Shear and Moment Diagrams

The load is the slope of the shear diagram, and the shear is the slope of the moment diagram.

You can now cut a beam anywhere and find the shear and moment there. But nobody designs a beam for one section. You design it for the worst one, and the beam won't tell you where that is. You could cut it every foot and plot what you get. Do that even once and you'd notice something odd: the two plots aren't independent. One is hiding inside the other, and once you see how, you hardly need to cut at all.

Plot the cut as it slides

Take a 12 ft simple beam with 12 kip, 4 ft from AA, so Ay=8 kipA_y = 8\ \text{kip} and By=4 kipB_y = 4\ \text{kip}. Keep the left piece and slide the cut along. Anywhere in the first 4 ft, the piece holds only AyA_y, so V=+8 kipV = +8\ \text{kip} and M=8xM = 8x. Past the load, it holds the 12 kip too, so V=−4 kipV = -4\ \text{kip} and M=8x−12(x−4)M = 8x - 12(x - 4). Plot those under the beam, with xx lined up and positive values above the line, and you have the beam's shear and moment diagrams.

A B 12 kip 8 kip 4 kip 4 ft 8 ft V (kip) +8 −4 M (kip·ft) +32 slope = +8 per ft slope = −4 per ft
The 12 ft beam and its two diagrams

Compare the two plots. Over the first 4 ft, the moment climbs 8 kip·ft for every foot, and the shear is +8 kip. Over the last 8 ft, it falls 4 kip·ft for every foot, and the shear is −4 kip. The slope of the moment diagram is the height of the shear diagram. That's no coincidence.

Why the slopes match

A thin slice of beam shows why.

w V M V + dV M + dM dx
A thin slice of beam, with its faces drawn positive

The slice is dxdx long and carries a load ww per unit length. Its faces are the cut faces of a right piece and a left piece, so the positive directions are the ones you know. It has to balance, and that forces two things.

Vertically, only the load on the slice can make the two shears differ: V−w dx−(V+dV)=0V - w\,dx - (V + dV) = 0, so dV=−w dxdV = -w\,dx. As for moments, the two shears are nearly equal and opposite, which makes a couple with arm dxdx, trying to spin the slice clockwise. (The load's own moment, on so thin a slice, is too small to matter.) Only a moment that's larger on one face than the other can stop that spin, so dM=V dxdM = V\,dx. Wherever there's shear, the moment has to be changing, and the more shear, the faster it changes.

Divide by dxdx for the top row of what the Handbook prints in Mechanics of Materials, under Shearing Force and Bending Moment Sign Conventions. Add up the slices along the beam for the bottom row:

w(x)=−dV(x)dxV=dM(x)dxV2−V1=∫x1x2[−w(x)] dxM2−M1=∫x1x2V(x) dx\begin{aligned} w(x) &= -\frac{dV(x)}{dx} & V &= \frac{dM(x)}{dx} \\[4pt] V_2 - V_1 &= \int_{x_1}^{x_2} [-w(x)]\,dx & \qquad M_2 - M_1 &= \int_{x_1}^{x_2} V(x)\,dx \end{aligned}

The Handbook doesn't say which way ww points, but that minus sign only works with downward load as positive, and its beam tables draw ww downward too. It also stops there, with no shear or moment diagrams and no rules about jumps, shapes, or peaks. Those all follow from these equations.

Together they make a chain. The load sets the slope of the shear diagram, and the shear sets the slope of the moment diagram. Read the other way, each diagram is the running area of the one above it: a slice's V dxV\,dx is the area of a thin strip under the shear diagram, and stacking the strips gives the total change in moment.

And the jump at the 12 kip? A point load is a whole force landing on a slice with no width, so the shear has no room to slope, and it jumps by the size of the load. The moment can't jump there, because a force with no arm adds no moment. But its slope changes all at once, from +8 to −4, which puts a kink in the moment diagram.

When the shear slopes

Now try a beam where the shear isn't level: 12 ft, with 2 kip/ft along its whole length, so Ay=By=12 kipA_y = B_y = 12\ \text{kip}. The shear starts at +12 kip and loses 2 kip for every foot, a straight line through zero at midspan and on down to −12 kip at BB.

You can get the moment's shape from that without one cut. Its slope at every point is the shear there. So it starts out climbing steeply, at 12 kip·ft per ft, flattens as the shear shrinks, goes dead level at midspan, and then falls faster and faster. A slope that changes steadily makes a parabola, not a straight line.

2 kip/ft A B 12 kip 12 kip 6 ft 6 ft V (kip) +12 −12 V = 0 area = +36 area = −36 M (kip·ft) slope +12 slope −12 +36 slope 0
A uniform load, and the chain from load to shear to moment

Look at where the peak is. A curve stops rising exactly where its slope hits zero, so the moment peaks where the shear crosses zero. At the supports, where the shear is largest, the moment is zero and only changing fastest. The two are at their worst in different places.

The moment is a running total

Now use the Handbook's last equation, the rule you'll reach for most: the change in moment between two sections is the area under the shear diagram between them. Area above the axis raises the moment, and area below it lowers the moment. The area is the change, not the moment itself, so you add it to wherever the moment started.

On the uniform beam, a cut at 3 ft gives M=27 kip⋅ftM = 27\ \text{kip}\cdot\text{ft}, with the shear at +6 kip. The shear falls 2 kip per ft, so it reaches zero 6/2=3 ft6/2 = 3\ \text{ft} farther on, at midspan. That's a triangle of area 12(3)(6)=9 kip⋅ft\tfrac12(3)(6) = 9\ \text{kip}\cdot\text{ft}, so the moment at midspan is 27+9=36 kip⋅ft27 + 9 = 36\ \text{kip}\cdot\text{ft}. From midspan to BB, the triangle below the axis takes away 12(6)(12)=36 kip⋅ft\tfrac12(6)(12) = 36\ \text{kip}\cdot\text{ft}, which leaves zero at the roller, as it should.

If you're given loads rather than a diagram, sketch the shear between the two sections first. A uniform load lowers it by ww for each unit of length.

Checkpoint
1 of 2
V (kN) +9 −3 C D 4 m
The shear diagram between C and D

The moment at CC is +30 kN⋅m+30\ \text{kN}\cdot\text{m}. What is the moment at DD, with its sign?

kN·m

When a beam's ends carry no moment, the running total starts at zero, and then it is the moment. Pins, rollers, and free ends all qualify, as long as no couple acts anywhere along the beam. That lets you find the largest moment from a shear diagram with no beam in sight.

Between sign changes of the shear, the moment keeps moving one way, so it can only peak where the shear changes sign. Run the total to each of those points and compare sizes, since a negative moment counts as much as a positive one. A correct total comes back to zero at the far end, which is a check worth its few seconds.

Worked Example The largest moment from a shear diagram
1 of 2

This is the shear diagram of a beam with zero moment at both ends and no couples. Find the largest moment magnitude.

V (kip) +12 −6 6 ft 3 ft
A shear diagram of straight-line segments

Read the beam off its shear diagram

The chain runs backward too. Give someone a shear diagram and they can tell you every force on the beam, because each feature has just one cause.

  • A jump is a point load the size of the whole jump, wherever it starts and ends. Down is a downward load. Up is an upward force, usually a reaction.
  • A sloped segment is a distributed load, and its slope gives the intensity. A line falling 9 kN over 3 m means 3 kN/m downward.
  • A level segment means no force acts there. A couple can still sit on one, as you'll see next.
Checkpoint
1 of 2
V (kip) +12 +4 −8 4 ft 4 ft
A shear diagram with one jump

What is the size of the point load 4 ft from the left end?

kip

A couple jumps the moment

A concentrated couple is a twist applied at one point, with no net force. Slide a cut past one, just as you slid it past a point load. Just left of the couple, the left piece doesn't hold it. Just right of it, the piece does, and nothing else is new.

Just left of the couple V Just right of the couple V ML C MR = ML + C
Cuts just left and just right of a clockwise couple

There's no new force, so VV stays the same, and you'll never find a couple on a shear diagram. But the piece has a new twist to balance. The MM on a left piece's cut face is drawn counterclockwise, so when the piece picks up a clockwise couple CC, that MM has to grow by CC:

MR=ML+Cclockwise coupleMR=ML−Ccounterclockwise couple\begin{aligned} M_R &= M_L + C && \text{clockwise couple} \\ M_R &= M_L - C && \text{counterclockwise couple} \end{aligned}

So, walking left to right, a clockwise couple steps the moment diagram up, and a counterclockwise couple steps it down. The slope is the same on both sides, because the shear is. When you find reactions, a couple goes into the moment equation with no arm, the same about any point.

Worked Example A couple on a simple beam
1 of 2

Find the shear, and the moment just left and just right of the couple.

A B 36 kip·ft 8 ft 4 ft
A clockwise couple on a simple beam

Drawing both diagrams

You now have every piece. Each kind of load leaves its own mark on the two diagrams.

Load V M No load constant linear Uniform load linear parabolic Triangular load parabolic cubic Point load jump kink Clockwise couple no change jump
What each kind of load does to the shear and moment diagrams

Each step down the chain raises the power of xx by one. No load gives a constant shear and a linear moment. A uniform load gives a linear shear and a parabolic moment. A triangular load gives a parabolic shear and a cubic moment. A point load jumps the shear and kinks the moment, and a couple jumps the moment and leaves the shear alone.

To choose between sketches of a curve, use the height of the shear as the steepness of the moment. Where VV is large, MM is steep. Where VV is near zero, MM is nearly level. To draw the diagrams yourself, walk from left to right:

  1. Find the reactions.
  2. Walk the shear from zero. Jump at each point load and reaction, slope under each distributed load, and stay level everywhere else. It has to end at zero.
  3. Walk the moment from its value at the left end, which is zero for a pin, a roller, or a free end. Add each area, and step at each couple. It has to close at the far end.
Worked Example Both diagrams for a partial load and a point load
1 of 3

Draw the shear and moment diagrams.

2 kip/ft A B 8 kip 6 ft 2 ft 2 ft
A partial uniform load and a point load on a simple beam

That's the whole chain. Here's one last check on it.

Checkpoint

Which statements about shear and moment diagrams are true?

A.
The moment peaks where the shear is largest.
B.
A point load makes a jump in the shear diagram.
C.
The area under the shear diagram between two sections equals the moment at the second section.
D.
The slope of the moment diagram at a section equals the shear there.
E.
A concentrated couple jumps the moment and leaves the shear unchanged.
F.
Under a uniform load, the moment diagram is a straight line.
G.
The moment peaks where the shear crosses zero.

Recap

  • The load sets the slope of the shear diagram, w=−dV/dxw = -dV/dx, with downward load positive. The shear sets the slope of the moment diagram, V=dM/dxV = dM/dx.
  • M2−M1M_2 - M_1 is the area under the shear diagram. Area below the axis subtracts, and the area is the change, not the moment. The moment peaks where the shear changes sign, and the largest by size can be a negative one.
  • On a shear diagram, a jump is a point load, a slope is a distributed load's intensity, and a level segment means no force acts there.
  • A couple jumps the moment by its own size and leaves the shear alone. Walking left to right, clockwise steps up and counterclockwise steps down.
  • No load gives constant shear and linear moment, a uniform load gives linear and parabolic, and a triangular load gives parabolic and cubic.