Principal Stresses and Mohr's Circle

Rotate the element and the same stress looks different; Mohr's circle shows every view at once.

Before this Lesson

Twist a stick of chalk until it snaps. It won't break straight across, the way it does when you bend it. It breaks along a spiral that winds around the stick at about 45° to its length. That should bother you. Twisting puts only shear on a shaft's cross-sections, and chalk doesn't fail in shear. It fails in tension. So somewhere in that twisted chalk there's a tension big enough to break it, on a plane you weren't looking at.

Every plane through a point sees a different stress

You've met this once already. In Combined Stresses, a bar you only pulled had shear on its slanted cuts, with θ\theta the angle from the bar's axis to the cut's normal:

σθ=σcos⁡2θτθ=σsin⁡θcos⁡θ\sigma_\theta = \sigma\cos^2\theta \qquad \tau_\theta = \sigma\sin\theta\cos\theta

Swap in the double-angle identities, cos⁡2θ=(1+cos⁡2θ)/2\cos^2\theta = (1 + \cos 2\theta)/2 and sin⁡θcos⁡θ=(sin⁡2θ)/2\sin\theta\cos\theta = (\sin 2\theta)/2:

σθ−σ2=σ2cos⁡2θτθ=σ2sin⁡2θ\sigma_\theta - \frac{\sigma}{2} = \frac{\sigma}{2}\cos 2\theta \qquad \tau_\theta = \frac{\sigma}{2}\sin 2\theta

Plot each cut as a point, normal stress across and shear up. The point always sits σ/2\sigma/2 from (σ/2, 0)(\sigma/2,\ 0), at an angle 2θ2\theta, so every cut through the bar lands on one circle.

σ τ 2θ = 60° θ = 0° θ = 30° θ = 45° τ = σ/2 θ = 90° 0 σ/2 σ
Every slanted cut through a pulled bar lands on one circle

Read it around. The square cut, at 0°, is the right end: all of σ\sigma and no shear. The 45° cut is the top: the largest shear, σ/2\sigma/2, with σ/2\sigma/2 of normal stress still on it. The cut along the bar, at 90°, is the left end, where nothing acts.

That 2θ2\theta is the one strange thing about the picture: the circle turns twice as fast as the plane. Turn the plane 90°, and you go halfway around, so two faces at right angles always sit at opposite ends of a diameter.

Nothing here is special to a bar. The transformation equations for any element have the same form, a constant plus cos⁡2θ\cos 2\theta and sin⁡2θ\sin 2\theta terms, so every state of plane stress traces a circle: Mohr's circle, named for Otto Mohr, who put it to work in the 1880s. Only the center and radius change.

Pure shear, and the chalk

In Torsion of Circular Shafts, a little square on a twisted shaft's surface carried shear and nothing else: σx=σy=0\sigma_x = \sigma_y = 0 and τxy=τ\tau_{xy} = \tau. Its xx face has no normal stress, so it plots on the τ\tau axis, a distance τ\tau from the origin. Its yy face is 90° away on the element, so it's the other end of the diameter, the same distance on the other side. (Which one goes on top is a convention, coming up shortly.) The circle is centered on the origin, with radius τ\tau.

x y τ τ Pure shear σ τ cw τ ccw 90° x face y face +τ −τ Its circle x 45° τ tension τ compression Turned 45°
Pure shear, its circle, and the same square turned 45°

Go 90° around from either face, and you hit the σ\sigma axis at +τ+\tau and −τ-\tau: two planes with no shear at all, one in pure tension and one in pure compression. Ninety degrees on the circle is 45° on the element. Turn the square 45°, and its faces meet those stresses head-on: tension on one pair, compression on the other. They run along the original square's diagonals, which is why the squares on the rubber rod in Torsion leaned into diamonds, longer along one diagonal and shorter along the other.

Chalk is weak in tension, so it cracks square to that pull, and a crack square to a pull at 45° to the axis winds around the stick as a spiral. A ductile steel shaft is weaker in shear, so when it fails, it shears off flat across the cross-section, where the shear is largest.

Checkpoint
1 of 2

A point on the surface of a shaft under torque alone carries a shear stress of 9 ksi on the cross-section. Which statements are true?

A.
The planes at 45° to the shaft's axis carry 4.5 ksi of shear.
B.
The largest normal stress at the point is 9 ksi of tension, on a plane at 45° to the axis.
C.
The principal stresses are 9 ksi and 0.
D.
The largest shear stress at the point is 9 ksi, on the cross-section.

Plotting any element

A general element gives you two faces to plot. The xx face goes at (σx, τxy)(\sigma_x,\ \tau_{xy}) and the yy face at (σy, τxy)(\sigma_y,\ \tau_{xy}), with tension positive. Call those points X and Y. Whether each goes up or down comes from the Handbook's rule in Mohr's Circle—Stress, 2D: a shear plots above the axis when the pair on opposite faces "forms a clockwise couple," and below when it forms a counterclockwise one.

Take the Handbook's element, with τxy\tau_{xy} positive. The shears on its xx faces, up on the right and down on the left, would spin the square counterclockwise, so X plots below the axis. The shears on its yy faces would spin it clockwise, so Y plots above. Reverse the arrows, and both points swap sides. To plot a point, you never need a sign for the shear, just a look at which way each pair turns.

x y σx σx σy σy τxy τxy x faces: ccw couple y faces: cw couple σ τ cw τ ccw σy σx C 2θp R σb σa τin = R X (σx, τxy) Y (σy, τxy)
A stress element with every component positive, and its Mohr's circle
The Handbook's sketch labels the angle 2φ.

Adapted from the FE Reference Handbook, Principal Stresses and Mohr's Circle—Stress, 2D

X and Y are faces at right angles, so they're the two ends of a diameter, and the center CC sits halfway between them, on the axis:

C=σx+σy2C = \frac{\sigma_x + \sigma_y}{2}

That's the average normal stress, and since every plane lands on the same circle, every pair of perpendicular faces has the same average. The radius RR is the distance from CC out to X. Before reading on, build it from the figure.

Checkpoint

Which expression gives the radius of Mohr's circle?

A.
R=(σx−σy)2+τxy2R = \sqrt{(\sigma_x - \sigma_y)^2 + \tau_{xy}^2}
B.
R=(σx−σy2)2+τxy2R = \sqrt{\left(\dfrac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}
C.
R=(σx+σy2)2+τxy2R = \sqrt{\left(\dfrac{\sigma_x + \sigma_y}{2}\right)^2 + \tau_{xy}^2}
D.
R=σx−σy2+τxyR = \dfrac{\sigma_x - \sigma_y}{2} + \tau_{xy}

The Handbook prints both under Mohr's Circle—Stress, 2D:

C=σx+σy2R=(σx−σy2)2+τxy2C = \frac{\sigma_x + \sigma_y}{2} \qquad R = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}

The shear is squared, so its direction can't change the circle's size. It only decides which side of the axis X and Y sit on.

Principal stresses and the largest shear

The circle's two ends on the σ\sigma axis are planes with no shear. They carry the largest and smallest normal stresses of any plane on the circle, and they're the principal stresses. The Handbook writes them:

σa=C+Rσb=C−R\sigma_a = C + R \qquad \sigma_b = C - R

σa\sigma_a is the major principal stress and σb\sigma_b the minor. Minor means algebraically smallest, farthest left on the axis: 50 MPa of compression is smaller than 10 MPa of tension.

The principal planes are always there, and always at right angles. The shears on the xx faces turn one way and those on the yy faces turn the other, so as the plane turns from one to the other, its shear has to pass through zero. On the circle, that's the two places it crosses the axis, 180° apart, or 90° on the element.

The top and bottom of the circle carry the most shear, the radius: the Handbook's maximum in-plane shear is τin=R\tau_{\text{in}} = R. Those points are 90° around from the ends, so the planes of largest shear sit at 45° to the principal planes. And they aren't free of normal stress: both carry CC. (The Handbook's next line, a three-dimensional (σ1−σ3)/2(\sigma_1 - \sigma_3)/2, equals RR whenever σa\sigma_a and σb\sigma_b have opposite signs.)

Worked Example The principal stresses of an element
1 of 3

Find the principal stresses at this point, its maximum in-plane shear stress, and the normal stress on the planes that carry it.

x y 8 ksi 8 ksi 4 ksi 4 ksi 8 ksi 8 ksi
A stress element with its stresses in ksi

Which way the principal plane faces

The circle also says how far to turn. In the Handbook's circle above, the angle at CC from X to the σa\sigma_a end is 2θp2\theta_p, where θp\theta_p is the angle on the element from the xx-axis to the major principal plane, measured to the plane's normal as in Combined Stresses. The triangle from CC to X gives its tangent, the leg τxy\tau_{xy} over the leg (σx−σy)/2(\sigma_x - \sigma_y)/2:

tan⁡2θp=2τxyσx−σy\tan 2\theta_p = \frac{2\tau_{xy}}{\sigma_x - \sigma_y}

The Handbook doesn't print this, so a question that needs it usually gives it. Either way, halve the angle, because the circle turns twice as fast as the element: a circle drawn with 70° from X to σa\sigma_a means a 35° turn.

With the Handbook's plotting rule, the element turns the same way as the circle. Put τxy\tau_{xy} in as positive when it points the Handbook's way, up on the right face, and negative when it's reversed. Then a positive θp\theta_p is counterclockwise from xx, and a negative one is clockwise.

One catch: a tangent repeats every 180°, so tan⁡2θp\tan 2\theta_p has two roots on the element, 90° apart, the major and minor principal planes. Your calculator returns the one within 45° of xx. That's the major plane when σx\sigma_x is greater than σy\sigma_y, since X is then nearer the σa\sigma_a end. When σy\sigma_y is greater, it's the minor plane, and the major is 90° away. The physical check: the major principal plane always lies within 45° of the face with the larger normal stress.

Checkpoint
1 of 2

An element carries σx=12\sigma_x = 12 ksi, σy=4\sigma_y = 4 ksi, and τxy=3\tau_{xy} = 3 ksi, all positive as the Handbook draws them. Using tan⁡2θp=2τxy/(σx−σy)\tan 2\theta_p = 2\tau_{xy}/(\sigma_x - \sigma_y), how many degrees counterclockwise from the xx-axis is the major principal plane?

°

The stresses on any plane

The circle holds every plane, not just the principal ones. For the plane whose normal is θ\theta counterclockwise from xx, start at X and go 2θ2\theta counterclockwise around the circle. The point you land on is that plane. Its horizontal position is the normal stress on it, its height is the shear, and whether it's above or below the axis tells you which way that shear pair turns.

The arithmetic is one right triangle at the center. If the landing point sits at an angle ψ\psi from the σa\sigma_a end, its normal stress is C+Rcos⁡ψC + R\cos\psi and its shear is Rsin⁡ψR\sin\psi.

Worked Example Stresses on a plane at 30°
1 of 3

An element carries σx=80\sigma_x = 80 MPa, σy=20\sigma_y = 20 MPa, and τxy=40\tau_{xy} = 40 MPa, all positive as the Handbook draws them. Find the normal and shear stress on the plane whose normal is 30° counterclockwise from xx.

Reading a circle backward

Some questions hand you the circle and ask about the element. Everything runs in reverse. The circle's ends are the principal stresses. The center is halfway between them, and it's also (σx+σy)/2(\sigma_x + \sigma_y)/2, so knowing σx\sigma_x gives you σy\sigma_y. And the radius ties the rest together through its triangle, so a missing shear comes from the other two sides:

τxy=R2−(σx−σy2)2\tau_{xy} = \sqrt{R^2 - \left(\frac{\sigma_x - \sigma_y}{2}\right)^2}

For the xx face itself, use the same triangle at the center as for any plane: X sits at some angle from the σa\sigma_a end, and that angle's cosine and sine give σx\sigma_x and τxy\tau_{xy}.

Checkpoint
1 of 2
σ τ cw τ ccw 60° 0 −20 MPa 80 MPa X Y
Mohr's circle for the stress at a point

What is the normal stress on the x face?

MPa

Recap

  • As a plane turns by θ\theta, its stresses go around Mohr's circle by 2θ2\theta, so faces at right angles sit at opposite ends of a diameter.
  • Plot X at (σx, τxy)(\sigma_x,\ \tau_{xy}) and Y at (σy, τxy)(\sigma_y,\ \tau_{xy}), tension positive, with a shear above the axis when its pair turns clockwise. C=(σx+σy)/2C = (\sigma_x + \sigma_y)/2 and R=[(σx−σy)/2]2+τxy2R = \sqrt{[(\sigma_x - \sigma_y)/2]^2 + \tau_{xy}^2}.
  • σa=C+R\sigma_a = C + R and σb=C−R\sigma_b = C - R, on shear-free planes at right angles; the minor is the most negative. The maximum in-plane shear is RR, at 45° to them, on planes carrying CC.
  • Halve the angle from tan⁡2θp=2τxy/(σx−σy)\tan 2\theta_p = 2\tau_{xy}/(\sigma_x - \sigma_y) and turn the same way as the circle. If σy>σx\sigma_y > \sigma_x, add 90° to reach the major plane.
  • For a plane at θ\theta, go 2θ2\theta around from X and read the point. Uniaxial σ\sigma has σ/2\sigma/2 of shear at 45°; pure shear τ\tau has ±τ\pm\tau at 45°.