/\gamma - z_2, which is where it returns in Venturi Meters, Orifice Plates, and Pitot Tubes. Read which difference a question asks for: the head difference comes straight from the deflection, and the pressure difference keeps the water column.

Worked Example A vertical pipe
1 of 3

Water flows up a vertical pipe. Tap 2 is 1.5 m above tap 1, and a mercury differential manometer between them reads 180 mm, with the mercury lower in tap 1's leg. Find the piezometric-head difference and the pressure difference between the taps.

Recap

  • Walk through a manometer one leg at a time: down adds γh\gamma h, up subtracts it, and sideways within one continuous fluid changes nothing. Each leg takes its own γ=SG γw\gamma = SG\,\gamma_w, with heights in feet or meters.
  • A piezometer reads P=γhP = \gamma h, and an open U-tube P0=P2+γ2h2−γ1h1P_0 = P_2 + \gamma_2 h_2 - \gamma_1 h_1. A gas leg drops out; water and oil legs never do.
  • Across taps at one level, the difference of specific weights does the work: (γm−γw)h(\gamma_m - \gamma_w)h with mercury below, γwh\gamma_w h with air above, and (γw−γoil)h(\gamma_w - \gamma_{\text{oil}})h with oil above.
  • Points share a pressure only at one level in one continuous fluid. The gauge fluid is shoved away from the higher pressure, and the closer its weight is to the line liquid's, the more it reads.
  • Between taps at different heights, the deflection gives the piezometric-head difference, h(SGm/SGw−1)h(SG_m/SG_w - 1). For the pressure difference, add the rise z2−z1z_2 - z_1 and multiply by γw\gamma_w.