Horizontal Curve Geometry

A highway curve is an arc of a circle fitted between two straight roads.

Before this Lesson

A new highway runs straight, bends through 40°, and runs straight again. The corner of a small gas station stands 50 ft from the spot where the two center lines would cross, and the plan is to round the bend with a 1,000 ft radius. How close will the center line come to that corner? You don't need a scale drawing. One right triangle answers it, and that triangle and the arc it frames give you every other number on the curve.

40° gas station 50 ft ? center lines would cross here R = 1,000 ft Not to scale
How close does the curve come to the building?

Two tangents and the arc between them

Picture driving that bend. You can't change direction all at once, so you turn the wheel a little and hold it there, and a car with its wheel held still drives in a circle. That's why a highway curve is an arc of a circle. The arc also has to start and end running exactly along the straight road on each side, with no kink. A straight line that touches a circle that way, without crossing it, is a tangent, so the straight stretches are called tangents: the back tangent before the curve and the forward tangent after it.

Three points name the curve. The Handbook spells them out in its Horizontal Curves section, under Transportation:

  • The PC, or point of curve, is where the arc begins. The Handbook also calls it the BC.
  • The PT, or point of tangent, is where the arc ends and the forward tangent begins. The Handbook also calls it the EC.
  • The PI, or point of intersection, is where the two tangents would cross if you extended them. Nobody drives over it once the curve is built, because the road has already turned off.
angle I angle I PC PI PT O R R back tangent forward tangent directionof travel
A curve between two tangents, with the angle I in two places

Adapted from the FE Reference Handbook, Horizontal Curves

How much the road turns is the intersection angle II, also written Δ\Delta. The Handbook calls it the angle between the two tangents, and its drawing shows which angle it means: the deflection, from the back tangent extended past the PI around to the forward tangent. A road that bends through 40° has I=40∘I = 40^\circ, not the 140° you'd measure inside the corner.

The figure shows II a second time, as the arc's central angle at the circle's center, OO. The two have to match. A radius meets the road at a right angle everywhere along the arc, so picture a carpenter's square riding along the curve, with one arm on the car's heading and the other on the radius. The square is rigid. When the heading has swung through II, the radius has swung through exactly II too. That's why one angle runs through every formula in this Lesson.

How sharp is it? Radius or degree of curve

There are two ways to say how sharp a curve is. One is its radius RR. The other is the degree of curve DD, which the Handbook gives by the arc definition: the central angle covered by 100 ft of arc. Read it as a rate of turning. Drive 100 ft along a 4° curve, and your heading changes by 4°.

A rate of turning runs opposite to a radius. The sharper the curve, the bigger DD and the smaller RR.

100 ft D R Sharp curve: large D, small R 100 ft D R Flat curve: small D, large R
The same 100 ft of arc on a sharp curve and a flat one

To link the two measures, write that 100 ft of arc as the radius times the angle in radians:

100=R D π180⇒R=5729.58D100 = R\,D\,\frac{\pi}{180} \quad\Rightarrow\quad R = \frac{5729.58}{D}

That last form is the Handbook's, with DD in degrees. The 5,729.58 ft is simply the radius of a 1° curve.

Checkpoint
1 of 3

What is the radius of a 3.5° curve?

ft

One right triangle

Now draw a line from OO to the PI. The figure is a mirror image about that line, so it splits the central angle in half. Look at the triangle it makes with a radius and a tangent. The radius meets the tangent at a right angle at the PC, so this is a right triangle, with I/2I/2 at the center, RR next to that angle, and across from it the tangent distance TT from the PC to the PI. Exam questions often call it the tangent length. By symmetry, the PT sits the same distance from the PI.

PC PI PT O R T I/2 T I/2
A radius, a tangent, and the line to the PI make a right triangle
tan⁡I2=TR⇒T=Rtan⁡I2\tan\frac{I}{2} = \frac{T}{R} \quad\Rightarrow\quad T = R\tan\frac{I}{2}

That last form is the one the Handbook prints.

The long chord LCLC is the straight line from the PC to the PT. The line from OO crosses it at a right angle, at its middle, and that makes a smaller right triangle. This one has RR as its hypotenuse and half the chord opposite I/2I/2.

PC PT O R I/2 LC/2 R I/2 LC/2
Half the long chord sits across from I/2
LC2=Rsin⁡I2⇒LC=2Rsin⁡I2\frac{LC}{2} = R\sin\frac{I}{2} \quad\Rightarrow\quad LC = 2R\sin\frac{I}{2}

That's the chord from Areas of Plane Figures, with RR and II in the slots. The Handbook prints it only turned around, as R=LC/[2sin⁡(I/2)]R = LC/[2\sin(I/2)], so rearrange it when you need the chord.

The length of curve LL is the arc itself, from the PC to the PT, and no triangle is involved. The radian rule gives the first form below. The second says the same thing as turning: you need II degrees of turn at DD degrees per 100 ft. The Handbook prints both.

L=RI π180=100 IDL = RI\,\frac{\pi}{180} = \frac{100\,I}{D}

Watch where the angle goes. TT and LCLC come from half the figure, so they take I/2I/2, inside a tangent or a sine, with your calculator in degree mode. LL covers the whole arc, so it takes all of II, and that bare II is why the π/180\pi/180 is there.

Worked Example Three elements from a radius and an angle
1 of 4

A curve has R=900 ftR = 900\ \text{ft} and I=50∘I = 50^\circ. Find TT, LL, and LCLC.

Middle ordinate and external distance

Two more elements measure how far the curve bulges, and both lie on the line from OO to the PI. Walk out along that line from the center, and you pass three stops: the middle of the long chord, the middle of the arc, and the PI.

PC PI O R I/2 long chord arc M E R cos(I/2) R R / cos(I/2)
Three stops on the line from the center to the PI

The triangles already give the distance to each stop. The chord's middle is Rcos⁡(I/2)R\cos(I/2) out, the side next to I/2I/2 in the small triangle. The arc is RR out, because it's on the circle. The PI is R/cos⁡(I/2)R/\cos(I/2) out, the hypotenuse of the big triangle. The gaps between the stops are the two new elements:

M=R−Rcos⁡I2=R[1−cos⁡I2]M = R - R\cos\frac{I}{2} = R\left[1 - \cos\frac{I}{2}\right]
E=Rcos⁡(I/2)−R=R[1cos⁡(I/2)−1]E = \frac{R}{\cos(I/2)} - R = R\left[\frac{1}{\cos(I/2)} - 1\right]

The Handbook prints both final forms. The middle ordinate MM runs from the curve's midpoint inward, to the long chord. The external distance EE runs from the curve's midpoint outward, to the PI, on the outside of the curve. They're easy to swap, because they come out close in size, with EE always the larger.

angle I E M PC PI PT O T T R R I/2 I/2 L LC
Every element on one curve

Adapted from the FE Reference Handbook, Horizontal Curves

A clearance check is a subtraction along this line. If a building sits between the curve and the PI, the curve clears it by EE less the building's distance from the PI. If it sits inside the curve, between the arc and the long chord, the curve clears it by MM less the building's distance from the chord.

Worked Example Back to the gas station
1 of 3

The highway has I=40∘I = 40^\circ and R=1,000 ftR = 1{,}000\ \text{ft}. The building's corner is 50 ft from the PI, on the line to the center. How close does the center line come to the corner?

40° gas station 50 ft ? center lines would cross here R = 1,000 ft Not to scale
The building near the PI

Naming the parts

The exam sometimes points at a part of a curve and asks what it's called. Try that on a figure with nothing but letters on it.

Checkpoint
1 of 3
a b c d e f g directionof travel
A horizontal curve with its parts lettered

A car drives this curve from left to right. Which letter marks the PT?

A.
a
B.
b
C.
c

Same angle, bigger radius

Look at these four formulas together. Each one is RR times a number that depends only on II:

T=R⋅tan⁡I2L=R⋅Iπ180M=R⋅[1−cos⁡I2]E=R⋅[1cos⁡(I/2)−1]\begin{aligned} T &= R \cdot \tan\frac{I}{2} & L &= R \cdot \frac{I\pi}{180} \\[4pt] M &= R \cdot \left[1 - \cos\frac{I}{2}\right] & E &= R \cdot \left[\frac{1}{\cos(I/2)} - 1\right] \end{aligned}

So hold II fixed, and changing RR is like enlarging a photograph. The shape stays the same, and every length grows in proportion, the long chord included.

same I T 2T E 2E PI R 2R
The same tangents and angle, with the radius doubled

That may not match your instinct. A gentle curve sounds like it ought to hug the corner, yet the bigger curve starts farther back from the PI and swings farther away from it. A flatter curve cuts more of the corner, not less. That's good news for the gas station: at R=1,500 ftR = 1{,}500\ \text{ft}, EE grows to 96.3 ft, and the center line clears the corner by 46 ft instead of 14. If a question gives you DD instead, remember which way it runs against RR.

Checkpoint
1 of 2

A curve's degree of curve falls from 6° to 3°, and its intersection angle stays the same. Which of these are true?

A.
The tangent distance doubles
B.
The radius is cut in half
C.
The length of curve doubles
D.
The middle ordinate stays the same
E.
The external distance doubles

What the curve saves

The curve and the two tangents both get you from the PC to the PT. By way of the PI, that's 2T2T. Along the arc, it's LL. The difference is how much shorter the curve makes the route:

distance saved=2T−L\text{distance saved} = 2T - L

The Handbook prints TT and LL but not this difference, so subtract them yourself. For the 900 ft curve in the worked example, it's 2(419.7)−785.4=54 ft2(419.7) - 785.4 = 54\ \text{ft}.

Checkpoint

A 5° curve has an intersection angle of 48°. How much shorter is the route along the curve than the route along the two tangents through the PI?

A.
30.2 ft
B.
88.2 ft
C.
1,585 ft
D.
60.4 ft

Recap

  • A simple curve is an arc between two tangents, from the PC to the PT. The tangents would cross at the PI, and II is both the road's turn there and the arc's central angle.
  • R=5729.58/DR = 5729.58/D, where DD is the central angle of a 100-ft arc. A bigger DD is a sharper curve with a smaller radius.
  • A radius, a tangent, and the line to the PI make a right triangle with I/2I/2 at the center. It gives T=Rtan⁡(I/2)T = R\tan(I/2), a smaller triangle inside it gives LC=2Rsin⁡(I/2)LC = 2R\sin(I/2), and the arc is L=RIπ/180=100I/DL = RI\pi/180 = 100I/D.
  • M=R[1−cos⁡(I/2)]M = R[1 - \cos(I/2)] runs inward to the long chord, and E=R[1/cos⁡(I/2)−1]E = R[1/\cos(I/2) - 1] runs outward to the PI. A clearance is a subtraction along that line.
  • At a fixed II, TT, LL, MM, and EE all grow in proportion to RR. The curve saves 2T−L2T - L over the route through the PI.