Pressure and Depth

Pressure depends only on how deep you are, not on the shape of the container.

Before this Lesson

Swim to the bottom of a pool's deep end, 8 ft down, and your ears start to ache. Now swim 8 ft down in a lake that runs past the horizon, with millions of tons of water around you. Your ears ache exactly the same.

All that extra water makes no difference. What your eardrums feel, about 3.5 psi more than at the surface, is set by how far down you are and what you're swimming in. That comes straight from the one thing a liquid at rest can't do.

The weight of the water above

Pressure is force per unit area, and in a liquid at rest it pushes the same amount in every direction, always squarely against whatever surface it meets. That's because a liquid can't resist shear. Push sideways on a block of steel and it pushes back. Push sideways on still water and it just flows, until nothing inside it pushes unevenly. A settled liquid has nothing left in it but pressure, pressing equally all around.

So what sets the size of that pressure? Picture a slim vertical column of water standing on a small patch of area AA, a depth hh below the surface. Its volume is AhAh, so it weighs γAh\gamma Ah. The water around it pushes only sideways, which can't hold up a weight, so the patch carries the whole column:

P=γAhA=γhP = \frac{\gamma A h}{A} = \gamma h

This is the water's own share. Anything pressing on the surface adds to it, as you'll see below. It grows in a straight line with depth. For water, each foot adds 62.4 lbf/ft², which is 0.433 psi after dividing by 144 in²/ft², and each meter adds 9.81 kPa. At the bottom of the 8 ft deep end, P=8(0.433)=3.5 psiP = 8(0.433) = 3.5\ \text{psi}.

The Handbook states the rule between any two points, under The Pressure Field in a Static Liquid:

P2−P1=−γ(z2−z1)=−γhP_2 - P_1 = -\gamma(z_2 - z_1) = -\gamma h

Here zz is elevation, measured upward, with point 2 a height hh above point 1, so climbing lowers the pressure. Put point 2 at the free surface, and you're back to P1=γhP_1 = \gamma h.

Same depth, same pressure

The column picture needs open water straight above the point. For a point under a ledge, here's a sturdier argument.

Take a horizontal tube of water anywhere in a still liquid. Gravity pulls straight down, so the only sideways forces on the tube are the pressures on its two ends, and since it isn't moving, they balance. Moving sideways through a liquid at rest doesn't change the pressure. Moving down raises it by γ\gamma times the distance.

So get from the surface to any point by a staircase of vertical and horizontal steps inside the liquid. Only the vertical steps count, and they add up to the point's depth. The pressure is γh\gamma h whatever the container's shape, and all points at one elevation in one continuous liquid at rest share a pressure.

same water level h A B C D PA = PB = PC = PD = γh
Four connected vessels, one water level

This is the classic hydrostatic paradox: the flaring cone holds far more water than the slim tube, yet their bottoms feel the same pressure. The cone's extra water rests on its sloping walls. In the vessel that narrows, the walls press down on the water beneath them, and the floor feels that push as if a full-width column stood above it.

The staircase has to stay inside one continuous liquid. A point at the same level in a separate tank, or in a different liquid, follows its own column.

Multiplying force with a liquid

Equal pressure at equal elevation is the whole idea behind a hydraulic jack or press. Push the small piston down with a force F1F_1, and the oil under it is at P=F1/A1P = F_1/A_1. The large piston's face sits at the same elevation in the same oil, so it feels the same pressure over a larger area:

oil same elevation, same P F1 F2 D1 D2
A hydraulic jack
F1A1=F2A2⟹F2=F1A2A1=F1(D2D1)2\frac{F_1}{A_1} = \frac{F_2}{A_2} \quad\Longrightarrow\quad F_2 = F_1\frac{A_2}{A_1} = F_1\left(\frac{D_2}{D_1}\right)^2

Area grows as the square of the diameter, so a large piston three times the small one's diameter lifts nine times the force: 100 lbf in, 900 lbf out. It isn't free. The oil pushed out of the small cylinder has to fill the large one, so the small piston travels 9 in. for every inch the load rises, and the work in matches the work out, as with a lever. The Handbook doesn't cover jacks, but this one rule is all they take.

Checkpoint
1 of 2

A hydraulic press has a small piston 1.5 in. in diameter and a large piston 9 in. in diameter, with their faces at the same elevation. What load can a 60 lbf push on the small piston lift?

lbf

Gauge, absolute, and vacuum pressure

So far, the surface has been at zero pressure. It isn't. You live at the bottom of an ocean of air, which presses about 14.7 psi, or 101.3 kPa, on everything at sea level. The Handbook's conversion table lists the standard atmosphere as 14.70 psia and 1.013 × 10⁵ Pa. Higher up, there's less air overhead, so a problem may give a local barometer reading instead.

The atmosphere presses on everything, so it usually cancels, and most problems leave it out. A pressure measured from atmospheric is a gauge pressure, since an ordinary gauge open to the air reads zero. One measured from a perfect vacuum is an absolute pressure. Below atmospheric, a gauge gives a vacuum reading, which counts down from atmospheric. The Handbook's static-liquid section relates them in words:

Pabs=Patm+PgaugePabs=Patm−PvacP_{\text{abs}} = P_{\text{atm}} + P_{\text{gauge}} \qquad\qquad P_{\text{abs}} = P_{\text{atm}} - P_{\text{vac}}
absolute zero (perfect vacuum) atmospheric pressure 14.7 psia = 101.3 kPa abs A B Pabs Pgauge Pabs Pvac
Absolute, gauge, and vacuum pressure

At sea level, a vacuum reading of 4 psi is a gauge pressure of −4 psi, or 14.7−4=10.714.7 - 4 = 10.7 psia. Absolute pressure can't go below zero. Label absolute pressures as psia or kPa abs. In this topic, an unlabeled pressure is gauge.

Checkpoint
1 of 2
same level water oil A B C D
A closed tank with a standpipe, beside a jar of oil

The tank is full of water, which rises partway up its open standpipe. The separate jar holds oil with SG=0.85SG = 0.85, with its surface at the same level as the water in the standpipe. Points A, B, and C are at one elevation. Which statements are true?

A.
PA=PBP_A = P_B
B.
PC=PBP_C = P_B, since both points are the same depth below a free surface
C.
PD>PBP_D > P_B
D.
Widening the tank, with the same water level in the standpipe, would raise the pressure at D

Layers, one at a time

Real tanks are often layered: oil floating on water, perhaps with compressed air above it in a closed tank. Start at the top, with whatever pressure presses on the liquid's surface, and walk down, adding γh\gamma h for each layer, each with its own γ\gamma and its own thickness:

P=Pair+γoilhoil+γwhwP = P_{\text{air}} + \gamma_{\text{oil}}h_{\text{oil}} + \gamma_w h_w

Air is about 800 times lighter than water, so over a tank's height its weight doesn't count: its pressure is the same throughout the air space, and the liquid passes it on to every depth.

air at Pair oil, γoil water, γw hoil hw 1 2 depth 0 Pair P1 P2 γoil hoil γw hw P (gauge)
Pressure through air, oil, and water

In the graph, each layer is a straight line, gaining pressure faster in the heavier water. Two habits keep it right: measure how far a point sits into its layer down from that layer's top, never up from the floor, and give each layer its own γ\gamma. For an absolute pressure, add the atmosphere once, at the end. The same walk reads the tubes in Manometers.

Worked Example Air, oil, and water in one tank
1 of 3

A closed tank holds 3 m of water under a 2 m layer of oil with SG=0.80SG = 0.80. The air above the oil is at 30 kPa gauge. Find the gauge and absolute pressures at the tank's floor.

Pressure as a height of liquid

Turn P=γhP = \gamma h around, and any pressure becomes a height: the column of some liquid it would hold up.

h=Pγh = \frac{P}{\gamma}

That height is the pressure head, and it always belongs to a named liquid. One psi is 144 lbf/ft², and 144/62.4=2.31144/62.4 = 2.31, so 1 psi holds up 2.31 ft of water. The Handbook's conversion table prints 2.307. That table never names mercury's specific gravity, but it gives 1 in. of mercury as 13.60 in. of water, and that ratio is the SG. So the same pressure holds up a mercury column 13.6 times shorter.

That's why barometers use mercury. Stand a closed-end tube of mercury upside down in a dish, and the column drops until the atmosphere pressing on the dish holds up what's left: 29.92 in., or 760 mm. The space above holds only a trace of mercury vapor, so Patm=γHghP_{\text{atm}} = \gamma_{\text{Hg}}h. The Handbook draws this simple barometer under Manometers, keeping the vapor pressure in: Patm=Pv+γhP_{\text{atm}} = P_v + \gamma h. A water barometer would need a tube 33.9 ft tall.

Patm mercury Patm water 29.92 in. = 760 mm 33.9 ft = 10.3 m near-vacuum 6 ft
One atmosphere, two columns, to scale

Source: column heights from FE Reference Handbook, Units and Conversion Factors

One trap: a tank's air pressure turned into a head. Air at 10 psi above water is worth 10(2.31)=23.110(2.31) = 23.1 ft of water, because the question is how tall a column of water it would hold up. Dividing by air's γ\gamma gives a column of air thousands of feet tall, which nobody asked about.

Pressure head returns in Continuity and Bernoulli's Equation as P/γP/\gamma, one of the heads in Bernoulli's equation.

Checkpoint
1 of 3

A pressure gauge on a water main reads 65 psi. What is the pressure head, in feet of water?

ft

Recap

  • In a liquid at rest, pressure pushes equally in every direction and equals the weight of liquid above per unit area, P=γhP = \gamma h: 0.433 psi per foot or 9.81 kPa per meter of water.
  • Only depth and the liquid matter, not the container's shape. Points at one elevation in one continuous liquid at rest share a pressure, so a jack's pistons give F2/F1=A2/A1=(D2/D1)2F_2/F_1 = A_2/A_1 = (D_2/D_1)^2.
  • Gauge is the default. Pabs=Patm+Pgauge=Patm−PvacP_{\text{abs}} = P_{\text{atm}} + P_{\text{gauge}} = P_{\text{atm}} - P_{\text{vac}}, and the standard atmosphere is 14.7 psi or 101.3 kPa.
  • Through layers, start from the pressure on top and add each layer's own γh\gamma h.
  • Pressure head h=P/γh = P/\gamma is a height of a named liquid: 1 psi is 2.31 ft of water, and 1 atm is 33.9 ft of water or 760 mm of mercury (SG 13.6).