Stationing Horizontal Curves

The PT is the PC plus the curve length, never the PI plus the tangent.

Before this Lesson

A road plan puts the PI of a curve at station 30+00.00. The curve has R=900 ftR = 900\ \text{ft} and I=50∘I = 50^\circ, so T=419.68 ftT = 419.68\ \text{ft} and L=785.40 ftL = 785.40\ \text{ft}. Two people on the survey crew work out where the curve ends. One adds the tangent distance to the PI and gets station 34+19.68. The other backs up to the PC, adds the curve length, and gets 33+65.72. Their stakes would land 54 ft apart. Only one matches the road, and one picture settles which.

Stations follow the road you drive

Zero a trip odometer at station 0+00 and drive the road. Every station is what the odometer reads when you get there, because stationing is distance measured along the road as built. Up to the PC, the odometer counts along the back tangent. At the PC the road leaves that straight line, so from there the odometer counts around the arc, and past the PT it counts along the forward tangent.

stations increase PC 25+80.32 PI 30+00.00 PT 33+65.72 T = 419.68 ft T = 419.68 ft L = 785.40 ft
The road as built and the route through the PI

The PI is the odd one out. Nobody drives over it, yet it has a station, because a road's tangents are laid out before its curves. The survey runs straight along the back tangent to the PI, and the PI takes its station from that line. The PC sits on the same line, one tangent distance short of the PI, so

PC=PI−T\text{PC} = \text{PI} - T

From the PC, the odometer follows the arc, which is LL long:

PT=PC+L\text{PT} = \text{PC} + L

For the curve in the hook, the PC is at 3,000.00−419.68=2,580.32 ft3{,}000.00 - 419.68 = 2{,}580.32\ \text{ft}, station 25+80.32, and the PT is at 2,580.32+785.40=3,365.72 ft2{,}580.32 + 785.40 = 3{,}365.72\ \text{ft}, station 33+65.72. The second crew member had it right.

So what did PI + T measure? Start at the PC and count TT up to the PI, then another TT down the forward tangent to the PT. That's the dashed route in the figure, 2T2T long. The road takes the arc instead, only LL long, so PI + T overshoots the PT by 2T−L2T - L. You've met that number before: it's the distance the curve saves, 54 ft here. PI + T is the PT's station on a road nobody built.

Everything past the curve inherits the arc's count. A point 300 ft down the forward tangent from the PT is at PT + 300, station 36+65.72. The Handbook's Horizontal Curves section prints TT and LL but no stationing relations, and it never explains station notation, so these come from the picture rather than from a page.

Checkpoint
1 of 3

Stations on a simple curve run along the road as built. Which of these relations are correct?

A.
PC=PI−T\text{PC} = \text{PI} - T
B.
PT=PI+T\text{PT} = \text{PI} + T
C.
PI=PT−T\text{PI} = \text{PT} - T
D.
PT=PC+L\text{PT} = \text{PC} + L
E.
PI=PC+T\text{PI} = \text{PC} + T

Working back from the PT

Sometimes the station you're handed is the PT's, say because the curve has to end where a bridge begins. Run the odometer backward. Backing up from the PT along the road takes you around the arc, so the PC is one curve length behind it. Then the back tangent carries you forward from the PC to the PI:

PC=PT−LPI=PC+T\text{PC} = \text{PT} - L \qquad \text{PI} = \text{PC} + T

The tempting shortcut is PI=PT−T\text{PI} = \text{PT} - T, as if you could back straight up the forward tangent. But the stations between the PC and the PT were counted around the arc, and the PI's station is only L−TL - T behind the PT. Subtracting TT backs you up too far, past the PI's station, and lands 2T−L2T - L before it: the same gap PI + T overshot by, now at the other end of the curve.

stations increase 2T − L 2T − L PT − T not the PI PI + T not the PT PC midpoint PC + L/2 PI PC + T PT PC + L
A curve's stations as numbers on one line
Checkpoint
1 of 2

A curve with a 1,500 ft radius and a 38° intersection angle ends at a PT at station 64+18.20. What is the station of its PI?

A.
59+39.85
B.
59+01.71
C.
54+23.36
D.
49+06.87

Running the geometry backward

A simple curve has only two numbers of its own: its size, RR or DD, and its turn, II. Every element is built from those two, so two independent facts about a curve pin it down. Find the formula that links the facts you have to the one you want, and solve it.

Stations hand you a length. The PC and PT stations differ by exactly the arc, L=PT−PCL = \text{PT} - \text{PC}, so with the radius known, L=RIπ/180L = RI\pi/180 solved for II gives the turn:

I=180 LπRI = \frac{180\,L}{\pi R}

With DD given instead, L=100I/DL = 100I/D turns around to I=LD/100I = LD/100. A tangent distance and II give the radius just as directly, from T=Rtan⁡(I/2)T = R\tan(I/2):

R=Ttan⁡(I/2)R = \frac{T}{\tan(I/2)}

The curve's midpoint is halfway around the arc, at PC + L/2, which is also the average of the PC and PT stations. It lies on the line from the center to the PI, and that makes it tempting to give it the PI's station. Don't. The PI's station is PC + T, and TT is always more than L/2L/2: the route through the PI, 2T2T, is longer than the arc, so half of it is longer than half the arc. On the number line above, the midpoint comes a little before the PI.

Worked Example A curve from its stations
1 of 3

A curve runs from a PC at station 12+40.00 to a PT at station 19+15.00, with R=1,100 ftR = 1{,}100\ \text{ft}. Find its intersection angle and the station of its midpoint.

Fitting a curve to a constraint

Real curves often start from a limit rather than a radius. A building stands in the corner of the bend. A bridge sits on the back tangent. The curve has to bulge by a set amount. Each limit fixes one element, and every element is RR times a number set by II, so a limit on an element is a limit on RR. Solve that element's formula for RR:

R=Ttan⁡(I/2)R=M1−cos⁡(I/2)R=E1/cos⁡(I/2)−1R = \frac{T}{\tan(I/2)} \qquad R = \frac{M}{1 - \cos(I/2)} \qquad R = \frac{E}{1/\cos(I/2) - 1}

The Handbook also prints the last two as (R−M)/R=cos⁡(I/2)(R - M)/R = \cos(I/2) and R/(E+R)=cos⁡(I/2)R/(E + R) = \cos(I/2), which rearrange to the same thing.

The number you get is a boundary, and before you round it you need to know which side of it is safe. Every element grows with RR, so ask which way the limit pushes the element. A building in the corner of the bend, between the road and the PI, needs the curve to swing far enough away from the PI. If the building is dd from the PI, then E≥d+clearanceE \ge d + \text{clearance}, and that makes a minimum radius.

PI d clearance E building smaller R larger R Not to scale
A bigger radius swings the curve farther from the PI

A bridge on the back tangent works the other way. The curve can't start until the bridge ends, so TT can be at most the distance from the bridge to the PI, and that makes a maximum radius.

Round toward the safe side: a minimum radius rounds up, and a maximum rounds down. Since DD runs opposite to RR, a minimum radius is a maximum degree of curve, which rounds down, and the reverse. Rounding to the nearest value can land you on the wrong side of the line.

Worked Example A radius that clears the gas station
1 of 3

A curve with I=40∘I = 40^\circ passes a gas station whose corner is 50 ft from the PI, on the line to the center, between the PI and the curve. The road needs at least 30 ft of clearance, and curves here are designed in whole degrees. What is the largest degree of curve that works?

Recap

  • Stations are distance along the road as built. Count back along the back tangent to the PC, PC=PI−T\text{PC} = \text{PI} - T, then around the arc, PT=PC+L\text{PT} = \text{PC} + L.
  • PI + T counts the route through the PI, which nobody drives, and overshoots the PT by 2T−L2T - L. Working back, PC = PT − L, then PI = PC + T. PT − T backs up too far and lands 2T−L2T - L before the PI.
  • The stations give L=PT−PCL = \text{PT} - \text{PC}, and with RR that fixes I=180L/(πR)I = 180L/(\pi R). A tangent distance and II fix R=T/tan⁡(I/2)R = T/\tan(I/2). The midpoint is at PC + L/2, a little before the PI's station.
  • A constraint fixes one element, and that element's formula solved for RR fixes the curve. "At least" is a minimum radius and "at most" a maximum. Round toward the safe side, and remember DD runs opposite to RR.