Centroids of Areas

The centroid is the balance point of a shape cut from thin plate.

Before this Lesson

Cut an L out of stiff cardboard, push a pin through one end, and let it hang. It swings until its balance point sits straight below the pin, so a plumb line from the pin runs through that point. Mark the line, hang the L from somewhere else, and mark again. The two lines cross at the balance point, and for a thin L, that's out in the notch, where there's no cardboard at all.

pin plumb line pin plumb line first line C
Two plumb lines cross at the balance point

A short table finds the same spot without the cardboard, and you'll need it again: a beam bends about a line through its cross section's centroid.

A balance point is a weighted average

Set a 1 lb weight at the 2 ft mark of a weightless plank and a 2 lb weight at the 8 ft mark. The balance point isn't halfway, at 5 ft, because the heavier weight pulls it closer. Count each position by its weight:

(1)(2)+(2)(8)1+2=6 ft\frac{(1)(2) + (2)(8)}{1 + 2} = 6\ \text{ft}

From the 6 ft mark, the left weight acts 4 ft out and the right one 2 ft out, so (1)(4) and (2)(2) make 4 lb·ft each, twisting opposite ways: a standoff.

Now take a uniform 12 ft plank, which obviously balances at its middle, and saw it at the 4 ft mark. The short piece has its middle at 2 ft, and the long piece, twice as heavy, has its middle at 8 ft. That's the same calculation, and it gives the plank's middle. So you can cut a body into pieces, treat each as a lump at its own balance point, and take the weighted average. Where you cut makes no difference.

uniform plank W 2W 0 2 4 6 8 10 12 ft
A plank sawn in two balances in the same place

A flat plate of uniform thickness weighs in proportion to its area, so area can stand in for weight, and the balance point becomes pure geometry: the centroid. The Handbook's Statics chapter prints it under Centroids of Masses, Areas, Lengths, and Volumes:

xac=∑xnanAyac=∑ynanAA=∑anx_{ac} = \frac{\sum x_n a_n}{A} \qquad y_{ac} = \frac{\sum y_n a_n}{A} \qquad A = \sum a_n

Here ana_n is one part's area, and xnx_n and yny_n locate that part's own centroid. Each product, such as ynany_n a_n, is the part's first moment of area: its area times its distance from an axis.

Cut, tabulate, divide

Take a T-shaped section: a 12 in by 2 in flange on a 2 in by 8 in stem. Its vertical mirror line settles xacx_{ac} (you'll see why shortly), so only the height is in question. Cut it into two rectangles, whose centroids sit at their middles, and measure from one reference line, here the bottom edge.

reference line flange stem 12 in 2 in 2 in 8 in y1 = 4 in y2 = 9 in yac = 7.00 in C
A T-section cut into a stem and a flange
The T-section, part by part, from the bottom edge
Partana_n (in²)yny_n (in)ynany_n a_n (in³)
1: Stem16464
2: Flange249216
Sum40280
yac=∑ynanA=28040=7.00 in above the bottom edgey_{ac} = \frac{\sum y_n a_n}{A} = \frac{280}{40} = 7.00\ \text{in above the bottom edge}

That table is the method, and you'll add columns to it for moment of inertia. Two habits keep it honest. Every yny_n runs from the same reference line: the flange's centroid is 9 in above the bottom edge, not 1 in above its own lower edge. And parts can't overlap: the stem stops where the flange starts.

Then check. With solid parts, the result has to land between the smallest and largest yny_n, and with two parts, nearer the bigger one. Here, 7 falls between 4 and 9, nearer the flange.

Worked Example An L-section, both ways
1 of 3

An L-section has a 10 in bottom leg and an 8 in side leg, each 2 in thick. Find its centroid from the left and bottom edges.

x y 10 in 8 in 2 in 2 in
An L-section with unequal legs

A hole is a part with a minus sign

The Handbook never mentions holes, and its A=∑anA = \sum a_n shows no minus sign, so here's the reasoning. Put the plug back in the hole. The full plate is now two parts, the plate with its hole and the plug, and their first moments have to add up to the full plate's. Solve that for the plate with its hole, whose area is afull−apluga_{\text{full}} - a_{\text{plug}}:

yac=yfull afull−yplug aplugafull−aplugy_{ac} = \frac{y_{\text{full}}\,a_{\text{full}} - y_{\text{plug}}\,a_{\text{plug}}}{a_{\text{full}} - a_{\text{plug}}}

So a hole goes in the table as a part with negative area. Its yny_n stays an ordinary position, its product comes out negative, and the minus sign shows up both above and below the fraction. That's the list of pluses and minuses from Areas of Plane Figures, with positions attached.

Test it on the L you just solved, which is also a 10 in by 8 in rectangle missing an 8 in by 6 in corner centered 6 in from the left edge:

xac=(5)(80)−(6)(48)80−48=11232=3.50 inx_{ac} = \frac{(5)(80) - (6)(48)}{80 - 48} = \frac{112}{32} = 3.50\ \text{in}

It's the same answer from a different cut.

Worked Example A plate with a round hole
1 of 3

A 12 in by 8 in plate has a 4 in diameter hole centered 9 in from the left edge and 5 in above the bottom edge. Locate its centroid from those two edges.

x y 9 in 5 in 12 in 8 in 4 in dia.
A plate with a circular hole

Answers without arithmetic

Some centroid questions want no numbers. Two ideas cover them, and the Handbook states neither.

Symmetry. Every bit of area on one side of a mirror line, or axis of symmetry, has a twin the same distance out on the other, so their first moments about the line cancel. So the centroid lies on every mirror line. With two mirror lines, it's where they cross. With one, that coordinate is free and you compute the other.

Adding and cutting. Add area, and the centroid moves toward it. Cut a hole, and it moves away. Either way it travels along the line through the old centroid and the part's centroid, and a bigger part or one farther out moves it more. A hole centered exactly on the old centroid doesn't move it at all, just as removing a score equal to the class average leaves the average alone.

Add area added part old C new C Cut a hole hole old C new C
Added area pulls the centroid in, and a hole pushes it away
Checkpoint
1 of 3

In which of these sections does the centroid sit exactly halfway across the width, with no calculation needed?

A.
B.
C.
D.

The area table gives one shape at a time

So far, every part has been a rectangle or a circle, with its centroid at its middle. Other shapes come from a table in the Handbook's Statics chapter. It has no printed title, only columns that begin Figure and Area & Centroid, and the index lists it under centroids and moments of inertia. I'll call it the area table. It writes xcx_c and ycy_c for a single shape.

Each row's xcx_c and ycy_c run from the axes in that row's own figure, which may not be your axes, so read the figure before you trust the formula. Two rows show a right triangle facing opposite ways, and one says xc=2b/3x_c = 2b/3 while the other says b/3b/3. They agree: both centroids are a third of the base from the tall leg, but the yy-axis sits at the sharp corner in one and on the tall leg in the other.

Right angle at far end x y b h xc yc C Right angle at origin x y b h xc yc C Trapezoid x y b a h yc C
Two triangle rows and the trapezoid, with each row's axes

Adapted from the FE Reference Handbook, Statics area table

The straight-edged rows
RowAAxcx_cycy_c
Right angle at far endbh/2bh/22b/32b/3h/3h/3
Right angle at originbh/2bh/2b/3b/3h/3h/3
Trapezoidh(a+b)/2h(a + b)/2not printedh(2a+b)3(a+b)\dfrac{h(2a + b)}{3(a + b)}

Adapted from the FE Reference Handbook, Statics area table

A triangle's area piles up near its base, so its balance point sits low: a third of the way up from the base, and two-thirds of the way down from the tip. Any side can play the base, so the centroid is a third of the way from each side toward the opposite corner.

The trapezoid's ycy_c runs from the side it calls bb. Test the formula on shapes you know: a=ba = b gives h/2h/2, a rectangle, and a=0a = 0 gives h/3h/3, a triangle.

Read the letters row by row

In the formula, ana_n is an area, but in the table's rows, aa is a length: the trapezoid's top side, or the radius of anything circular.

The curved rows bring their own traps:

  • A semicircle's yc=4a/(3π)y_c = 4a/(3\pi), about 0.424a0.424a, runs from the straight edge, never from the arc.
  • A sector's θ\theta is half its total angle, so it's half the φ\varphi that Mensuration of Areas and Volumes uses. The table doesn't say so, but it has to be in radians. Its xcx_c runs from the circle's center along the sector's center line.
  • The parabolic spandrel, a word the Handbook doesn't use, is the row called nth degree parabola with n=2n = 2. That row prints its formulas for any nn, and the table below sets n=2n = 2.
Semicircle x y 2a a xc yc C Circular sector x y a θ θ xc C nth degree parabola x y b h y = (h/bn)xn xc yc C
Three curved rows, with each row's axes

Adapted from the FE Reference Handbook, Statics area table

The curved rows
RowAAxcx_cycy_c
Semicircleπa2/2\pi a^2/2aa4a3π\dfrac{4a}{3\pi}
Circular sectora2θa^2\theta2a3⋅sin⁡θθ\dfrac{2a}{3}\cdot\dfrac{\sin\theta}{\theta}00
nth degree parabola, n = 2bh/3bh/33b/43b/43h/103h/10

Adapted from the FE Reference Handbook, Statics area table

Worked Example A triangle on someone else's axes
1 of 4

Locate this triangle's centroid, measured from the axes shown.

x y O 9 in 6 in
A right triangle with its right angle at the upper right

Curved parts in a composite

A composite with a slanted or curved part works just like the T. The table gives each part's centroid from the part's own edge, so your one extra job is converting to a distance from the common reference line. A semicircle sitting on a rectangle of height hh has y2=h+4a/(3π)y_2 = h + 4a/(3\pi). Cut the same semicircle down out of the rectangle's top, and it counts negative, with y2=h−4a/(3π)y_2 = h - 4a/(3\pi), because its flat edge is now on top.

The table has no quarter-circle row, and it doesn't need one. Two quarter circles side by side make a semicircle, as mirror images at the same height, so each one's centroid is as high as the semicircle's: 4a/(3π)4a/(3\pi) from the flat edge. A quarter circle also mirrors across its diagonal, so its centroid is that far from its other straight edge too. Its area is πa2/4\pi a^2/4.

4a/(3π) a 4a/(3π) 4a/(3π) a
A quarter circle's centroid, from the semicircle and a mirror line
Worked Example A rectangle capped by a semicircle
1 of 4

A plate is a rectangle 8 in wide and 6 in tall, capped by a semicircle across its full width. How far above the bottom edge is its centroid?

bottom edge 8 in 6 in
A rectangle capped by a semicircle

Working backward to a dimension

Some problems name where the centroid has to be and ask for the dimension that puts it there. The equation doesn't change. It just has a letter in it, in the area, the position, or both. Multiply through by the total area to clear the fraction, and solve.

Worked Example How wide a flange?
1 of 3

A T-section has a 2 in by 8 in stem and a flange 2 in thick. How wide must the flange be to put the centroid 6.5 in above the bottom edge?

bottom edge b 2 in 2 in 8 in 6.5 in C
A T-section with an unknown flange width

The same average with other weights

Nothing in the average cared that the weights were areas. Loads on a platform count by their size, and the result is the center of gravity. The Handbook's Centroids of Masses, Areas, Lengths, and Volumes section opens with the mass version, rc=∑mnrn/∑mn\mathbf{r}_c = \sum m_n \mathbf{r}_n / \sum m_n, a vector equation you read one coordinate at a time. Weights give the same answer, because the same gg multiplies every mass and cancels.

A wire counts each straight piece by its length, acting at its midpoint. That section prints no formula for weights or lengths and never says center of gravity, so here are the versions you'll use:

xc=∑Wnxn∑Wnxc=∑Lnxn∑Lnx_c = \frac{\sum W_n x_n}{\sum W_n} \qquad x_c = \frac{\sum L_n x_n}{\sum L_n}
Worked Example A wire with a bend
1 of 4

A wire runs straight along the xx-axis from the origin to (8, 0), then bends and runs straight to (11, 4), in inches. Locate its center of gravity.

x y 8 in 3 in 4 in (8, 0) (11, 4)
A wire bent into two straight pieces

Recap

  • A centroid is a weighted average of position: yac=∑ynan/Ay_{ac} = \sum y_n a_n / A, with each part counted by its area at its own centroid.
  • Tabulate ana_n, yny_n, and ynany_n a_n from one reference line, with parts that don't overlap. A hole is a part with negative area.
  • The centroid lies on every axis of symmetry. Added area pulls it in, and a hole pushes it away.
  • The area table measures from each row's own axes. A triangle's centroid is a third of the way from a side, a semicircle's or quarter circle's is 4a/(3π)4a/(3\pi) from a straight edge, and a sector's θ\theta is a half-angle in radians.
  • To find a dimension, put a letter in the same equation. For loads, masses, and wires, weight the average by weight, mass, or length.