Newton's Second Law

Draw the free-body diagram, and the unbalanced force sets the acceleration.

Before this Lesson

You step onto a bathroom scale in an elevator, and it reads 161 lb. The car starts up, and the reading jumps to 181 lb. A few seconds later the car is climbing at a steady 20 ft/s. You're moving fast, and you're moving up, so the scale must still read heavy.

It reads 161 lb, the same as when the car was parked. Then the car slows for your floor, still moving up, and the reading falls to 141 lb. Whatever the scale is responding to, it isn't your speed.

Force follows the slope, not the height

Here's that whole ride, velocity and scale on one clock.

0 5 15 20 t (s) 0 20 141 161 181 v (ft/s) scale reading (lb) speeding up steady slowing slope = 0 slope = +4 ft/s2 slope = −4 ft/s2 weight = 161 lb
One elevator ride: velocity and scale reading

While the velocity climbs, the scale reads high. While it holds steady, even at the ride's top speed, the scale reads your weight. While it falls, the scale reads low. So the reading follows the line's slope, not its height, and from Position, Velocity, and Acceleration, the slope of velocity is acceleration.

That's Newton's second law. The Handbook's Particle Kinetics section gives it for a body of constant mass as:

ΣF=ma\Sigma F = ma

Add up every force on a body. Whatever doesn't cancel is the unbalanced force, and it sets the acceleration: size ΣF/m\Sigma F/m, direction along ΣF\Sigma F. If the forces do cancel, a=0a = 0, which means constant velocity. Rest is just one constant velocity among many.

Your gut objects, because it learned physics by shoving furniture. Stop pushing a crate and it stops, so pushing seems to be what keeps it moving. But the floor was pushing back the whole time. Flick a puck across ice, where the surface barely grips, and it coasts on with nothing pushing it. Forces don't keep things moving. They change how things are moving.

Weight is a force, mass is what resists

Weight is a force, gravity's pull on a body. Mass is how hard the body is to accelerate, and it's the same on the moon or in an elevator. Let a body fall freely and its weight is the only force on it, so ΣF=ma\Sigma F = ma becomes W=mgW = mg, the Handbook's Concept of Weight entry. Turned around, that's the line you'll use most:

m=Wgm = \frac{W}{g}

In SI, force and mass have separate names, tied together in the Handbook's conversion table by 1 N = 1 kg·m/s². A 50 kg crate weighs 50(9.81)=490.5 N50(9.81) = 490.5\ \text{N}. A kilogram is never a force.

In U.S. customary problems, the pound is a force, which the Handbook writes as lbf. So "a 322 lb crate" gives its weight, and its mass takes a unit of its own: the slug, the mass that a 1 lb force accelerates at 1 ft/s², so 1 slug = 1 lb·s²/ft. The crate's mass is 322/32.2=10 slugs322/32.2 = 10\ \text{slugs}. The Handbook lists the slug in its conversion table without defining it.

Force and mass in the two systems
QuantityU.S. customarySI
ForcelbN
Massslugkg
gg32.2 ft/s²9.81 m/s²
Problems usually giveweightmass
To get the otherm=W/gm = W/gW=mgW = mg

So in U.S. units, every weight gets divided by gg before it goes into mama. Skip that, and the arithmetic runs without complaint and the acceleration comes out 32.2 times too small.

That also hands you a quick check: a/g=ΣF/Wa/g = \Sigma F/W. A net force of a quarter of the weight gives g/4g/4, and the whole weight gives gg, which is free fall.

The Handbook's opening pages also write the law as F=ma/gcF = ma/g_c, with mass in lbm. That's the same law with different bookkeeping, and it can wait for Fluid Properties.

Four moves on a level floor

Every problem in this Lesson runs on the same four moves.

  1. Draw the free-body diagram. Isolate the body, then draw its weight and every force touching it. Put the acceleration beside the body as a separate arrow, because mama isn't a force.
  2. Set one axis along the acceleration, positive in its direction.
  3. Across the motion, the forces balance, since nothing accelerates that way. That gives the normal force.
  4. Along the motion, write ΣF=ma\Sigma F = ma.

The Handbook prints no incline, elevator, or pulley problem, only ΣF=ma\Sigma F = ma, W=mgW = mg, and the friction law. The diagram does the rest.

Start with a crate shoved across a rough floor. In Static Friction, friction took only what it needed, up to μsN\mu_s N. Once the crate is sliding, it's a fixed amount set by how hard the surfaces are pressed together, and it points against the sliding. The Handbook's Dynamics chapter, under Friction, writes:

F=μkNwhen slip is occurringF = \mu_k N \quad \text{when slip is occurring}

A problem gives you the coefficient of kinetic friction, μk\mu_k. The same section notes that starting a slip takes more force than keeping it going, so μk\mu_k normally comes in below μs\mu_s.

P W N F = μk N a
A crate pushed across a rough floor

Across the motion, N=WN = W. Along it, P−μkW=(W/g)aP - \mu_k W = (W/g)a. A constant force makes a constant acceleration, so once you have aa, the rest belongs to Constant-Acceleration Motion.

Worked Example A crate across a rough floor
1 of 3

A 200 lb crate on a level floor is pushed by a constant 80 lb horizontal force, with μk=0.25\mu_k = 0.25. Starting from rest, how long does it take to reach 10 ft/s, and how far does it travel?

The normal force is whatever the surface must supply

On that floor, NN came out equal to WW. That was a result of the setup, not a rule. A floor has no particular number in mind. It pushes back just hard enough that the crate neither sinks in nor lifts off, so anything else pushing up or down changes the answer.

Pull with a rope angled up at α\alpha, and call its tension TT. The horizontal part, Tcos⁡αT\cos\alpha, drives the crate. The vertical part, Tsin⁡αT\sin\alpha, carries some of the weight, so the floor supplies less, and friction drops with it. You met this at impending slip in Static Friction. The only change is that the horizontal equation now equals mama and not zero.

N=W−Tsin⁡αTcos⁡α−μkN=WgaN = W - T\sin\alpha \qquad\qquad T\cos\alpha - \mu_k N = \frac{W}{g}a
α T T cos α T sin α W N μk N a N = W − T sin α
A rope at an angle takes some of the load off the floor
Worked Example A crate on an angled rope
1 of 2

A rope 30° above the horizontal pulls a 150 lb crate across a rough level floor with a tension of 60 lb, and μk=0.20\mu_k = 0.20. Find the crate's acceleration.

Tilt the floor

On an incline the acceleration runs along the slope, so the axis does too. That leaves the weight as the one force not lined up with anything, so split it, as you did in Static Friction: Wsin⁡θW\sin\theta along the slope and Wcos⁡θW\cos\theta into it. Across the motion, N=Wcos⁡θN = W\cos\theta. For a block sliding down, the weight's component drives and friction resists:

Wsin⁡θ−μkWcos⁡θ=WgaW\sin\theta - \mu_k W\cos\theta = \frac{W}{g}a
θ θ W sin θ W cos θ W N μk N a
A block sliding down a rough incline

Every term has a WW, so it cancels: a=g(sin⁡θ−μkcos⁡θ)a = g(\sin\theta - \mu_k\cos\theta). A light block and a heavy block of the same material slide down together.

Now pull the block up the slope with a force PP parallel to it. Friction opposes the sliding, so it flips to point down the slope, right alongside the weight's component. Both resist the pull, and the axis now runs up the slope:

P−Wsin⁡θ−μkWcos⁡θ=WgaP - W\sin\theta - \mu_k W\cos\theta = \frac{W}{g}a
Worked Example A block sliding down
1 of 3

A 50 lb block slides down a 30° incline with μk=0.20\mu_k = 0.20. Find its acceleration.

In an elevator, only the acceleration matters

A car on a cable has no surface and no friction, just two forces in a line: the cable's tension TT up and the weight WW down. Set the axis along the acceleration, as always:

a upward:  T−W=Wgaa downward:  W−T=Wgaa\ \text{upward:}\ \ T - W = \frac{W}{g}a \qquad\qquad a\ \text{downward:}\ \ W - T = \frac{W}{g}a

Notice what's missing: any mention of which way the car is moving. A car speeding up on the way up and a car slowing down on the way to the lobby both accelerate upward, and their cables can't tell them apart.

A scale reads the force it pushes up on your feet: the normal force, not your weight. To find it, isolate the passenger alone: N−Wp=(Wp/g)aN - W_p = (W_p/g)a for an upward acceleration. The 161 lb rider from the start has a mass of 5 slugs, so at 4 ft/s24\ \text{ft/s}^2 upward the scale reads 161+5(4)=181 lb161 + 5(4) = 181\ \text{lb}. Cut the cable and a=ga = g downward, so N=0N = 0. Your weight hasn't gone anywhere. The scale is just falling too.

So the cable holds up the car and everything in it, while the scale holds up only the passenger.

car + passenger T Wc + Wp a passenger alone Wp N from the scale a
Two free-body diagrams from the same elevator
Worked Example A cable and a scale
1 of 3

A 3,000 lb elevator car carries a 180 lb passenger standing on a scale. The car speeds up going upward at 5 ft/s25\ \text{ft/s}^2. Find the cable tension and the scale reading.

Two bodies, one cord

Tie a block on a table to a hanging weight, with a cord over a pulley at the edge. Equilibrium of a Particle settled the ideal pulley: it only turns the cord, so one cord carries one tension. And a cord that doesn't stretch gives both bodies the same size of acceleration.

So draw two diagrams, each with its own positive direction, the way that body accelerates: toward the pulley for block A, and downward for block B.

A μk B A WA N T μk N a B T WB a
A block on a table and a hanging block, each drawn free
T−μkWA=WAgaWB−T=WBgaT - \mu_k W_A = \frac{W_A}{g}a \qquad\qquad W_B - T = \frac{W_B}{g}a

Add them and TT cancels:

a=WB−μkWA(WA+WB)/ga = \frac{W_B - \mu_k W_A}{(W_A + W_B)/g}

Read that as a sentence: the force driving the system, minus the force resisting it, over the mass of everything that moves. That sentence fits any version of this setup. Then get TT from whichever body's equation looks easier.

The tension is not the hanging weight. If the cord pulled up on B with all of WBW_B, B would feel no net force and wouldn't accelerate.

On an incline, settle the direction first, because friction needs to know it. Compare the hanging weight with WAsin⁡θW_A\sin\theta. The larger one wins, and friction opposes that motion. If static friction can cover the difference, nothing moves at all.

Worked Example A block on a table, pulled by a hanging block
1 of 3

A 20 lb block A on a level table, with μk=0.25\mu_k = 0.25, is tied by a cord over an ideal pulley to a hanging 12 lb block B. The blocks are moving. Find the acceleration and the cord tension.

When friction does the pushing

Put a crate on a flatbed truck and pull away from a light. What makes the crate speed up? The bed is all that touches it, so it has to be friction, pointing forward, the way the crate is moving. That's no contradiction. Friction opposes sliding between the two surfaces, and if you erase friction in your head, the truck leaves and the crate slides backward along the bed.

The crate isn't sliding, so this is static friction, and it takes only what it needs: (W/g)a(W/g)a. The harder the truck accelerates, the more it needs, up to the ceiling of μsN\mu_s N, with N=WN = W:

Wgamax⁡=μsW⇒amax⁡=μsg\frac{W}{g}a_{\max} = \mu_s W \quad\Rightarrow\quad a_{\max} = \mu_s g

The weight cancels again. Under braking, friction flips to point backward, with the same ceiling. Past it, the crate slides and friction drops to μkN\mu_k N. A level conveyor works the same way. And the truck itself is the same story one level up: friction from the road is the unbalanced force, and that's where the decelerations in Constant-Acceleration Motion come from.

speeding up v a W N F braking v a W N F F ≤ μs N
The same crate as the truck speeds up and as it brakes
Worked Example Braking with a crate on the bed
1 of 3

A 500 lb crate rides on a level truck bed, with μs=0.40\mu_s = 0.40, and the truck is traveling at 45 mph. Find the greatest deceleration that doesn't make the crate slide, and the shortest stopping distance at that deceleration.

Judging without calculating

Some questions skip the numbers and ask for the reasoning itself. One test helps with any diagram: every force on it needs a source, either gravity or something touching the body.

Checkpoint
1 of 3

An elevator car of weight WW hangs from a cable with tension TT. Which statements are true?

A.
Speeding up while moving upward, T>WT > W.
B.
Moving upward at constant speed, T>WT > W.
C.
Moving downward at constant speed, T=WT = W.
D.
Slowing down while moving upward, T>WT > W.
E.
Speeding up while moving downward, T<WT < W.

Recap

  • ΣF=ma\Sigma F = ma: the unbalanced force sets the acceleration. Balanced forces mean constant velocity, not rest.
  • Weight is a force and mass resists acceleration, so m=W/gm = W/g. In U.S. units, divide every weight by gg, which gives slugs.
  • Set one axis along the acceleration. The forces across it give NN: Wcos⁡θW\cos\theta on an incline and W−Tsin⁡αW - T\sin\alpha under an angled rope. Sliding friction is μkN\mu_k N, against the sliding.
  • On a cable, only the direction of the acceleration matters, and a scale reads the normal force. Over one pulley, aa is the driving force minus the resisting force, over the total mass, and TT isn't the hanging weight.
  • On a level bed, static friction caps the acceleration at μsg\mu_s g, speeding up or braking.