Statics stops once it has the force. Mechanics of materials picks up from there and asks what that force does to the member carrying it: how hard each square inch works, and how far the member stretches, twists, or sags. Every question in this topic splits into the same two halves. In the statics half, you cut the member where it's worst off and find the internal force at the cut. In the materials half, you divide that force by the right property of the section. The materials half has only one real decision, which kind of load you're looking at, and there are just four kinds.
Statics half, materials half
Hang a 600 lb sign from a steel rod half an inch across. Cut the rod in your head, anywhere above the sign, and the piece below would drop unless the steel at the cut pulled up on it with exactly 600 lb. That pull is the internal force, and finding it was the statics half. The materials half shares it out over the rod's 0.196 in² of steel: σ=P/A, about 3,100 psi.
A floor beam under a loaded bookcase takes the same two moves, with more going on at the cut. The piece on one side needs two things to stay put: a force across the cut, the shear V, so it doesn't slide past its neighbor, and a bending moment M, so it doesn't fold. Both change along the beam, so here the statics half takes three Lessons, from Internal Shear and Moment in Beams through Maximum Bending Moment, to find where each one peaks. Then each gets its own formula.
So to name a load, picture the cut and ask what the piece needs there to stay still: a pull or push along the member, a twist about its axis, a moment that keeps it from folding, or a force across it.
Stress, strain, and the material between them
Stress is force per area, and strain is stretch per length, ε=δ/L. Dividing both ways strips out the member's size: pull a thick rod and a thin one of the same steel to the same stress, and they stretch by the same fraction of their length. So one stress-strain curve describes the material itself, and on its straight, elastic part, Hooke's law ties the two together, σ=Eε. The modulus E comes from the Handbook's material tables. Steel's is 29,000 ksi, so even 29 ksi of stress stretches it by only a thousandth of its length.
A bar that stretches also thins, by Poisson's ratio ν, and sliding has its own modulus, G. A temperature change makes strain with no load at all; block it, and the blocked strain turns into stress. And when equilibrium alone can't say how members share a load, strain supplies the missing equation, because the deformed pieces still have to fit together.
Four loads, four formulas
Each of the four internal loads spreads over a cut in its own pattern, and the pattern says where the material works hardest.
Each internal load spreads over the cut in its own pattern
An axial force spreads evenly. Torque makes shear stress that grows from zero at the center to its largest at the surface. A bending moment makes normal stress that's zero at the neutral axis and largest at the top and bottom, squeezing one face and stretching the other. Transverse shear peaks where the bending stress is zero, at the neutral axis, and vanishes at the faces.
Each pattern becomes a stress formula, and each load but shear has a deformation formula to go with it. This is the map the topic fills in, one Lesson at a time, with every formula from the Handbook's Mechanics of Materials chapter:
Each internal load, with its stress and its deformation
Internal load
Stress
Deformation
Axial force P
σ=P/A
δ=PL/AE
Torque T
τ=Tr/J
ϕ=TL/GJ
Bending moment M
σ=Mc/I
Deflection tables
Transverse shear V
τ=VQ/(Ib)
—
Source: FE Reference Handbook, Mechanics of Materials: Uniaxial Loading and Deformation, Torsion, Torsional Strain, Stresses in Beams, and the beam slope and deflection tables (adapted)
Read across, and a pattern shows. Each stress is the load divided by a property of the cut section: A, J/r, I/c, or Ib/Q. Each deformation has a modulus times a section property underneath: AE, GJ, or, inside the beam tables, EI. Torsion copies axial loading term for term. Shear gets a dash because in an ordinary beam, the sag from shear is too small to bother with, and the tables leave it out.
Stresses add, and the plane matters
Some sections carry two loads at once, and then their stresses add, as long as they act at the same point, in the same direction, on the same plane. A normal stress and a shear stress can't simply add, since they act in different directions. Combining them takes one more idea: stress belongs to a point and a plane. Cut a bar in tension straight across, and the pull shows up as pure normal stress, σ=P/A. Cut the same bar at 45°, and the same pull shows up as half that normal stress plus an equal shear.
The same pull on two different cuts
On the slanted cut, the pull splits into two equal parts, each P/2, one straight out of the face and one along it. Each spreads over a face 2 times larger, so each comes to σ/2.
Neither view is the real one; they're the same stress, seen on two planes. Turn the plane through half a turn, and its normal and shear stresses go once around a circle, Mohr's circle, which the Handbook draws under Mohr's Circle—Stress, 2D. Where the circle crosses its axis sit the principal stresses, the largest and smallest normal stresses at the point, on planes with no shear at all. That's how a normal and a shear stress at one point combine: into principal stresses on planes of their own.
Which load is it?
On the exam, a member usually comes described in words, and naming its load is the first decision.