Maximum Bending Moment

The moment peaks where the shear crosses zero.

Before this Lesson

Take a 20 ft simple beam under a uniform 2 kip/ft. Its largest moment sits at midspan. Now hang a point load 5 ft from the left support and slowly make it heavier. The peak starts sliding toward the load. At 40 kip it gets there, and then it stops dead. Make the load 60 kip, or 600, and the beam may object, but the peak stays put. One rule explains all of it, and the same rule finds the largest moment on every beam in this Lesson.

The shear is the slope of the hill

Walk along the moment diagram from left to right, as if it were a hill. The shear is the slope under your feet. Where VV is positive, you're climbing. Where it's negative, you're heading down. So a hilltop can only happen where the shear goes from positive to negative, and the bottom of a valley only where it goes from negative to positive. Anywhere else, the moment is still on its way somewhere.

The shear can change sign in two ways. Under a distributed load, it slides through zero, and the hilltop is round. At a point load, it leaps across zero in one jump, and the hilltop is a sharp corner. That's all the opening beam was doing.

No point load 2 kip/ft A B 5 ft 15 ft V (kip) M (kip·ft) +20 −20 +100 at 10 ft P = 24 kip 2 kip/ft A B 24 kip 5 ft 15 ft +38 +28 +4 −26 +169 at 7 ft P = 60 kip 2 kip/ft A B 60 kip 5 ft 15 ft +65 +55 −5 −35 +300 at 5 ft
The same beam as the point load grows

With no point load, the shear crosses zero at midspan. At 24 kip, the shear jumps at the load but still has +4 kip left over. The uniform load uses that up in another 2 ft, so the peak moves to 7 ft. A heavier load pushes the crossing farther left, until at 40 kip the jump lands exactly on zero. Past that, the jump carries the shear clear across: +55 kip on one side of the 60 kip load, −5 kip on the other. There's no crossing left to find, so the peak stays under the load however heavy it gets.

With no couple on the beam, that leaves four places the largest moment can be:

  • where the shear crosses zero under a distributed load;
  • under a point load, where the shear jumps through zero;
  • over an overhang's interior support, where the reaction jumps the shear through zero the other way;
  • at a fixed end, the one support that can hold a moment.

The procedure doesn't change from beam to beam:

  1. Find the reactions.
  2. Walk the shear from left to right, and locate every sign change.
  3. Find the moment at each one, from the area under the shear diagram or by cutting the beam there. Include a fixed end if there is one.
  4. Compare sizes. A negative moment counts as much as a positive one.

The cases with printed answers

The simplest beams have their answers printed, and you can see where they come from. Put a uniform load on a simple beam. Each support takes wL/2wL/2, and by symmetry the shear crosses zero at midspan. The moment there is the area of the triangle from the support to midspan, 12(L/2)(wL/2)=wL2/8\tfrac12(L/2)(wL/2) = wL^2/8. Put a point load at the center instead, and the shear is a level P/2P/2 for half the span, so that area is a rectangle, (L/2)(P/2)=PL/4(L/2)(P/2) = PL/4.

w L/2 L/2 V +wL/2 −wL/2 area = wL2/8 P L/2 L/2 V +P/2 −P/2 area = PL/4
The area up to the sign change is the peak moment

The Handbook prints these in a Maximum Moment column of its beam tables, in Mechanics of Materials. Here are the rows you'll use most.

Maximum moments from the Handbook's beam tables
Beam and loadMmaxM_{\text{max}}Where
Simple, uniform wwwL2/8wL^2/8Center
Simple, PP at centerPL/4PL/4Center
Simple, PP at aa and bb from the endsPab/LPab/LUnder the load
Simple, triangular, rising to w0w_0w0L2/(93)w_0 L^2/(9\sqrt{3})L/3L/\sqrt{3} from the zero end
Cantilever, PP at aa from the wallPaPaFixed end
Cantilever, uniform wwwL2/2wL^2/2Fixed end

Adapted from the FE Reference Handbook, Simply Supported Beam Slopes and Deflections and Cantilevered Beam Slopes and Deflections

Here ww is the intensity, in kip/ft. If a question gives the total load W=wLW = wL, divide by the length first.

The tables print no units. A load in kip/ft and a span in feet give kip⋅ft\text{kip}\cdot\text{ft}, also called foot-kips, and you multiply by 12 for kip⋅in\text{kip}\cdot\text{in}, or inch-kips. Bending Stress takes this moment as its input, usually in kip⋅in\text{kip}\cdot\text{in}, because section properties come in inches.

Checkpoint
1 of 2

A 24 ft simple beam carries a uniform load totaling 36 kip. What is its maximum moment?

kip·ft

A uniform load and an off-center point load

Now for a beam with no row: the opening beam, with an 8 kip load. The uniform load alone would peak at midspan, and the point load alone would peak under itself, so together they peak somewhere between. Use the procedure, and read the shear on both sides of the point load, because it has two values there.

Worked Example A uniform load and an off-center point load
1 of 3

Find the reactions, the zero-shear location, and the maximum moment.

2 kip/ft A B 8 kip 5 ft 15 ft
The opening beam with an 8 kip load

When the point load takes over

Go back to the opening beam at 60 kip, where Ay=65 kipA_y = 65\ \text{kip}. The shear reaches +55 at the load and jumps to −5. It has changed sign, so you've found the peak, with no crossing to look for:

Mmax=65+552(5)=300 kip⋅ftM_{\text{max}} = \frac{65 + 55}{2}(5) = 300\ \text{kip}\cdot\text{ft}

The trap is hunting for a crossing anyway. Write the shear past the load as 65−60−2x65 - 60 - 2x, set it to zero, and you get x=2.5 ftx = 2.5\ \text{ft}, which is left of the load, where that equation doesn't apply. A root outside its own segment isn't a crossing.

So at every point load, read the shear on both sides. The same sign means keep walking. Opposite signs mean a peak.

Checkpoint
0.5 kip/ft A B 30 kip 6 ft 18 ft
A uniform load and a point load

What is the maximum moment?

kip·ft

Several point loads

Take the uniform load away altogether, and the shear becomes a staircase of level steps. The moment diagram is then all straight lines, and straight lines can only peak at a corner, so the largest moment is under one of the loads. You don't need the moment under each one. Walk down the staircase and stop at the load where it crosses zero.

A B 16 kip 8 kip 14 kip 10 kip 4 ft 8 ft 4 ft V (kip) +14 −2 −10 M (kip·ft) +56 +40
Level shear, straight moment, and a peak under a load

Here the reactions are 14 kip and 10 kip, and the shear goes +14, −2, −10. It changes sign at the 16 kip load, so the peak is 14(4)=56 kip⋅ft14(4) = 56\ \text{kip}\cdot\text{ft}. If a step lands exactly on zero, as it does between two equal loads placed symmetrically, the moment is level there, and the peak runs the whole stretch.

Checkpoint
A B 15 kip 10 kip 5 kip 4 ft 6 ft 6 ft 4 ft
Three point loads on a simple beam

What is the maximum moment?

kip·ft

When the zero takes a short calculation

Two kinds of load need an extra step to locate the zero.

A partial uniform load leaves the shear level until the load begins. From there it falls by ww per unit length, so dividing the shear by ww gives a distance from the start of the load, not from the end of the beam. Take a 12 ft simple beam with 4 kip/ft from 2 ft to 8 ft, where the reactions are 14 kip and 10 kip. The shear holds at +14 for 2 ft, then reaches zero 14/4=3.5 ft14/4 = 3.5\ \text{ft} past the start of the load, at x=5.5 ftx = 5.5\ \text{ft} from AA. The area up to there is a rectangle and a triangle:

Mmax=14(2)+12(3.5)(14)=28+24.5=52.5 kip⋅ftM_{\text{max}} = 14(2) + \tfrac12(3.5)(14) = 28 + 24.5 = 52.5\ \text{kip}\cdot\text{ft}
4 kip/ft A B 14 kip 10 kip V (kip) +14 −10 28 24.5 2 ft 3.5 ft 2.5 ft 4 ft
A partial load: count the zero from the load's start

The Handbook's simple-beam table has just one partial case, a uniform load over the left half of the span: Mmax=(9/128)wL2M_{\text{max}} = (9/128)wL^2 at x=3L/8x = 3L/8.

A triangular load makes the shear curve, so there's no constant slope to divide by. Ask a different question: how far along has the load used up the reaction? Take an 18 ft simple beam with the load rising from zero at AA to 6 kip/ft at BB. The load totals 54 kip, acting at its centroid 12 ft from AA, so Ay=18 kipA_y = 18\ \text{kip} and By=36 kipB_y = 36\ \text{kip}. At a distance xx from AA, the intensity has reached x/3x/3, so the load so far is a small triangle of 12(x)(x/3)=x2/6\tfrac12(x)(x/3) = x^2/6. The shear is zero where that equals the reaction:

x26=18⇒x=10.39 ft\frac{x^2}{6} = 18 \quad\Rightarrow\quad x = 10.39\ \text{ft}

That's neither midspan nor the centroid. The load is light near AA, so the shear falls slowly at first and needs more than half the span to reach zero. In general, the zero sits L/3L/\sqrt{3}, or 0.577L0.577L, from the zero end, whichever way your beam faces. For the moment, cut there and keep the left piece. AyA_y has an arm of xx, and the 18 kip of load so far has its centroid x/3x/3 back from the cut:

Mmax=18(10.39)−18(10.393)=124.7 kip⋅ftM_{\text{max}} = 18(10.39) - 18\left(\frac{10.39}{3}\right) = 124.7\ \text{kip}\cdot\text{ft}

The Handbook's row, w0L2/(93)w_0 L^2/(9\sqrt{3}), gives the same 124.7.

6 kip/ft A B 18 kip 36 kip V (kip) +18 −36 midspan, 9 ft centroid, 12 ft V = 0 at 10.39 ft M (kip·ft) +124.7
A triangular load, and where its shear crosses zero
Checkpoint
1 of 3
5 kN/m A B 2 m 4 m 4 m
A uniform load over part of the span

What is the maximum moment?

kN·m

Overhangs have two peaks

A reaction is a point load pushing up, and at an overhang's interior support it can jump the shear from negative to positive. In hill terms, that's the bottom of a valley: a negative moment, with the overhang bending the beam down over the support. So an overhang typically has two peaks, a positive one in the span and a negative one over the support, and neither automatically wins. Find both. The negative one is the easy one, since you can cut at the support and keep the overhang, with no reactions to find.

Worked Example The largest moment on an overhang
1 of 2

Find the largest moment magnitude.

2 kip/ft A B C 12 kip 12 ft 4 ft
A loaded span with a point load on the overhang

Cantilevers peak at the wall

A cantilever under downward loads has no sign change at all. With the wall on the left, the shear stays positive all the way along, so the moment climbs from the wall to the free end, where it has to arrive at zero. The wall is the bottom of that climb, so the largest moment is there, and it's negative.

You don't even need the reactions. Cut at the wall, keep the whole beam, and add each load's moment about the wall. For a 10 ft cantilever with a 4 kip end load and 1.5 kip/ft:

∣Mmax∣=4(10)+1.5(10)(5)=40+75=115 kip⋅ft|M_{\text{max}}| = 4(10) + 1.5(10)(5) = 40 + 75 = 115\ \text{kip}\cdot\text{ft}
1.5 kip/ft 4 kip 10 ft V (kip) +19 +4 M (kip·ft) −115
The shear stays positive, and the moment bottoms out at the wall

That's two rows of the Handbook's cantilever table added together: PaPa with a=La = L, and wL2/2wL^2/2, both printed without a sign. Adding them is fair here because both peak at the same section. That's the test for adding any two cases: the same section, not just the same beam.

Checkpoint
2 kip/ft 3 kip 8 ft
A cantilever with an end load and a uniform load

What is the magnitude of the maximum moment?

kip·ft

Recap

  • The moment peaks where the shear changes sign: crossing zero under a distributed load, or jumping across zero at a point load or an interior support.
  • At a point load, read the shear on both sides. The same sign means keep walking, and opposite signs mean a peak.
  • Check both signs. An overhang's negative moment can beat the span's positive peak, and a cantilever's largest moment is at its fixed end.
  • Measure a partial load's zero from the load's start, and a triangular load's from its zero end, at L/3L/\sqrt{3}.
  • In the Handbook's beam tables, ww is the intensity. Add two cases' peaks only when they occur at the same section, and multiply kip⋅ft\text{kip}\cdot\text{ft} by 12 for kip⋅in\text{kip}\cdot\text{in}.