Continuity and Bernoulli's Equation

Where a pipe narrows, the water speeds up, and its pressure drops to pay for it.

Before this Lesson

Two pressure gauges sit on a level water main. One is on a 12 in. pipe, where the water moves at 4 ft/s, and it reads 40 psi. The other is just past a reducer, on a 6 in. pipe. Squeezing the water into the smaller pipe ought to push its pressure up, surely?

It reads lower, and the water there moves four times as fast. Two rules explain both: one counts the water, and the other counts its energy.

What goes in comes out

Start by counting the water. In steady flow, nothing at any point in the pipe changes from moment to moment. Water barely compresses, and a full pipe has no room to store more, so every cubic foot that enters one end pushes a cubic foot out the other. Whatever passes one section each second passes every section.

That amount is the flow rate, QQ, in ft³/s (cfs), m³/s, or L/s, with 1,000 L to the cubic meter. In a short time Δt\Delta t, the water crossing a section fills a slug of pipe v Δtv\,\Delta t long, so its volume is Av ΔtAv\,\Delta t, and the flow rate is the Handbook's continuity equation:

Q=AvQ = Av

Here vv is the average velocity across the section. Real water moves fastest at the center and slowest at the wall, and vv is the one speed that would carry the same flow.

1 A1 2 A2 flow v1 Δt v2 Δt
The same volume crosses each section in the same time

Two sections on one pipe carry the same flow:

A1v1=A2v2⇒v2=v1A1A2=v1(D1D2)2A_1 v_1 = A_2 v_2 \quad\Rightarrow\quad v_2 = v_1\frac{A_1}{A_2} = v_1\left(\frac{D_1}{D_2}\right)^2

Section 1 is upstream and section 2 downstream, here and through the rest of the topic. Halving the diameter quarters the area, so the Hook's water goes from 4 ft/s to 16 ft/s. The narrow pipe isn't squeezing the water. It gives the same flow less room.

At a junction, the flows add: Q1=Q2+Q3Q_1 = Q_2 + Q_3. The Handbook states this for parallel pipes, under Multipath Pipeline Problems. The branch areas don't decide the split, so a problem has to give you one branch's flow or velocity.

For the mass flowing each second, multiply by the density, as the Handbook's continuity equation does: m˙=ρQ=ρAv\dot m = \rho Q = \rho A v, in kg/s or slug/s. Using γ\gamma instead gives a weight per second, a different quantity.

Checkpoint
1 of 3

Water flows at 3.6 ft/s in a 10 in. pipe, which reduces to 6 in. What is the velocity in the 6 in. pipe?

ft/s

Work and energy, one pound of water at a time

Continuity says how fast the water moves. For its pressure, count its energy, with the principle from Work and Energy.

Follow the water between sections 1 and 2 for a short time Δt\Delta t. A slug of volume Q ΔtQ\,\Delta t crosses section 1, and an equal slug crosses section 2. The flow is steady, so the water in between ends as it began. The net effect is one slug, of weight W=γQ ΔtW = \gamma Q\,\Delta t, carried from section 1 to section 2.

datum z1 z2 1 2 v1 Δt v2 Δt flow P1A1 P2A2
The pushes that do work on the water between two sections

The water behind pushes forward at section 1 with P1A1P_1A_1 through a distance v1Δtv_1\Delta t, doing work P1A1v1Δt=P1Q ΔtP_1A_1v_1\Delta t = P_1Q\,\Delta t. The water ahead pushes back at section 2 with P2A2P_2A_2 through v2Δtv_2\Delta t, doing −P2Q Δt-P_2Q\,\Delta t. The walls don't move, so they do no work, and gravity is in the potential energy. With no friction, that's everything:

12Wgv22+Wz2=12Wgv12+Wz1+(P1−P2) Q Δt\tfrac12\frac{W}{g}v_2^2 + Wz_2 = \tfrac12\frac{W}{g}v_1^2 + Wz_1 + (P_1 - P_2)\,Q\,\Delta t

Divide by the slug's weight, γQ Δt\gamma Q\,\Delta t, and the weight and Δt\Delta t cancel, leaving the Handbook's Bernoulli equation:

P1γ+v122g+z1=P2γ+v222g+z2\frac{P_1}{\gamma} + \frac{v_1^2}{2g} + z_1 = \frac{P_2}{\gamma} + \frac{v_2^2}{2g} + z_2

Every term is an energy per unit weight, ft-lb per lb or N·m per N. The pressure terms are the work the surrounding water does pushing the flow along, and they're what makes this more than a falling-body problem.

Each step of the derivation leaned on an assumption:

  • Steady flow. Nothing at a point changes with time, so the water between the sections ends as it began.
  • Incompressible fluid. γ\gamma stays fixed, so the two slugs have equal volumes. That's true of liquids, and of a gas only at low speed.
  • No friction. No energy turns into heat. The Energy Equation adds the head loss real pipes have.
  • No pump or turbine between the sections. Nothing else does work on the water.
  • Along a streamline. The water followed one path from section 1 to section 2. In a pipe, one average velocity per section stands in for that path.

The Handbook's Bernoulli Equation section names friction and pumps outright, and its energy equation adds steady and incompressible.

Every term is a height

An energy per unit weight comes out as a length, so each term is a height of the flowing water, called a head. In the words of the Handbook's Energy Line section, the sum of the pressure, velocity, and elevation heads is constant.

  • Pressure head, P/γP/\gamma, is the column of water the pressure would hold up, as in Pressure and Depth. A standpipe tapped into the pipe fills to P/γP/\gamma above the centerline.
  • Velocity head, v2/2gv^2/2g, is the height the water would fall from rest to reach vv, v=2ghv = \sqrt{2gh} run backward. At 10 ft/s, it's 102/2(32.2)=1.5510^2/2(32.2) = 1.55 ft.
  • Elevation head, zz, is the centerline's height above a datum. Any datum works if both sections share it.

Their sum is the total head, HH, the same at both sections.

Every term must be a length before you add, so divide a pressure by γ\gamma first: lbf/ft² (psi times 144) over 62.4 lbf/ft³, or kPa over 9.81 kN/m³. One psi is 2.31 ft of water. Use gauge pressure at both sections. Absolute works too, since the atmosphere's head cancels, but mixing the two doesn't.

Checkpoint
1 of 2

Between which pairs of points can you write Bernoulli's equation as it stands, with nothing added?

A.
The inlet and outlet of a short, smooth reducer in a level water line
B.
The inlet and outlet flanges of a pump
C.
Two points 2 miles apart on a water main, where friction matters
D.
The two ends of a short riser that widens gradually from 6 in. to 12 in. as it climbs
E.
Two points in a pipe just as a valve downstream is slammed shut
F.
Two points in a gas line where the gas's density changes a lot between them

Faster water, lower pressure

With the total fixed, one head can grow only if another shrinks. In a level pipe, zz can't change, so where the water speeds up, its pressure has to fall. That's the Hook's lower reading.

Newton's second law agrees. A parcel of water on the centerline speeds up from 4 to 16 ft/s entering the narrow pipe, so something pushes it forward. No wall touches it, and gravity acts square to its path, so the push has to come from the water around it: more pressure behind than ahead. Water speeds up only by moving toward lower pressure, and where it slows again, the pressure climbs back.

total head H = 30 ft flow datum 4 ft 25 ft 1 ft 1 4 ft 10 ft 16 ft 2 14 ft 15 ft 1 ft 3 elevation head, z pressure head, P/γ velocity head, v²/2g
The three heads at three sections of a frictionless pipeline

In the figure, the total head is 30 ft. The throat at section 2 has half the diameter, so the water moves four times as fast, and the velocity head, which goes as v2v^2, is 16 times as large: 16 ft instead of 1. The pressure head pays those 15 ft, dropping from 25 ft to 10 ft.

Past the throat, the pipe widens back and climbs 10 ft to section 3. It's back to section 1's diameter, so continuity holds the velocity head at 1 ft, and the climb comes out of the pressure head, 25 ft down to 15 ft. Unlike a ball thrown upward, water in a full pipe of one diameter can't slow down as it climbs.

So, to judge the heads by inspection, let continuity set the velocity head. The pressure head takes whatever is left of the fixed total.

Checkpoint
1 of 2

Water flows through a level pipe that widens from 4 in. to 8 in. Ignoring friction, how do the velocity and pressure in the 8 in. pipe compare with those in the 4 in. pipe?

A.
Lower velocity and lower pressure
B.
The same velocity and higher pressure
C.
Lower velocity and higher pressure
D.
Lower velocity and the same pressure, since the pipe is level

Through a reducer or expansion

The typical exam problem puts both rules to work: water flows through a reducer or expansion, maybe climbing or dropping, with the upstream pressure given and the downstream one asked. Pick two points, section 1 upstream and section 2 downstream. Find each velocity head by continuity, turn the known pressure into a head, and solve Bernoulli for the other:

P2γ=P1γ+v12−v222g+(z1−z2)\frac{P_2}{\gamma} = \frac{P_1}{\gamma} + \frac{v_1^2 - v_2^2}{2g} + (z_1 - z_2)

Read it as a ledger: the downstream pressure head is the upstream one, plus what the water gives up by slowing down, plus what it gives up by dropping. Speeding up or climbing makes those terms negative.

Worked Example The Hook's second gauge
1 of 3

A level water main reduces from 12 in. to 6 in. In the 12 in. pipe, the water moves at 4 ft/s, and the gauge reads 40 psi. Find the pressure in the 6 in. pipe, ignoring friction.

Recap

  • Water in a full pipe can't pile up: Q=AvQ = Av with vv the average velocity, so A1v1=A2v2A_1v_1 = A_2v_2 and vv goes as 1/D21/D^2. Flows add at a junction, and m˙=ρQ\dot m = \rho Q.
  • Bernoulli's equation is work-energy per unit weight of water: P1/γ+v12/2g+z1=P2/γ+v22/2g+z2P_1/\gamma + v_1^2/2g + z_1 = P_2/\gamma + v_2^2/2g + z_2, for steady, incompressible flow along a streamline, with no friction and no pump or turbine between the sections.
  • Each term is a head, a height of water: a standpipe's rise, the fall that would give the speed, and the height above a datum. Turn pressures into heads before adding, gauge on both sides.
  • With the total fixed, faster water has lower pressure, and a climbing pipe of one diameter keeps its velocity and loses pressure head.