Axial Deformation

Every segment stretches by its own share, and the shares add.

Hang a 3,000 lb car from a steel rod 1 in. thick and 20 ft long, and the rod gets longer by about 0.03 in., the thickness of a credit card. Hang a second car, and the stretch doubles. Lift both off, and the rod goes back to exactly where it started. That's how a spring behaves. A steel rod is a spring, a very stiff one, and once you know how stiff, you can say how far anything built from rods will move.

A bar is a stiff spring

Three things you already know snap together. The force spreads over the area, σ=P/A\sigma = P/A. Hooke's law turns that stress into strain, ε=σ/E\varepsilon = \sigma/E. And strain is stretch per length, so the whole bar stretches δ=εL\delta = \varepsilon L. Chain them:

δ=εL=σEL=PA⋅LE=PLAE\delta = \varepsilon L = \frac{\sigma}{E}L = \frac{P}{A}\cdot\frac{L}{E} = \frac{PL}{AE}

The Handbook prints the result under Uniaxial Loading and Deformation, where it calls δ\delta the elastic longitudinal deformation. "Elastic" is the fine print: the chain runs through Hooke's law, so it holds only up to the proportional limit.

Now rearrange it. A spring obeys F=kxF = kx, so its stretch is its force divided by its stiffness. The bar's formula has the same shape:

δ=PAE/L\delta = \frac{P}{AE/L}

So a bar is a spring with stiffness AE/LAE/L, its axial stiffness: the force it takes per unit of stretch. The Handbook never prints AE/LAE/L, but it's one rearrangement away, and the picture is worth carrying.

rod spring area A, modulus E L k = AE/L δ P δ P δ = P/k
A rod and a spring under the same load

Each letter does what your hands would expect. A fatter bar has more strands sharing the pull. A stiffer material gives less. A longer bar is softer, because every inch stretches the same and there are more inches. The Hook's rod has AE/L=(0.785 in2)(29,000 ksi)/(240 in.)=95 kip/in.AE/L = (0.785\ \text{in}^2)(29{,}000\ \text{ksi})/(240\ \text{in.}) = 95\ \text{kip/in.} Divide the car's 3 kip by that, and you get the 0.03 in.

The sign follows the force. The Handbook's entry has no sign rule, so this topic's carries over: tension is positive, so a positive δ\delta is an elongation, and compression is negative, so a negative δ\delta is a shortening.

The formula converts nothing for you, so pick one family and put every number in it. A length left in feet is the classic way to wreck the answer.

Two unit families that work in PL/AE
ForceLengths and δAreaE
kipin.in²ksi
Nmmmm²MPa

Here are the moduli in those units. Table 1 prints Mpsi and GPa, so 29.0 Mpsi is 29,000 ksi, and 200 GPa is 200,000 MPa. Table 2 prints 10310^3 ksi and has no SI values. Its A36 and 6061-T6 match the steel and aluminum rows here.

Modulus of elasticity, in the units of each family
MaterialTableE (ksi)E (MPa)
Steel129,000200,000
Aluminum110,00069,000
Cast iron114,500100,000
Brass114,800–18,100102,000–125,000
Red brass C83400214,600—

Source: FE Reference Handbook, Table 1 - Typical Material Properties and Table 2 - Average Mechanical Properties of Typical Engineering Materials (adapted)

Worked Example A steel hanger
1 of 2

A steel rod, 3/4 in. in diameter and 12 ft long, carries 8 kip in tension. Using Table 1, find how much it stretches.

Squeezing a hollow post

Push on the spring instead of pulling, and it shortens by the same rule, with PP and δ\delta both negative. A short post just squashes this way. A slender one can buckle first, which waits for Euler Buckling.

Two things need care in a hollow post. The first is the area. The load travels down through the metal, not the hole, so the stiffness comes from the ring:

A=π(D2−d2)4A = \frac{\pi(D^2 - d^2)}{4}
P L d D A = π(D² − d²)/4
A short hollow post and the ring that carries its load

The second is which EE. Use Table 2 for an alloy it lists, and Table 1 for anything else. Table 1 gives plain brass only a range, so a brass question either names an alloy, such as red brass C83400, or states EE.

Checkpoint
1 of 2

A short hollow cast iron post has a 150 mm outside diameter and a 15 mm wall. It is 1.5 m tall and carries a 400 kN compressive load. Using Table 1, how much does it shorten? Enter the shortening as a positive number.

mm

Running it backward

Sometimes the stretch is what's given. A hanger may be allowed to drop only a tenth of an inch, and the question is how thick it has to be, or how much it can carry.

Turn the spring around. A load PP and a limit δmax⁡\delta_{\max} together set the least stiffness the rod can have, P/δmax⁡P/\delta_{\max}. Set AE/LAE/L equal to that and solve for whichever letter is missing:

Amin⁡=PLE δmax⁡Pmax⁡=AEL δmax⁡A_{\min} = \frac{PL}{E\,\delta_{\max}} \qquad\qquad P_{\max} = \frac{AE}{L}\,\delta_{\max}

From the area, the diameter is d=4A/πd = \sqrt{4A/\pi}. A thinner rod stretches more, so this diameter is a floor: if a question offers sizes, take the first one above it, even when a smaller one is closer.

Worked Example The thinnest rod that stays within its limit
1 of 3

A steel rod, 15 ft long, carries 20 kip in tension and may stretch no more than 0.10 in. Using Table 1, find its minimum diameter.

Changing one thing at a time

Some questions give no numbers at all: what happens to the stretch if the rod is twice as long? You don't need to compute anything. In δ=PL/AE\delta = PL/AE, each letter on top pushes the stretch up in proportion, and each letter below pulls it down in proportion. Write new over old, and whatever didn't change cancels:

δnewδold=PnewPold⋅LnewLold⋅AoldAnew⋅EoldEnew\frac{\delta_{\text{new}}}{\delta_{\text{old}}} = \frac{P_{\text{new}}}{P_{\text{old}}}\cdot\frac{L_{\text{new}}}{L_{\text{old}}}\cdot\frac{A_{\text{old}}}{A_{\text{new}}}\cdot\frac{E_{\text{old}}}{E_{\text{new}}}

Triple the load or the length, and the stretch triples. The diameter takes more care, because it reaches the formula through the area, which goes with its square. Cut a rod's diameter to a third, and the area falls to a ninth, so the stretch grows ninefold. For a change of material, compare the moduli: put cast iron in place of steel, and the stretch grows by 29.0/14.5 = 2.

Checkpoint
1 of 3

A rod's diameter is doubled, with the same length, material, and load. What happens to its elongation?

A.
It falls to half.
B.
It falls to an eighth.
C.
It doubles.
D.
It falls to a quarter.

Here's all of it in one picture, with the same load on every rod.

starting rod steel twice as long steel twice as thick steel same size aluminum δ P 2δ P δ/4 P 2.9δ P
One steel rod and three changes to it, under the same load

Segments in a line

A stepped bar is springs in a row. Fix one end, pull the other, and watch the joint between two segments. The near segment stretches by its share, and since the far segment is attached to it, that stretch carries the whole far segment along. Then the far segment adds its own share on top. So the free end moves by the sum.

no load segment 1 segment 2 under load P δ1 δ1 + δ2 δ2
Two segments in a line, before and under load

Each segment is its own spring, with its own length, area, and material. It also has its own internal force, which is rarely the load beside it:

δtotal=∑iPiLiAiEi\delta_{\text{total}} = \sum_i \frac{P_i L_i}{A_i E_i}

That's the statics half and then the materials half: cut each segment for its force, then divide that force by the segment's stiffness. Keep the signs, because a segment in compression shortens and its share subtracts. The Handbook prints only the single-bar formula, so the sum is yours to carry in. It comes back, over the members of a truss, in Truss Deflection by Virtual Work.

Worked Example Three segments, loads both ways
1 of 3

You may recognize the areas and loads of this steel bar from Axial Stress. It now has lengths. Using Table 1, find its total change in length.

40 kip 36 kip 8 kip A B C D 3 in², 4 ft 2 in², 3 ft 1 in², 5 ft
A stepped steel bar fixed at A, with loads at B, C, and D

A rigid bar on an elastic rod

Pin a rigid bar at one end, hold it up with a rod, and load it. The rod is the only thing that gives. As it stretches, the bar swings down about the pin, staying perfectly straight.

A straight bar turning about a point has one thing it can do: change its angle. So every point on it moves by that angle times its distance from the pin. Twice as far from the pin means twice the drop. The angles here are tiny, so each point's move is effectively straight down.

rod δB δC rod's stretch = δB P A B C xB xC
A rigid bar turning about its pin, with the rotation exaggerated

The point where the rod attaches moves by exactly the rod's stretch. Any other point scales from there, by similar triangles that share the angle at the pin:

δCxC=δBxB\frac{\delta_C}{x_C} = \frac{\delta_B}{x_B}

The Handbook has no entry for this setup, so you build it from three steps:

  1. Statics half. Sum moments about the pin, which leaves the rod's force TT as the only unknown.
  2. Materials half. Find the rod's stretch, δB=TL/AE\delta_B = TL/AE, with the rod's own length, area, and material.
  3. Geometry. Scale by the ratio of distances from the pin. A point farther out than the rod moves more than the rod stretches, and a point closer in moves less.
Worked Example A load at the end of the bar
1 of 3

The rod is steel. Using Table 1, find the rod's force, its stretch, and how far point C moves down.

rod: 1.5 in², 8 ft 18 kip A B C rigid bar 6 ft 4 ft
A rigid bar pinned at A and held by a rod at B

Recap

  • A bar is a stiff spring with axial stiffness AE/LAE/L, so δ=PL/AE\delta = PL/AE. Tension stretches it and compression shortens it. Keep kips, inches, and ksi together, or newtons, millimeters, and MPa. A hollow post carries its load in the ring, A=π(D2−d2)/4A = \pi(D^2 - d^2)/4.
  • For a stretch limit, run it backward: Amin⁡=PL/(E δmax⁡)A_{\min} = PL/(E\,\delta_{\max}) and d=4A/πd = \sqrt{4A/\pi}, or Pmax⁡=(AE/L) δmax⁡P_{\max} = (AE/L)\,\delta_{\max}.
  • The stretch goes with LL, with one over EE, and with one over the diameter squared. Twice the diameter means a quarter of the stretch.
  • Segments in a line each stretch by their own share, from their own internal force, and the signed shares add: δtotal=∑PL/AE\delta_{\text{total}} = \sum PL/AE.
  • A rigid bar only rotates about its pin, so every point's displacement is proportional to its distance from the pin. Find the rod's force from moments, its stretch from PL/AE, then scale.