Bearings and Azimuths

Two names for the same direction, and the angle at each station turns one course into the next.

Before this Lesson

The deed to a lot says its back fence runs S 35°20′ W. The survey crew's notes say the same fence runs at 215°20′. Nobody made a mistake. And at the next corner, the crew never measured a direction at all, only an angle, yet that angle is enough to tell you which way the next fence runs.

Azimuths and bearings

Stand facing north and point straight ahead. Now sweep your arm clockwise until it lines up with the fence. The angle you swept is the fence's azimuth: a single number from 0° to 360°, always measured clockwise from north. East is 90°, south is 180°, and west is 270°.

A quadrant bearing reaches the same direction another way. Point north or south, whichever is closer to the fence, then swing toward east or west until you line up. S 35°20′ W means face south, then swing 35°20′ toward the west. The swing never passes 90°, and it never starts from east or west: S 80° W is only 10° off due west, and it's still written from the south.

N 0° S 180° E 90° W 270° S 35°20′ W Azimuth 215°20′ 35°20′
One direction, measured two ways

Deeds and plans favor bearings, which read like a sentence, and calculators favor azimuths, which have no letters. You need both, and the Handbook prints neither, so these conventions have to come with you to the exam.

Converting between them

Any conversion comes down to two questions. Where does the bearing start on the azimuth dial? North sits at 0°, or equally at 360°, and south sits at 180°. Then, does the swing run with the dial or against it? Clockwise adds, and counterclockwise subtracts.

So S 35°20′ W starts at 180° and swings clockwise: 180° + 35°20′ = 215°20′. S 35°20′ E swings the other way: 180° − 35°20′ = 144°40′. Here's every case, with β\beta for the bearing's angle:

The azimuth in each quadrant
BearingAzimuth rangeAzimuth
N β\beta E0° to 90°β\beta
S β\beta E90° to 180°180∘−β180^\circ - \beta
S β\beta W180° to 270°180∘+β180^\circ + \beta
N β\beta W270° to 360°360∘−β360^\circ - \beta

To go from an azimuth to a bearing, find its range and run the row backward. An azimuth of 300° is in the last row, so β\beta = 360° − 300° = 60°, and the bearing is N 60° W. There's no need to memorize the table. Sketch it first, and the sketch hands you the row.

Walking a line backward

Turn around on a line, and your direction flips exactly halfway around the dial. That's the back azimuth: add 180° to an azimuth under 180°, and subtract 180° from one that's 180° or more, so the answer stays between 0° and 360°.

A back bearing is easier still: keep the angle and swap both letters. N 60° E walked backward is S 60° W. The angle survives because the north-south lines at the two ends are parallel, so the line crosses both at the same slant.

N S N S A B Azimuth60° 60° Back azimuth 240° A to B: N 60° E B to A: S 60° W
The same line, walked from each end
Worked Example All the names for one line
1 of 4

A property line runs N 62°15′ W. Find its azimuth, its back azimuth, and its back bearing.

A line's quadrant sets its signs

Any line heads some amount north or south and some amount east or west. Those two pieces are its latitude, the north-south part, and its departure, the east-west part. Finding their sizes is the job of Latitudes and Departures, but you can read their signs from the direction alone. North and east are positive, and south and west are negative.

The Handbook does print this part. Its Latitudes and Departures section is a bare cross, with + Latitude at the top, − Latitude at the bottom, + Departure on the right, and − Departure on the left. Read up as north and right as east.

N + Latitude S − Latitude E + Departure W − Departure First (NE) Azimuth 0° to 90° Lat +, Dep + Second (SE) Azimuth 90° to 180° Lat −, Dep + Third (SW) Azimuth 180° to 270° Lat −, Dep − Fourth (NW) Azimuth 270° to 360° Lat +, Dep −
The four quadrants and their signs

Adapted from the FE Reference Handbook, Latitudes and Departures, with compass points, quadrants, and azimuth ranges added

A bearing hands you both signs in its letters, and an azimuth makes you find its range first. Quadrants are numbered clockwise, following the azimuth, so the second quadrant here is the southeast, not the upper left as in math class.

Checkpoint
1 of 2

A traverse course has an azimuth of 247°10′. Which describes it?

A.
Second quadrant (SE): latitude −, departure +
B.
Third quadrant (SW): latitude +, departure −
C.
Fourth quadrant (NW): latitude +, departure −
D.
Third quadrant (SW): latitude −, departure −

One move carries a direction to the next course

A traverse is a chain of straight lines, called courses, between points called stations. A closed traverse comes back to where it started, such as around a lot. An open route traverse follows a road or pipeline from one place to another.

Here's the catch: a total station has no idea where north is. It only measures the angle between two things it sights. So the crew starts with the direction of one course, measures an angle at each station after that, and carries the direction along.

Carrying is one move, the same every time. Stand at the new station and face back along the course you came in on. That direction is the back azimuth. Then turn the measured angle. An angle to the right is the plainest case: sight the last station, then turn clockwise to the next one.

1. Arrive at B on azimuth 60° N N 60° A B 2. Face back toward A: back azimuth 240° N 240° A B 3. Turn 110° to the right: azimuth 350° N 110° Azimuth 350° C A B
The one move, in three frames
Arrive on azimuth 60°, face back on 240°, and turn 110° to the right, which leaves on 350°.
Aznext=back azimuth+angle to the right\text{Az}_{\text{next}} = \text{back azimuth} + \text{angle to the right}

If the sum passes 360°, subtract 360°. Start from the back azimuth, not the azimuth you arrived on, or the new course comes out exactly 180° wrong.

Interior angles depend on which way you walk

An interior angle is the angle inside a closed traverse at a station, and whether it's an angle to the right depends on the walk. Go counterclockwise around a lot, and the inside stays on your left. Turn around at a corner to face back, and the inside is on your right, so the turn through it is a turn to the right, and it adds. Walk clockwise and that flips: the turn goes left, and it subtracts.

Walked counterclockwise Interior angle A B C D Interior angle = angle to the right Walked clockwise Interior angle A B C D Interior angle = angle to the left
The same corner, walked each way
Aznext=back azimuth±interior angle\text{Az}_{\text{next}} = \text{back azimuth} \pm \text{interior angle}

Use plus on a counterclockwise walk and minus on a clockwise one. If the difference drops below 0°, add 360°.

Deflection angles skip the turnaround

A deflection angle saves you the turnaround. Keep looking straight ahead along the course you came in on, and measure how far the next course turns off that line. A right deflection adds to the azimuth you arrived on, and a left one subtracts:

Aznext=Az+deflection rightAznext=Az−deflection left\begin{aligned} \text{Az}_{\text{next}} &= \text{Az} + \text{deflection right} \\ \text{Az}_{\text{next}} &= \text{Az} - \text{deflection left} \end{aligned}
A B C N Straight ahead, azimuth 60° Deflection left 70° Angle to the right 110° Azimuth 350°
One corner, measured two ways

It's still the same move. At that corner, 60° − 70° = −10°, and adding 360° gives the same 350°. A left deflection of 70° is an angle to the right of 180° − 70° = 110°, so the one move gives Az+180∘+180∘−70∘\text{Az} + 180^\circ + 180^\circ - 70^\circ. Those two 180s make a full circle, and only Az−70∘\text{Az} - 70^\circ is left.

Worked Example From an interior angle to a new course
1 of 4

A crew walks a closed traverse counterclockwise. Course AB has an azimuth of 96°40′, and the interior angle at B is 104°25′. Find the azimuth and the bearing of course BC.

Bearings along a route

A road or pipeline is often described by bearings, with a deflection at each turn. On a road, two straight stretches, called tangents, meet at a point of intersection, or PI, and the deflection angle between them is the intersection angle. The Handbook's Horizontal Curves section calls it II, and Horizontal Curve Geometry builds its curves on it.

Adding a deflection straight onto a bearing is where this goes wrong. Take N 72° E with a deflection of 35° to the right. Add the angles and you get N 107° E, which isn't a bearing, because no bearing passes 90°. The line has swung past due east into another quadrant.

PI N S E, due east W 72° 73° Deflection right 35° S 73° E N 72° E
A right deflection that crosses due east

Azimuths don't have this problem, since a right turn always adds and a left turn always subtracts. So convert to an azimuth, apply the deflection, and convert back. Here, 72° + 35° = 107°, which is S 73° E.

Worked Example A left deflection that crosses north
1 of 3

A road tangent runs N 18°20′ E. At the next PI, the intersection angle is 47°45′, with the road deflecting left. Find the bearing of the next tangent.

Recap

  • An azimuth is one angle swept clockwise from north. A bearing is an acute angle off north or south toward east or west. S 35°20′ W and 215°20′ are the same direction.
  • A back azimuth is 180° away and stays between 0° and 360°. A back bearing keeps the angle and swaps both letters.
  • A line's quadrant sets its signs, with north and east positive.
  • To carry a direction, face back along the back azimuth and turn the measured angle. An angle to the right adds. An interior angle adds on a counterclockwise walk and subtracts on a clockwise one.
  • A right deflection adds to the azimuth you arrived on, and a left one subtracts. To turn a bearing, convert to an azimuth, apply the deflection, and convert back. Between road tangents at a PI, the deflection is the intersection angle.