Hydrostatic Force on Plane Surfaces

Water pushes hardest at the bottom of a gate, so the resultant acts below the centroid.

A square hatch, 4 ft on a side, is set in the vertical wall of a water tank, its top edge 6 ft below the surface. You want to hold it shut with one prop on its dry side. How hard must the prop push, and where?

Prop it at the center, and the hatch pivots, its bottom swinging out, because the water down there pushes harder. The right spot is a little lower, and two short calculations place it to the inch.

The average pressure is the pressure at the centroid

From Pressure and Depth, the pressure at a depth hh is P=γhP = \gamma h, pushing squarely against whatever surface it meets. At the hatch's top edge, 6 ft down, that's 62.4(6)=37462.4(6) = 374 lbf/ft², and at its bottom edge, 10 ft down, 624 lbf/ft², growing in a straight line between them. Draw an arrow for the pressure at each depth, and the arrows trace out a trapezoid, the hatch's pressure diagram.

PC = 499 lbf/ft² 374 lbf/ft² 624 lbf/ft² C 6 ft 4 ft hC = 8 ft
Water pressure on the hatch
The hatch is 4 ft wide, into the page. The dashed line is a uniform pressure equal to the pressure at the centroid, CC.

The atmosphere presses on the water, and so on the hatch, but it presses just as hard on the dry side, so it cancels. Work in gauge pressure.

To total the push, slice the hatch into thin horizontal strips. A strip at depth hh with area dAdA carries a force γh dA\gamma h\,dA. Add them all. Each bit of area times its depth, summed, is the area times the centroid's depth:

F=∫γh dA=γhCA=PCAPC=γhCF = \int \gamma h\,dA = \gamma h_C A = P_C A \qquad P_C = \gamma h_C

The pressure at the centroid is the average pressure, and the force is that average times the area. Pressure grows in a straight line with depth, so the strips below the centroid gain exactly what the strips above it lose. That's the dashed line in the figure: a uniform 499 lbf/ft² over the whole hatch pushes as hard as the trapezoid. Nothing here depends on the hatch's shape.

The Handbook gives this force under Forces on Submerged Surfaces and the Center of Pressure, in a form you'll meet once the surface tilts. For the hatch:

F=62.4(8)(16)=7,990 lbfF = 62.4(8)(16) = 7{,}990\ \text{lbf}

That's about 4 tons, from water 10 ft deep at the hatch's bottom edge.

Checkpoint
1 of 2

A vertical rectangular gate 5 ft wide and 3 ft tall closes an opening in a tank wall. Its top edge is 8 ft below the water surface. What is the resultant water force on the gate?

lbf

Why the push lands below the centroid

Where does that single push act? Not at the centroid. The strips near the bottom push harder, so the resultant shifts down toward them, the way a triangular load's resultant shifts toward its tall end in Distributed Loads. The point where it acts is the center of pressure, CPCP.

Measure a distance yy along the hatch's plane from the line where that plane meets the water surface. On a vertical surface, yy is just the depth. The single force must twist the hatch exactly as the strips do, so match their moments about the surface line. A strip at yy pushes with γy dA\gamma y\,dA on a lever arm yy:

F yCP=∫y (γy dA)=γ∫y2 dA=γ(IxC+yC2A)F\,y_{CP} = \int y\,(\gamma y\,dA) = \gamma\int y^2\,dA = \gamma\left(I_{xC} + y_C^2 A\right)

Distance counts twice, once in the push and once in the lever arm, as in a moment of inertia. Divide by F=γyCAF = \gamma y_C A:

yCP=yC+IxCyCAy_{CP} = y_C + \frac{I_{xC}}{y_C A}

That's the Handbook's formula, with yCy_C and yCPy_{CP} as slant distances from the liquid surface and IxCI_{xC} about the centroidal axis parallel to the surface. The second term is the offset below the centroid, and it can't be negative. For a rectangle of height LL, the width cancels:

yCP−yC=bL3/12yC bL=L212 yCy_{CP} - y_C = \frac{bL^3/12}{y_C\,bL} = \frac{L^2}{12\,y_C}

For the hatch, that's 16/[12(8)]=0.16716/[12(8)] = 0.167 ft, or 2 in. Prop it 2 in below the center with 7,990 lbf, and it stays put.

With yCy_C underneath, the offset shrinks as the hatch goes deeper. At the surface, the diagram is a triangle, and the offset is a sixth of the height. Farther down, every strip carries the water above the hatch plus a little more, so the diagram looks more and more like a rectangle, whose resultant would sit right at the centroid.

0 250 lbf/ft² C CP e = 8.0 in Top edge at the surface 250 lbf/ft² 499 lbf/ft² C CP e = 2.7 in 4 ft Top edge 4 ft down 998 lbf/ft² 1,248 lbf/ft² C CP e = 0.9 in 16 ft Top edge 16 ft down
One 4 ft gate at three depths
Each pressure diagram is drawn to the same width at the bottom, so their shapes compare. The offset ee falls from 8.0 in to 2.7 in to 0.9 in.
Worked Example Force and center of pressure on a vertical gate
1 of 2

A vertical gate 1.5 m wide and 2.0 m tall has its top edge 1.0 m below the water surface. Find the resultant water force on it and how far below the surface it acts.

A wall that reaches the surface

A dam face or tank wall usually holds water right up to the surface, and the question is the force on a 1 ft or 1 m wide strip of it. With water HH deep, the pressure diagram is a triangle, from zero at the surface to γH\gamma H at the base.

γH F = γH2/2 H/3 H
Water against a vertical wall
The force is for one unit of the wall's width, into the page.

The force is the triangle's area, 12(γH)(H)\tfrac12(\gamma H)(H), acting through its centroid, a third of the way up from the base: the triangular-load rule. The general formula agrees. With yC=H/2y_C = H/2, the offset is H2/[12(H/2)]=H/6H^2/[12(H/2)] = H/6, so yCP=2H/3y_{CP} = 2H/3 below the surface, or H/3H/3 above the base.

F=γH22 per unit width, acting H3 above the baseF = \frac{\gamma H^2}{2}\ \text{per unit width, acting } \frac{H}{3} \text{ above the base}

The Handbook's Fluid Mechanics chapter doesn't print this shortcut, but it's just PCAP_C A with hC=H/2h_C = H/2 and A=HA = H. Measure the third up from the base, and use the shortcut only when the wetted surface starts at the water line. For a gate whose top is under water, go back to PCAP_C A. The same triangle returns behind retaining walls in Earth Pressure with Water and Surcharge.

Checkpoint
1 of 2

A concrete dam holds 12 m of water against its vertical upstream face. What is the horizontal water force per meter of dam, and where does it act?

A.
706 kN/m, 8 m above the base
B.
1,413 kN/m, 4 m above the base
C.
706 kN/m, 4 m above the base
D.
706 kN/m, 6 m above the base

Tilted surfaces: slope for geometry, depth for pressure

Now tilt the surface, as on the sloping upstream face of an earth dam. This is the case the Handbook draws. The plane makes an angle θ\theta with the liquid surface, and yy runs down the slope from OO, where the plane, extended if need be, meets the surface.

LIQUID y O θ FR yC yCP hC C CP
A submerged plane surface, seen edge-on

Adapted from the FE Reference Handbook, Forces on Submerged Surfaces and the Center of Pressure

Pressure still follows vertical depth, and a point yy down the slope is h=ysin⁡θh = y\sin\theta deep. So the force changes in only one way: the centroid's depth comes from its slant distance, which the Handbook lists as yC=hC/sin⁡θy_C = h_C/\sin\theta.

hC=yCsin⁡θF=PCA=γhCAh_C = y_C\sin\theta \qquad F = P_C A = \gamma h_C A

The Handbook writes the force, with the atmosphere on both sides, as FR,net=(ρg yCsin⁡θ)AF_{R,\text{net}} = (\rho g\,y_C\sin\theta)A. Since ρg\rho g is γ\gamma, that's the same γhCA\gamma h_C A, and on a vertical surface, θ=90∘\theta = 90^\circ makes yCy_C and hCh_C one and the same.

In the moment match, each strip's push picks up a sin⁡θ\sin\theta, and so does the total force, so it cancels. yCP=yC+IxC/(yCA)y_{CP} = y_C + I_{xC}/(y_C A) is unchanged, with every distance along the slope, and for a rectangle, LL is its length down the slope. The answer is a slant distance too. For the center of pressure's vertical depth, multiply by sin⁡θ\sin\theta at the end.

The usual stumble is where yy starts: at the water surface, not at the gate's top edge. A top edge a vertical depth dd below the surface is d/sin⁡θd/\sin\theta down the slope.

Worked Example A gate in a sloping dam face
1 of 3

A rectangular gate 1.5 m wide and 2.0 m long, measured down the slope, is set in a dam face sloping at 60° from the horizontal. Its top edge is 3.0 m below the water surface, measured vertically. Find the resultant water force and where it acts along the slope.

2.0 m 3.0 m 60° Gate width 1.5 m (into the page)
A gate in a 60° dam face

What changes the force, and what doesn't

Some questions skip the arithmetic and ask what happens when something changes. Read the answer off the two formulas. In F=γhCAF = \gamma h_C A, two things can change, the centroid's depth and the wetted area, so ask which of them a change touches. The offset, IxC/(yCA)I_{xC}/(y_C A), can't go negative, and it has yCy_C underneath.

Checkpoint
1 of 3

The water behind a vertical wall rises from 3 m deep to 6 m deep. By what factor does the horizontal water force per meter of wall grow?

Hinges come next. In Gates and Buoyancy, this one force at the center of pressure becomes a moment about a hinge.

Recap

  • On a submerged plane, F=PCA=γhCAF = P_C A = \gamma h_C A: the gauge pressure at the centroid is the average pressure.
  • It acts below the centroid, at yCP=yC+IxC/(yCA)y_{CP} = y_C + I_{xC}/(y_C A), with yy measured along the plane from the free-surface line. For a rectangle, the offset is L2/(12yC)L^2/(12y_C).
  • On a slope, hC=yCsin⁡θh_C = y_C\sin\theta, and yCy_C and yCPy_{CP} are slant distances from the surface, not from the gate's edge.
  • A wall with water to the top carries γH2/2\gamma H^2/2 per unit width, H/3H/3 above the base.
  • The deeper the surface, the smaller the offset. The force follows the centroid's depth and the area, never the volume of water behind.