Fluid Properties
How much a fluid weighs and how much it resists flowing are the two properties most problems need.
Before this Lesson
- Newton's Second Law · Dynamics
Pour a cup of water and a cup of motor oil side by side. The water is gone in a splash, and the oil follows in a slow, lazy ribbon. It looks like the heavier stuff. Now pour the oil into the water, and it floats.
Oil is lighter than water, volume for volume, and it still flows far more reluctantly. So "heavy" and "thick" are separate questions, each with its own number. This Lesson takes them in that order.
How much a fluid weighs
Take a cubic foot of any fluid. It has a mass, and that mass has a weight. Per unit volume, the mass is its density, , and the weight is its specific weight, . Divide by the volume, and you get the line the Handbook prints in its Fluid Mechanics definitions:
Specific weight does most of the work in this topic, because every pressure in a still fluid comes from the weight of the fluid above it. Water sets the scale, so its values are worth knowing by heart.
| Property | U.S. customary | SI |
|---|---|---|
| Density | 1.94 slug/ft³ | 1,000 kg/m³ |
| Specific weight | 62.4 lbf/ft³ | 9.81 kN/m³ |
Source: FE Reference Handbook, Density, Specific Volume, Specific Weight, and Specific Gravity; Properties of Water (English Units)
The Handbook writes the SI specific weight as 9,810 N/m³, and its water table writes 1.94 in lbf-sec²/ft⁴, which is the same as slug/ft³.
Every other liquid gets measured against water. Specific gravity divides a liquid's values by water's, and :
It's a ratio, so it has no units and it's the same number in every system. An oil with has 85% of water's density and 85% of water's specific weight. Scale water's value, then multiply by a volume: and .
A pound of what?
Weight is a force, and mass is what resists acceleration, so . In U.S. units, mass gets a unit of its own, the slug: a 322 lb crate has a mass of . For more, see Newton's Second Law.
In U.S. units, "pound" does two jobs, so the Handbook's opening pages split it in two. The pound-force, lbf, is a force. The pound-mass, lbm, is a mass, set so that 1 lbm weighs 1 lbf at standard gravity. The slug is a mass too, which makes two units for one quantity:
There's no physics in that, only history. works as written with slugs, since 1 lbf accelerates 1 slug at 1 ft/sec². With lbm it needs a conversion factor, which the Handbook calls and prints as 32.174 lbm-ft/(lbf-sec²). Round it to 32.2, like :
isn't gravity, just a unit converter that happens to share its number. So a problem in lbm gives you two routes: convert to slugs and use , or keep lbm and divide by .
Let gravity be the acceleration, so . At standard gravity, and cancel, so a mass in lbm and its weight in lbf are the same number. That's why the Handbook lists water at both 62.4 lbm/ft³ and 62.4 lbf/ft³. Dividing lbm by 32.2 gives slugs, never a weight.
Four numbers for one liquid
One more property belongs on the list. Specific volume is the volume a unit of mass takes up, which is density turned upside down. The Handbook defines it only under Thermodynamics, as , so . Everywhere else in this topic, means velocity.
| Property | What it is | SI | U.S. customary |
|---|---|---|---|
| Density, | mass / volume | kg/m³ | slug/ft³ or lbm/ft³ |
| Specific weight, | weight / volume | N/m³ or kN/m³ | lbf/ft³ |
| Specific gravity, | none | none | |
| Specific volume, | volume / mass | m³/kg | ft³/lbm |
Viscosity is fluid friction
Now the second question: how hard does a fluid resist flowing? Lay a flat plate on a thin film of oil and slide it. The oil touching the plate moves with the plate, and the oil touching the table stays with the table. In between, the film shears like a deck of cards pushed from the top, with each layer sliding a little faster than the one beneath it.
Each layer rubs against its neighbors, and that rubbing is the drag you feel at the plate. The faster neighboring layers slide past each other, the harder they drag. That slide rate is the velocity gradient, : how much the speed changes per unit of distance across the flow. So shear stress follows the gradient, with viscosity as the constant in front:
That's Newton's law of viscosity. The Handbook prints it, without the name, under Stress, Pressure, and Viscosity, and calls the absolute dynamic viscosity. A fluid that obeys this law is Newtonian, as water, air, and most oils are.
A thin film makes it easy. The speed climbs in a straight line from zero to the plate's speed across a film of thickness , so the Handbook gives . Multiply the stress by the plate's wetted area for the force:
Double the speed, and each layer slides twice as fast past its neighbor. Halve the film, and the same speed difference is squeezed into half the distance. Either way the gradient doubles, and so does the stress. A bigger plate leaves the stress alone and just gives it more area to act on.
Stress over gradient sets the units of : lbf-sec/ft² or Pa·s. Films usually come in inches or millimeters, so convert to match first.
Water's table, and a second viscosity
For water, nobody runs a film test. The Handbook prints its properties by temperature in Properties of Water, one table for each system. Here are a few rows of each.
| Temp. (°F) | (lbf/ft³) | (lbf-sec²/ft⁴) | (× 10⁻⁵ lbf-sec/ft²) | (× 10⁻⁵ ft²/sec) | (psi) |
|---|---|---|---|---|---|
| 32 | 62.42 | 1.940 | 3.746 | 1.931 | 0.09 |
| 60 | 62.37 | 1.938 | 2.359 | 1.217 | 0.26 |
| 70 | 62.30 | 1.936 | 2.050 | 1.059 | 0.36 |
| 80 | 62.22 | 1.934 | 1.799 | 0.930 | 0.51 |
| 212 | 59.83 | 1.860 | 0.593 | 0.319 | 14.70 |
Source: FE Reference Handbook, Properties of Water (English Units), selected rows
| Temp. (°C) | (kN/m³) | (kg/m³) | (Pa·s) | (m²/s) | (kPa) |
|---|---|---|---|---|---|
| 0 | 9.805 | 999.8 | 0.001781 | 0.000001785 | 0.61 |
| 20 | 9.789 | 998.2 | 0.001002 | 0.000001003 | 2.34 |
| 30 | 9.764 | 995.7 | 0.000798 | 0.000000800 | 4.24 |
| 40 | 9.730 | 992.2 | 0.000653 | 0.000000658 | 7.38 |
| 100 | 9.399 | 958.4 | 0.000282 | 0.000000294 | 101.33 |
Source: FE Reference Handbook, Properties of Water (SI Metric Units), selected rows
Pick the table by the temperature's units, and read each column's heading: the English viscosities are multiples of 10⁻⁵, while the SI table prints all its zeros. Between rows, interpolate. Water at 35°C is halfway from 30 to 40, so . With no temperature stated, use the round values from earlier.
Now run your eye down the column. From freezing to boiling, water's viscosity falls to about a sixth, while its density changes about 4%. Liquids generally do this: their molecules grip each other, and heat loosens the grip, which is why cold honey barely pours. The Handbook shows this only in the numbers.
Vapor pressure, , is the pressure at which water at that temperature boils. That's why the 212°F row reads 14.70 psi, atmospheric pressure at sea level.
That leaves two columns of viscosity, which differ by the density. The Handbook defines kinematic viscosity as:
Try it on the 60°F row: . Dynamic viscosity is the drag itself, so use it for a stress or a force. Kinematic viscosity says how much that drag matters to the fluid's own inertia, since a denser fluid has more mass to keep moving. Pipe Friction takes it from this table.
Poise, stokes, and U.S. units
Viscosity comes in a pile of units, and they all convert through SI.
| Dynamic, μ | In Pa·s | Kinematic, ν | In m²/s |
|---|---|---|---|
| poise (P) | 0.1 | stokes (St) | 1 × 10⁻⁴ |
| centipoise (cP) | 0.001 | centistokes (cSt) | 1 × 10⁻⁶ |
| lbf-sec/ft² | 47.88 | ft²/sec | 0.0929 |
Source: FE Reference Handbook, Units and Conversion Factors (metric rows)
The Handbook's conversion table has no U.S. viscosity rows, so those come from its 1 lbf = 4.448 N and 1 ft = 0.3048 m: . Carried through, 1 cP = 2.09 × 10⁻⁵ lbf-sec/ft² and 1 cSt = 1.076 × 10⁻⁵ ft²/sec.
The centi- units have a nice feature. On the 20°C row, water sits at almost exactly 1 cP and 1 cSt. They come from the centimeter-gram-second system, where water's density is 1 g/cm³, so density there is just the SG. That gives a shortcut, and it shows that centipoise and centistokes match only when :
In U.S. units, comes out in ft²/sec only with in slug/ft³. Using lbm/ft³ throws it off by 32.2.
Not every fluid is Newtonian
Plot shear stress against shear rate, which is by another name. A Newtonian fluid gives a straight line through the origin, with slope . Some fluids bend away from that line. The Handbook gives them a power law, in the same section, with a consistency index and a power law index :
With , that's Newton's law again. The Handbook calls pseudoplastic and dilatant. It prints no plot, so here's what those look like.
Read the bend, not the height. The slope says how viscous the fluid acts at that shear rate. A pseudoplastic curve flattens, so the fluid thins as you shear it faster. Paint does this: it spreads easily under a brush, then stays put on the wall. A dilatant curve steepens, so the fluid thickens when sheared hard. Stir cornstarch and water gently and it's soup. Punch it and it's nearly solid.