Aggregate Moisture States

Aggregate is a sponge, and saturated surface-dry is the sponge squeezed just right.

A batch plant's ticket calls for 290 lb of water per cubic yard, and the operator weighs out exactly that. On Monday, after a night of rain on the sand pile, the truck shows up soupy. On Friday, after a dry week, the same ticket comes out stiff. Nobody touched the recipe. The aggregate changed it, because rock and sand bring water of their own to the mix, or take some for themselves.

A rock is a stiff sponge

Aggregate looks solid, but a piece of gravel or a grain of sand is full of tiny pores, many of them open to the surface. So it can hold water in two places, and the difference between them drives this whole Lesson.

  • Absorbed water sits inside the pores. It's locked away from the cement, so it plays no part in the paste.
  • Free water sits on the surface. In the mixer it washes off and joins the paste, where it acts just like water from the hose.

As aggregate goes from bone-dry to dripping, the pores fill first and the surface gets wet after. That gives four named states.

empty pore absorbed water free water Oven-dry pores: empty surface: dry Air-dry pores: partly full surface: dry Saturated surface-dry pores: full surface: dry Wet pores: full surface: film of water
The four moisture states of one aggregate particle
Pores and the surface film are exaggerated so you can see them.
  • Oven-dry: baked until its weight stops changing. There's no water anywhere.
  • Air-dry: left out in the air. The surface is dry and the pores are partly full, so it feels dry without being empty.
  • Saturated surface-dry (SSD): pores full, surface dry. It's a soaked sponge wrung out just until your hand comes away dry. Nobody can wring a rock, so a lab soaks a gravel sample for about a day, then towels it until the shine of surface water is gone.
  • Wet: pores full, with a film of water on the surface. Sand after a rain is the usual example.

Why the recipe assumes saturated surface-dry

Now drop each state into a mixer and follow the water. A particle with room left in its pores soaks up mix water until the pores fill, and that water never reaches the cement. A particle with a film on its surface hands that film over to the paste. The one state that does neither is pores full and surface dry. It keeps what it has and asks for nothing.

That's why a concrete mix is proportioned as if every aggregate were SSD. The water on the design sheet is then the water the paste actually gets, and the water-cement ratio comes out as intended. SSD is also repeatable: a given aggregate's pores hold about the same water every time, while a stockpile's moisture changes with the weather. Real stockpiles rarely arrive at SSD, so the batch gets corrected for the difference, which is the job of Moisture Corrections to Batch Weights. The solid volumes in Absolute Volume Mix Design rest on the same basis.

Checkpoint
1 of 2

Which sketch shows air-dry aggregate?

A.
B.
C.
D.

Three percentages, one denominator

You can't see the water inside a rock, so you weigh it. Three weights of the same sample tell the whole story: as it comes from the stockpile (WstockW_{\text{stock}}), at SSD (WSSDW_{\text{SSD}}), and out of the oven (WODW_{\text{OD}}). The solids are the same every time, so the gap between any two weights is water.

drysolids absorbedwater freewater WOD WSSD Wstock Oven-dry SSD Stockpile Wstock −WSSD WSSD −WOD Wstock −WOD
The same solids, with water added in layers
The water layers are drawn far thicker than they are in real aggregate.

To turn a weight of water into a percentage, divide by the dry solids. The Handbook's Phase Relationships section prints that form for soil, as water content:

ω=WWWS×100\omega = \frac{W_W}{W_S} \times 100

Here WWW_W is the weight of water and WSW_S is the weight of solids, which for aggregate is WODW_{\text{OD}}. Why always the dry solids? Because they're the one thing in the sample that doesn't change. Water comes and goes with the weather, so a percentage of the wet weight is a percentage of a moving target. Put every weight of water over the same solids, and the percentages can be added and subtracted like dollars in one account.

The Handbook stops there, with nothing on aggregate moisture, so these three are yours to build from that one form. Each changes only which water goes on top: the water in full pores, all the water, or the water beyond what the pores hold.

absorption=WSSD−WODWOD×100total moisture=Wstock−WODWOD×100free moisture=Wstock−WSSDWOD×100\begin{aligned} \text{absorption} &= \frac{W_{\text{SSD}} - W_{\text{OD}}}{W_{\text{OD}}} \times 100 \\[6pt] \text{total moisture} &= \frac{W_{\text{stock}} - W_{\text{OD}}}{W_{\text{OD}}} \times 100 \\[6pt] \text{free moisture} &= \frac{W_{\text{stock}} - W_{\text{SSD}}}{W_{\text{OD}}} \times 100 \end{aligned}

You'll also see total moisture called simply moisture content, and free moisture called free surface moisture. Because all three share a denominator, free moisture is just total moisture minus absorption. For aggregate drier than SSD, that comes out negative, and it should: the rock isn't carrying extra water, it's short of water. Soils get the same water-over-dry-solids treatment in Soil as Three Phases.

Worked Example Three percentages from three weights
1 of 4

A gravel sample weighs 2,610 g from the stockpile, 2,550 g at SSD, and 2,500 g oven-dry. Find its absorption, total moisture content, and free moisture.

Will this stockpile give water or take it?

Now line the states up on one scale of moisture content. Oven-dry sits at zero. SSD sits at the aggregate's absorption, a property of the rock itself. Below that mark the aggregate is air-dry, and above it the aggregate is wet.

air-dry free moisture negative takes water from the mix wet free moisture positive gives water to the mix 0 oven-dry absorption saturated surface-dry moisture content (% of oven-dry weight)
The moisture states on one scale
The arrows show the aggregate settling toward SSD in the mixer.

So the question comes down to one comparison: moisture content against absorption. Above the absorption, the pores are already full, and the extra water has nowhere to go but the paste. Below it, the pores have room, and they fill from the mix water. Either way the rock settles at SSD, and the mix collects or pays the difference, which is the free moisture, as a percentage of the oven-dry weight. Turning that percentage into pounds of batch water belongs to the moisture corrections Lesson.

Checkpoint
1 of 2

A sand stockpile has an absorption of 1.4% and a moisture content of 3.9%. What does it do to the water in the mix?

A.
It adds water equal to 3.9% of its oven-dry weight.
B.
It takes water equal to 2.5% of its oven-dry weight.
C.
It adds water equal to 2.5% of its oven-dry weight.
D.
It neither adds nor takes water, since its pores are full.

Will the rock hold up?

So far the question has been what water a rock brings. A separate question is whether the rock itself will last, and two standard tests ask it in different ways. The Handbook prints nothing on either, so here's what you need. For each one, ask: what does the test measure?

Los Angeles abrasion: wear and degradation

The Los Angeles abrasion test is a rock tumbler with no mercy. A weighed sample of coarse aggregate goes into a steel drum with a charge of steel balls, and the drum turns, typically for 500 revolutions. A shelf inside keeps lifting the rock and balls and dropping them, so the pieces get smashed and ground against each other. Then a No. 12 sieve splits the result. What stays on the sieve survived, and what passes through has been worn away.

1. Tumble 2. Sieve shelf 500 revolutions aggregate steel balls retained No. 12 sieve passing: the loss
The Los Angeles abrasion test
abrasion loss=Woriginal−WretainedWoriginal×100\text{abrasion loss} = \frac{W_{\text{original}} - W_{\text{retained}}}{W_{\text{original}}} \times 100

The number reports the rock that got ground away, not the rock left over, so a lower loss means a more durable aggregate. It measures resistance to wear and degradation: the beating aggregate takes in handling, in the mixer, and under traffic.

Checkpoint

A 5,000 g sample goes through the Los Angeles abrasion test, and 3,850 g is retained on the No. 12 sieve afterward. What is the abrasion loss?

%

Sulfate soundness: weathering

Wear isn't the only thing that breaks a rock. Water in those same pores freezes and expands, winter after winter, and a weak pore structure cracks apart. Nobody wants to wait for real winters, so the sulfate soundness test speeds things up. Soak the sample in a sodium or magnesium sulfate solution, then dry it in an oven, and salt crystals grow in the pores and push on the walls the way ice would. After several cycles, commonly five, sieve it and report the mass lost. Again, a lower loss is better, and here it means more resistance to weathering.

Checkpoint
1 of 2

A specification caps the Los Angeles abrasion loss. Aggregate A loses 19% and aggregate B loses 41%. What does the cap guard against, and which aggregate does better?

A.
Weathering from freezing and thawing; aggregate A
B.
Wear and degradation; aggregate B
C.
Wear and degradation; aggregate A
D.
Water absorption; aggregate B

Recap

  • Aggregate holds absorbed water in its pores, locked away from the cement, and free water on its surface, which joins the paste.
  • The four states run oven-dry, air-dry, saturated surface-dry, and wet. SSD neither gives water to the mix nor takes it, so it's the reference for mix proportions.
  • Absorption, total moisture, and free moisture all divide by the oven-dry weight, because the dry solids never change. Free moisture is total moisture minus absorption.
  • Moisture above the absorption gives water to the mix. Moisture below it takes water, even from a pile that looks dry.
  • Los Angeles abrasion loss is the mass lost over the original mass, and it measures wear and degradation. Sulfate soundness measures weathering. For both, a lower loss is better.