Unit Weights of Soil
The same soil weighs more or less depending on how much water fills its voids.
Before this Lesson
How much does a cubic foot of soil weigh? For one particular sand, the honest answer is "when?" Bone dry, it weighs about 99 lb. Soaked, about 125 lb. Sunk below the water table, its grains press on each other with only about 62 lb. The grains never changed. All of those numbers come out of one box, one short expression, and one subtraction.
Dry means the grains alone
From Soil as Three Phases you already have two unit weights. The moist unit weight, which the Handbook's Phase Relationships section calls the total unit weight, counts everything: . The dry unit weight counts only the grains: . Both divide by the sample's whole volume. So "dry" doesn't mean anyone dried the soil. A soggy sample has a dry unit weight too. It just means you're leaving the water out of the count.
Water content connects the two. The water weighs times what the grains weigh, so . Divide both sides by and you have a conversion the Handbook leaves you to work out:
Here goes in as a decimal, so 15% is 0.15.
One expression for any amount of water
Often a question gives you no measured unit weight, only , , and how full the voids are. Those are ratios with no sample attached, so set and fill in the box, as you did in the last Lesson.
Box adapted from the FE Reference Handbook, Phase Relationships
The voids are , and water fills the fraction of them, so its volume is and its weight is . One unit of solid grain weighs times as much as the same volume of water, so the solids weigh . A unit weight is weight over volume, so read it off the box:
Grains plus water on top, total volume underneath. The Handbook doesn't print this general form, only the saturated case below, so the box is how you get it on exam day. When a question gives instead of , the from the last Lesson swaps one for the other.
Now treat as a dial, with and holding still. Turn it down to 0 and the water term vanishes. Turn it up to 1 and the voids are full:
The second is the form the Handbook prints, under Saturated unit weight. The first deserves a second look. There's no in it, because the dry unit weight never counted the water. Two samples of a soil at the same void ratio share one , however wet they are.
Take a sand with and , and the dial gives the Hook's numbers, plus one in between: 99 lb/ft³ dry, 112 half full, and 125 saturated. With , the same sand reads 15.6, 17.6, and 19.6 kN/m³.
Below the water table
The saturated unit weight is the full weight of a cubic foot of soaked soil, water included. Below the water table there's a second question: how hard do the grains press on each other? The box can't answer that alone, because the water is doing something a weight label doesn't show.
Hang one cubic foot of solid grain from a spring scale. With , it reads 168.5 lb. Lower it into a tank until it's under water, and the water pushes up with the weight of the water it shoves aside, 62.4 lb. The scale drops to 106.1 lb. That's Archimedes' principle, from Gates and Buoyancy, and every grain below the water table is in that tank.
Now put that cube back in the box. One unit of solids under water bears down with . What about the water in the voids? It's water sitting in water, and its weight is canceled by its own buoyancy, so it adds nothing. Spread what's left over the box's volume:
You don't need a new formula to get there. Subtract from the saturated form, and the 's cancel on top:
So , which is the line the Handbook prints, naming it the effective (submerged) unit weight. Most exam questions and textbooks say buoyant. For our sand it comes to 62.4 lb/ft³, or 9.81 kN/m³. That's exactly half of only because these numbers are friendly, but ordinary soils land close to it. Below the water table, about half of a soil's weight disappears as far as its grains can tell.
Working backward from a dry unit weight
Compaction tests report dry unit weights, so a question may hand you and and ask about the soil once it's soaked. When is known, and are one fact written two ways, so solve the dry form for :
Now you know the voids, and the voids are all you need. Filling them means , so the saturated form gives . And with , becomes , so the water content at saturation is .
Squeezing out the last of the air
Fix the water content and pack the soil tighter. For our sand at , the box with holds units of water, and packing can't change that. Only the air can leave. So the box shrinks from the top, the same grains sit in less volume, and the dry unit weight climbs. When the last of the air is gone, the box has nowhere left to go. That's the zero-air-voids condition, and it's a ceiling on the dry unit weight at that water content.
Zero air means , and the form takes two moves. Putting in gives . Putting that in the dry form gives
For our sand that's lb/ft³, up from 99.1 with the air in. It sounds odd to give a saturated soil a dry unit weight, but "dry" still means only that you're counting the grains alone. The Handbook neither prints this form nor mentions zero air voids. Some questions give you the form and others expect you to derive it, and those two moves are all it takes. The Proctor Test puts it to work.
Which one does the question want?
Questions rarely say "use the buoyant unit weight." They describe a situation and leave the choice to you. Two things settle it: where the soil sits relative to the water table, and what you're counting.
| Situation | Counting | Use |
|---|---|---|
| Above the water table | Grains and their water | |
| Below the water table | Grains and water | |
| Below the water table | Grain-on-grain push | |
| How tightly it's packed | Grains alone |
The Handbook's Vertical Stress Profiles follow the same rule, labeling the layer below the water level with its saturated unit weight. Turning these into stresses is the job of Effective Stress.
To rank the four for one soil, follow the water. Filling voids adds weight without adding volume. Going under water does more than take that added weight back, because it also lifts the grains themselves.