Back

Statics

  • Topic 4
  • 14 Lessons

Overview

Nothing in statics accelerates, and that one fact does nearly all the work in this topic. A leftover force would start a body sliding, and a leftover moment, a force's turning effect, would start it turning. So on anything held still, the forces and moments cancel exactly. That goes for every piece of it, too: a whole bridge, one joint of that bridge, and the half you'd get by sawing it in two all obey the same rule.

So nearly every problem here comes down to one habit: isolate, draw, sum to zero. Put a line around a piece, draw everything that touches it as a force, and make the forces and moments sum to zero, taking moments where they wipe out the most unknowns. The skill is choosing which piece to isolate and which point to take moments about.

Here's that habit on a drawbridge deck held partway open by a cable, when what you want is the cable's tension. It carries three of the topic's four big ideas.

1. Isolate tower cable deck hinge 2. Draw T W Hx Hy 3. Sum to zero moments about the hinge T W Hx Hy T’s arm W’s arm no arm moment point
Isolate, draw, sum to zero on a drawbridge deck

Isolate the body and draw it. Put a line around the deck and forget everything outside it. Whatever crossed that line now has to appear as a force, and so does gravity: the cable's pull TT, the deck's weight WW at its middle, and the hinge's push. You don't know which way the hinge pushes, so it gets two unknown parts, HxH_x and HyH_y. That sketch is the free-body diagram. You choose where the line goes: around a whole structure, around one knot in a rope, or through the middle of a bridge with the far side thrown away. The Handbook names the free-body diagram but never shows you how to draw one, so this part you bring with you.

Sum forces and moments to zero. A body in a plane can move in exactly three ways: slide sideways, slide up and down, or turn. It's doing none of them, so each body gives three equations, ΣFx=0\Sigma F_x = 0, ΣFy=0\Sigma F_y = 0, and ΣM=0\Sigma M = 0, which can settle at most three unknowns. The deck has exactly three. The Handbook's Equilibrium Requirements print the same rule in vector form. When every force on a body meets at one point, as at that knot, nothing can turn it, and you're left with the two force equations.

Choose where to take moments. You could solve all three equations together, but there's a better move. A force whose line runs through a point has no lever arm about that point, so it can't turn anything about it. Take moments about the hinge, and HxH_x and HyH_y vanish. All that's left is TT times its arm balancing WW times its arm: one equation, one unknown. Hunting for the point that wipes out the most unknowns is what turns a system of equations into one line.

Describe how the area is spread out. The fourth idea is a different kind of question. Centroids and moments of inertia don't come from summing forces at all. They're geometry: a shape's balance point, and how far its area lies from an axis. Take 24 in² of steel. Rearrange a solid bar into an I, with half the steel pushed out to the top and bottom, and you get about nine times the moment of inertia, which makes it about nine times as stiff against bending about that axis. Same steel, same loads. Only the spread changed, and no force diagram would show it. The Handbook's area table gives both properties for standard shapes.

axis through the centroid 4 in 6 in 6 in 14 in 1 in 1 in solid bar A = 24 in2 I = 72 in4 I shape A = 24 in2 I = 652 in4
The same 24 in² of steel, spread two ways
II is the moment of inertia about the dashed axis.

Most problems use several of these at once, but each usually turns on one of them. Try naming it.

Checkpoint
1 of 4

A sign hangs from a ring, and two cables run from the ring up and out to either side. You want the tension in each cable. What does this call for?

A.
Choosing where to take moments: about the ring, where both tensions meet
B.
Summing forces to zero at the ring, since every force meets there
C.
Working out how the sign's area is spread out

The Lessons below start with the tools: forces, knots held still, moments, and spread-out loads. Then comes the free-body diagram, and then the habit at work on beams, brackets, trusses, frames, and blocks held by friction. The last three turn to the geometry of areas.