Field Triangles
You can measure the width of a river without getting wet.
Before this Lesson
- Triangle Trigonometry · Mathematics and Statistics
A tree stands on the far bank of a river, and you need to know how far away it is. Nobody's swimming over with a tape. So you stake a straight line along your own bank, measure it, and from each end you turn an angle to the tree. That's one side and two angles, which is enough: the triangle is fixed, and its third corner is over there by the tree, whether you ever visit it or not.
Every measurement is one part of a triangle
Surveyors can rarely put a tape on the distance they want. What they can reach is a line here and an angle there, and each one is a single part of a triangle. Triangle Trigonometry showed that three parts, at least one of them a side, usually fix a triangle. So most field problems come down to noticing which three parts you have, because that picks the tool.
Two angles and a side call for the law of sines. Two sides and the angle between them, or all three sides, call for the law of cosines.
Each side takes the letter of the angle it faces, so faces . The Handbook's Trigonometry section prints both laws:
Degrees, minutes, and seconds
Field angles are written the way a clock counts. A degree splits into 60 minutes, and a minute into 60 seconds, so 35°20′ means 35 degrees and 20 minutes. Twenty minutes is a third of a degree, which makes that angle 35.333°, not 35.20°. The two readings look alike and sit 8 minutes apart, and over a 400 ft sight that moves the far end about a foot.
Your calculator's trig keys want decimal degrees, so you'll convert often, and the Handbook doesn't print the conversions. To go from degrees, minutes, and seconds (DMS) to decimal, divide the minutes by 60 and the seconds by 3,600:
To go back, peel off the whole degrees and multiply what's left by 60 to get minutes. Then do the same with the leftover minutes to get seconds. For 127.4325°:
Most scientific calculators have a DMS conversion that does both directions, and it's worth finding yours. Keep the calculator in degree mode, too: should read 0.5.
Adding and subtracting work like hours and minutes, carrying or borrowing 60 at a time. To take 112°45′ from 180°, rewrite 180°00′ as 179°60′ and subtract each column, which leaves 67°15′.
Across the river: two angles and a baseline
Back to the tree. Call the ends of your baseline and , and call the tree . At each end, you turn the horizontal angle between the baseline and the tree. Horizontal angles are measured flat, so this triangle lies flat, the way it would look on a map.
You want or , and the law of sines pairs each side with the angle it faces. Here's the catch: the one side you measured, , faces the one angle nobody measured, the angle at the tree. But nobody has to go over there. The three angles add to 180°, so , and that completes the pair:
starts at , but it faces , so it goes with .
runs on a slant, so it isn't the river's width. With the baseline along the bank, the width at the tree, , is the straight line from square across to the baseline. That line makes a right triangle with as its hypotenuse and as its corner. It also makes one on the other side, with and , so you get two ways to the same number and a free check:
Two points from one setup
Two corners of a site have a pond between them, so no tape can run straight from one to the other, but there's a spot where you can see both. Set up a total station there, the surveyor's instrument that measures both angles and distances. Call that spot , measure the horizontal distance to each corner, and turn the horizontal angle between them.
That's two sides and the angle between them: the hinge from the law of cosines, with the instrument sitting at the hinge. Say you measure 420.0 ft and 310.0 ft, with 52°40′ between them:
Past 90°, the cosine turns negative and that last term adds instead of subtracting, which is just the hinge opening wider.
An angle from three measured sides
A crew with a tape can come back from a triangular parcel, or from a control figure (a measured triangle that later work hangs from), with three sides and no angles at all. Three sides fix the triangle, so the angles are already decided. The Handbook prints the law of cosines only solved for a side, so rearrange it to dig them out:
, the one with the minus sign, is the side facing the angle you want, and and are the two that meet at that corner. Mix them up and you get a perfectly good angle at the wrong corner.
When the answer has to be in DMS, keep the calculator's full value until you've converted. A thousandth of a degree is 3.6 seconds, so rounding early changes the last digits.
A corner past 90°
Take a lot with sides of 240 ft, 310 ft, and 470 ft. The largest angle always faces the longest side, so 470 goes in the slot:
The top went negative because that side is too long for a right angle to span: is more than . The minus sign is the whole message, and arccosine reads it, returning 116.85°, or 116°50′50″.
The law of sines would have lost that message. Sine is the same on both sides of 90°, so 116.85° and 63.15° share a sine of 0.892, and arcsine only ever answers 63.15°. Cosine falls steadily from 1 at 0° to −1 at 180°, so every angle in between has a cosine of its own.
A slope distance is a hypotenuse
Every triangle so far has lain flat, and its sides have been horizontal distances. The ground isn't flat, though. A tape laid on a hillside, or a total station aimed at a point uphill, measures along the slope. That slope distance is the hypotenuse of a different triangle: a right triangle standing on edge, with the horizontal distance along its bottom and the vertical distance up its side.
The vertical angle is the tilt of the line of sight, measured up or down from horizontal. The Handbook has no surveying formula for this and never mentions slope distances or vertical angles, but its Trigonometry section defines the ratios on this same triangle, with as its , as its , and as its . So:
If you're given the elevations of the line's two ends instead of an angle, their difference is , and the Pythagorean theorem finishes the job:
Use a slope distance in a map triangle as if it were horizontal, and your distances come out wrong, usually too long, so reduce first and work on the flat afterward. An angle below horizontal makes negative, which just says the far end is lower. Here, runs between the two points themselves; Differential Leveling adds the heights of the instrument and reflector.
Zenith angles: the same triangle, measured from overhead
Many total stations report a zenith angle instead of a vertical angle, measured down from straight overhead: 0° points at the sky, 90° is level, and past 90° you're looking downhill. It's the same line of sight, with its tilt measured from a different starting line, so . The Handbook doesn't mention zenith angles either.
From , the side next to the angle is a vertical one with length , and the side across from it has length . Sine and cosine follow the sides, so they swap:
If you ever doubt which is which, try a level sight, which has and and has to give . Both and equal 1, so the forms check out. The sign takes care of itself, too: past 90°, is negative, and so is .
That's every triangle in this Lesson: flat ones on the map, solved by the two laws, and right ones on edge, solved by their ratios. Before you compute anything, look at what was measured and sort it, and the sort picks the tool.