Lateral Earth Pressure

How hard soil pushes on a wall depends on whether the wall moves away, stays put, or pushes back.

Two concrete walls each hold back 10 ft of the same dry sand. One is a basement wall, braced at the top by the first-floor slab and at the bottom by the basement floor. The other is a retaining wall beside a driveway, with nothing at its top. The basement wall gets designed for half again as much push from the sand.

The sand is identical. The difference is that the retaining wall is allowed to lean away from it by a fraction of an inch, and that barely visible movement cuts the sand's push by about a third. This Lesson works out why, and how big each push is.

Sideways is a fraction of down

Fill a tank with water, and at any depth the water pushes on the walls exactly as hard as it presses down. A fluid can't resist shear, so squeeze it one way and it presses out every other way equally. Now fill the tank with dry sand. The grains lean on one another, and friction at their contacts lets the pile carry part of its weight straight down through the grain skeleton. The walls feel only a fraction of the vertical stress, and that fraction is the coefficient of lateral earth pressure KK:

σh′=Kσv′\sigma'_h = K\sigma'_v

The primes matter. Friction belongs to the grains, so KK multiplies the vertical effective stress from Effective Stress. In this Lesson the backfill is dry, so u=0u = 0 and σv′=γz\sigma'_v = \gamma z at a depth zz below its surface. Water in the backfill waits for Earth Pressure with Water and Surcharge.

Which fraction? That depends on what the wall does, and the simplest case is a wall that doesn't move at all. The soil behind it is then held sideways just as it was in the ground before anyone dug, neither squeezed nor allowed to spread. That's the at-rest state. The Handbook's Horizontal Stress Profiles and Forces gives its coefficient for a normally consolidated soil:

K0≈1−sin⁡ϕK_0 \approx 1 - \sin\phi

It's a rule fitted to measurements, not a derivation, hence the ≈\approx. The Handbook prints a second form for overconsolidated soil, which this Lesson leaves aside. For a sand with ϕ=30∘\phi = 30^\circ, K0=0.5K_0 = 0.5: at rest, the sand pushes sideways half as hard as it presses down.

The pressure triangle

Since σv′=γz\sigma'_v = \gamma z, the pressure on the wall is σh′=Kγz\sigma'_h = K\gamma z. It's zero at the top and grows in a straight line to KγHK\gamma H at the base of a wall of height HH, so plotted against the wall it makes a triangle.

Kγz Wall KγH H z P = ½KγH2 H/3 Backfill
Lateral pressure on a wall grows linearly with depth
The resultant is the triangle's area, and it acts through the triangle's centroid.

The total push on one foot (or one meter) of wall, measured along its length, is the triangle's area, half its base times its height:

P=12KγH2P = \tfrac{1}{2}K\gamma H^2

That's a force per unit length of wall, in lb/ft or kN/m. It acts through the triangle's centroid, H/3H/3 above the base: the push sits low, where the pressure is largest. Its overturning moment about the base is the force times that arm, P(H/3)P(H/3).

Checkpoint
1 of 2

A basement wall braced by floor slabs at the top and bottom holds back 9 ft of dry sand with γ=118\gamma = 118 lb/ft³ and ϕ=34∘\phi = 34^\circ. What is the lateral pressure at the base of the wall?

psf

Let the wall move

Now let the wall lean away from the backfill. The sand behind it follows, and to follow, a wedge of it has to slide down along a plane that runs up from the base of the wall. Sliding calls up friction along that plane, pointing up the slope, and the friction holds up part of the wedge's weight. Whatever the friction carries, the wall doesn't, so the push drops. It bottoms out when the friction is fully used and the soil fails: the active state, with coefficient KAK_A.

Push the wall into the backfill instead, and the wedge has to be shoved up and out. Friction now points down the plane, against the motion, so the wall must lift the wedge and beat the friction too. The push climbs until the soil fails the other way: the passive state, KPK_P, many times the at-rest push. The passive wedge is also longer and flatter, so there's more soil to shove.

At rest No movement K0 45° + φ/2 Friction Wedge slides down Wall moves away Active KA 45° − φ/2 Friction Wedge shoved up Wall pushed in Passive KP
The three states, and the wall movement behind each
Movement is exaggerated. Drawn for ϕ=30∘\phi = 30^\circ: the active slip plane rises at 45∘+ϕ/2=60∘45^\circ + \phi/2 = 60^\circ, and the passive one at only 45∘−ϕ/2=30∘45^\circ - \phi/2 = 30^\circ.

The two limits need very different amounts of movement. Typical figures for sand, measured at the top of the wall, are about 0.1 to 0.4 percent of its height to reach active and about 1 to 4 percent to reach full passive, roughly ten times as much; for a medium-dense sand, call it 0.2 percent and 2 percent. The passive push has much farther to climb: from half of σv′\sigma'_v to several times it, where the active push only has to ease from a half to about a third. For a 10 ft wall in medium-dense sand, that's about a quarter inch to reach active and about 2.4 in for full passive. The Handbook doesn't give these figures.

KA KP Earth pressure coefficient, K 0 0.02H 0.002H K0 Active Passive Away from backfill Into backfill
How the earth pressure coefficient changes as the wall moves
Typical values for a medium-dense sand. Not to scale vertically.

That settles the two walls from the start. The retaining wall can lean a quarter inch without anyone noticing, so it's designed for KAK_A. The basement wall, pinned by its floor slabs, can't, so it gets K0K_0. A wall is designed for the state its movement allows.

Both limits are the failure circle

Active and passive are both failure, so they come straight from the circle in Triaxial Tests and Failure Planes. At a depth zz, the soil above fixes σv′=γz\sigma'_v = \gamma z, and moving the wall changes only σh′\sigma'_h. At rest, the circle between K0σv′K_0\sigma'_v and σv′\sigma'_v sits safely under the envelope.

Let the wall move away, and σh′\sigma'_h falls while σv′\sigma'_v stays put. The circle's left end slides left and the circle grows until it touches the envelope. That's a triaxial test with σv′\sigma'_v as σ1\sigma_1 and σh′\sigma'_h as σ3\sigma_3, so σh′/σv′\sigma'_h/\sigma'_v is the failure ratio upside down. Push the wall in, and σh′\sigma'_h climbs past σv′\sigma'_v. Now σv′\sigma'_v is the smaller stress, σ3\sigma_3, and the circle grows to the right until it touches. The Handbook's Horizontal Stress Profiles and Forces prints both results:

KA=tan⁡2 ⁣(45∘−ϕ2)KP=tan⁡2 ⁣(45∘+ϕ2)K_A = \tan^2\!\left(45^\circ - \frac{\phi}{2}\right) \qquad K_P = \tan^2\!\left(45^\circ + \frac{\phi}{2}\right)
Shear stress, τ Effective normal stress, σ′ τF = σ′ tan φ φ KAσ′v K0σ′v σ′v KPσ′v Passive At rest Active
At a fixed vertical stress, only the horizontal stress moves
Drawn for ϕ=30∘\phi = 30^\circ. The active circle shrinks σh′\sigma'_h to σv′/3\sigma'_v/3; the passive circle raises it to 3σv′3\sigma'_v.

Each coefficient there carries the fine print "smooth wall, c=0c = 0, level backfill": a vertical wall with no friction against the soil, a cohesionless backfill, and a level surface. That's the case this Lesson covers. The two are reciprocals, KP=1/KAK_P = 1/K_A, which makes a quick check. For ϕ=30∘\phi = 30^\circ, KA=1/3K_A = 1/3 and KP=3K_P = 3, nine times as large, with K0=0.5K_0 = 0.5 between them.

Earth pressure coefficients from the Handbook's formulas
ϕ\phiKAK_AK0K_0KPK_P
25°0.4060.5772.46
30°0.3330.5003.00
35°0.2710.4263.69
40°0.2170.3574.60
Checkpoint
1 of 3

Three structures sit in the same dry sand:

  1. the side walls of a buried concrete box culvert, held apart by its top and bottom slabs;
  2. a cantilever retaining wall along a highway cut, with nothing at its top;
  3. a buried anchor block that a tie rod pulls toward the sheet-pile wall it anchors, judged on the face toward the wall.

Which pressure state should each be designed for?

A.
1 active, 2 active, 3 passive
B.
1 at rest, 2 at rest, 3 passive
C.
1 at rest, 2 active, 3 passive
D.
1 at rest, 2 active, 3 active

The active push on a wall

A wall free to lean is designed for the active state, so KAK_A goes into the triangle. The pressure at depth zz is KAγzK_A\gamma z, the resultant is PA=12KAγH2P_A = \tfrac{1}{2}K_A\gamma H^2 per unit length, and it acts H/3H/3 above the base. The Handbook's figure under Horizontal Stress Profiles and Forces prints this force for the top layer of a two-layer backfill, PA1=12γ1KAH12P_{A1} = \tfrac{1}{2}\gamma_1 K_A H_1^2. With one dry layer, drop the 1s. The figure doesn't mark the H/3H/3, so carry that in.

Worked Example A 15 ft wall in dry sand
1 of 4

A retaining wall holds back 15 ft of level, dry sand with γ=120\gamma = 120 lb/ft³ and ϕ=32∘\phi = 32^\circ. Find the active pressure at its base, the active force per foot of wall, and that force's overturning moment about the base.

Passive resistance in front of the wall

Passive pressure is what holds a wall back. A wall shoved by its backfill tends to slide away from it, into the soil in front of its toe, and that soil pushes back. So does soil beside a footing shoved sideways, and soil in front of an anchor block that a tie rod pulls through the ground. The triangle is the same with KPK_P in it, but its height is only the depth of soil in contact, the embedment depth DD:

PP=12KPγD2P_P = \tfrac{1}{2}K_P\gamma D^2

It acts D/3D/3 above the bottom of the embedded face. The Handbook says only that passive forces are "similar to the active forces shown," so this is its active form with KPK_P and DD in place of KAK_A and HH. The height of the wall above doesn't enter. A 20 ft wall with 3 ft of soil in front of its toe gets passive help from those 3 ft only, and KPK_P being large is what makes even that much worth counting.

Wall PA PP Backfill Soil in front Wall tends to slide H D
Active pressure over the wall's height, passive over its embedment
The backfill pushes on the full height HH. The soil in front resists only over its own depth DD.
Checkpoint
1 of 2

A retaining wall holds back 14 ft of backfill. The bottom of its base is 3 ft below the ground surface in front of the toe, where the soil has γ=120\gamma = 120 lb/ft³ and ϕ=32∘\phi = 32^\circ. What passive resistance can the soil in front of the toe supply, per foot of wall?

lb/ft

What makes the push grow

Read the trends straight off P=12KγH2P = \tfrac{1}{2}K\gamma H^2. The unit weight appears once, so a heavier soil pushes harder in proportion. The height is squared: double it, and the triangle is twice as tall and twice as wide at its base, so it holds four times the area. The moment, whose arm H/3H/3 doubles too, grows eightfold.

The friction angle works only through KK, and in opposite directions. A soil with more friction holds more of itself up when the wall leans away, so KAK_A falls, and resists harder when it's shoved, so KPK_P rises. K0K_0 falls with ϕ\phi too. That's one reason retaining walls are backfilled with clean sand or gravel.

Checkpoint
1 of 2

The active force on an 8 ft retaining wall is 1.8 kip per foot of wall. A 12 ft wall holds back the same backfill. What is the active force on it?

kip/ft

Recap

  • Soil pushes sideways with a fraction of its vertical effective stress, σh′=Kσv′\sigma'_h = K\sigma'_v, with σv′=γz\sigma'_v = \gamma z in a dry backfill.
  • A wall that can't move gets K0≈1−sin⁡ϕK_0 \approx 1 - \sin\phi. Leaning away drops the push to KA=tan⁡2(45∘−ϕ/2)K_A = \tan^2(45^\circ - \phi/2), and pushing in raises it to KP=tan⁡2(45∘+ϕ/2)K_P = \tan^2(45^\circ + \phi/2), so KA<K0<KPK_A < K_0 < K_P. Full passive takes roughly ten times the movement active does.
  • Both limits are the triaxial failure ratio, with σv′\sigma'_v as σ1\sigma_1 for active and as σ3\sigma_3 for passive.
  • The pressure triangle gives P=12KγH2P = \tfrac{1}{2}K\gamma H^2 per unit length of wall, acting H/3H/3 above the base, with moment P(H/3)P(H/3). Passive resistance in front of a toe or anchor block uses the embedment depth: PP=12KPγD2P_P = \tfrac{1}{2}K_P\gamma D^2.
  • The force grows with H2H^2 and with γ\gamma. A higher ϕ\phi lowers the active force and raises the passive resistance.