Static Friction

Friction is only as large as it needs to be, until it can't be any larger.

A 100 lb crate sits on a level floor, and the coefficient of static friction between them is 0.4. Nobody's touching it. How much friction does the floor put on the crate? You have a coefficient and a normal force, so 40 lb looks like the obvious answer. But picture what a 40 lb sideways force does with nothing to oppose it: the crate would set off across the floor on its own. So what's wrong with the obvious answer?

Friction takes only what it needs

The answer is zero. Nothing pushes the crate sideways, so ΣFx=0\Sigma F_x = 0 leaves friction nothing to do. Push with 10 lb, and friction answers with 10 lb the other way. Static friction is a reaction, like the force at a pin: it takes whatever value equilibrium asks for.

Unlike a pin, it has a ceiling. The harder two surfaces are pressed together, the harder they can grip, so the ceiling is proportional to the normal force, and the area of contact doesn't enter. The Handbook's Statics chapter, under Friction, calls this ceiling the limiting friction:

F≤μsNF \le \mu_s N

Here FF is the friction force, NN is the normal force between the surfaces, and μs\mu_s is the coefficient of static friction. The Handbook has no table of coefficients, so a problem always gives you μs\mu_s. For the crate, the ceiling is 0.4(100)=40 lb0.4(100) = 40\ \text{lb}.

0 10 20 30 40 50 60 0 10 20 30 40 50 Push, P (lb) Friction, F (lb) Ceiling: μs N = 40 lb Slip impends Nobody pushing: F = 0 Push 25 lb: F = 25 lb Crate slides
The crate's friction as the push grows

The instant friction reaches its ceiling is called impending slip, and it's the only moment you may write F=μsNF = \mu_s N. The Handbook's Dynamics chapter says so in those words, also under Friction. Problems signal it with phrases like "just starts to move." Past that point the crate is moving, and moving bodies belong to Newton's Second Law.

Which way does friction point? It opposes the slide that would happen without it. So erase friction in your head, see which way the body would go, and point friction the other way.

Does it slide?

That gives a test for any body at rest. Find the friction equilibrium needs, then the friction available, μsN\mu_s N. If the need fits under the ceiling, the body stays, and friction equals the need. If not, it slides.

On a rough incline, the need comes from the weight. In Equilibrium of a Particle, a cable along the slope held a roller with T=Wsin⁡θT = W\sin\theta while the surface carried N=Wcos⁡θN = W\cos\theta. Swap the cable for friction, and nothing else changes:

Fneeded=Wsin⁡θFmax⁡=μsN=μsWcos⁡θF_{\text{needed}} = W\sin\theta \qquad F_{\max} = \mu_s N = \mu_s W\cos\theta

The Handbook prints neither. Notice that NN isn't WW: the surface carries only the part of the weight aimed into it.

θ θ W W cos θ W sin θ N F
A block at rest on a rough incline
Worked Example Does this block slide?
1 of 3

A 120 lb block rests on a 20° incline with μs=0.50\mu_s = 0.50. Does it slide, and what is the friction force?

Tilt the board

Set a block on a board and lift one end slowly. The need, Wsin⁡θW\sin\theta, grows. The ceiling, μsWcos⁡θ\mu_s W\cos\theta, shrinks. At some angle they meet, and the block goes:

Wsin⁡θ=μsWcos⁡θ⇒tan⁡θ=μsW\sin\theta = \mu_s W\cos\theta \quad\Rightarrow\quad \tan\theta = \mu_s

The weight canceled, so a heavy block and a light one of the same material let go at the same angle. That angle belongs to the pair of surfaces, and it's called the angle of friction, ϕ\phi:

tan⁡ϕ=μs\tan\phi = \mu_s

So a block on an incline stays if θ≤ϕ\theta \le \phi and slides if θ>ϕ\theta > \phi, and you don't need the weight to say which.

The Handbook never names this angle, and μ=tan⁡ϕ\mu = \tan\phi appears only in its Screw Thread entry. You'll meet the idea again in Shear Strength, where soil resists shear with normal force times the tangent of a friction angle.

Checkpoint
1 of 3

A 40 lb crate and a 400 lb crate sit on the same 20° ramp, each with μs=0.35\mu_s = 0.35. What happens?

A.
Neither slides.
B.
Only the 40 lb crate slides.
C.
Only the 400 lb crate slides.
D.
Both slide.

Friction can point either way

Now hold a block on a steep slope with a force PP parallel to it. There are two ways to lose. Pull too gently, and the block starts down, so friction points up the slope and helps you. Pull too hard, and it starts up, so friction flips and fights you. At each limit, friction is at its full μsN\mu_s N:

Phold=Wsin⁡θ−μsWcos⁡θPstart=Wsin⁡θ+μsWcos⁡θP_{\text{hold}} = W\sin\theta - \mu_s W\cos\theta \qquad P_{\text{start}} = W\sin\theta + \mu_s W\cos\theta

Between those two, the block stays put and friction covers the difference. If θ<ϕ\theta < \phi, PholdP_{\text{hold}} comes out negative, which just means the block holds itself and needs no help.

θ W N Phold μs N impending motion About to slide down θ W N Pstart μs N impending motion About to start up
The same block, about to go each way

A horizontal push is more awkward. Part of it, Pcos⁡θP\cos\theta, drives the block along the slope. The other part, Psin⁡θP\sin\theta, presses the block into the slope, which raises the ceiling:

N=Wcos⁡θ+Psin⁡θN = W\cos\theta + P\sin\theta

Now PP hides inside the friction too. Point friction against the way the block is about to go, write the equation along the slope and the equation normal to it, and solve them together, by hand or with a calculator's system solver.

θ θ P P cos θ P sin θ W N μs N
A horizontal push, about to start the block up the slope
Worked Example A horizontal push up an incline
1 of 3

A 300 lb block sits on a 25° incline with μs=0.35\mu_s = 0.35. What horizontal force PP just starts it up the slope?

An angled force changes the normal force

Back on a level floor, tilt the force. Pull with a rope angled up, and its vertical part lifts some of the crate, so the ceiling drops. Push down at an angle, and the vertical part presses the crate into the floor, so the ceiling rises:

N=W−Psin⁡α  (pull)N=W+Psin⁡α  (push)N = W - P\sin\alpha\ \ \text{(pull)} \qquad N = W + P\sin\alpha\ \ \text{(push)}
W N F α P P cos α P sin α N = W − P sin α Pull W N F α P P cos α P sin α N = W + P sin α Push
A pull lifts the crate, and a push presses it down

At impending slip, the horizontal part of PP equals μsN\mu_s N. A 200 lb crate with μs=0.40\mu_s = 0.40 and a rope 30° above the floor gives:

Pcos⁡30∘=0.40(200−Psin⁡30∘)⇒P=75.0 lbP\cos 30^\circ = 0.40(200 - P\sin 30^\circ) \quad\Rightarrow\quad P = 75.0\ \text{lb}

Pretending N=WN = W gives 92.4 lb, and pushing at the same angle takes 120 lb. That's the reason to pull a heavy sled and not push it.

Checkpoint

A 500 N crate sits on a level floor with μs=0.30\mu_s = 0.30. A force pushes on it, angled 20° below horizontal. What force just starts it sliding?

N

Friction at every surface that can slide

Stacks and tied blocks are still isolate, draw, sum to zero, one block at a time. Every surface that could slide gets its own friction force, equal and opposite on the two bodies it touches. And each NN comes from what that surface actually carries, so the surface under a stack carries everything above it.

If one block is tied back, the other has to break free at both its surfaces at once, so those two ceilings add. If nothing is tied back, slip could start at either surface, so find the force each one allows and take the smaller, like the cable that governs a junction. A cord between blocks just passes force along, so a line of tied blocks moves only when the pull reaches the sum of their ceilings.

A ladder on a rough floor fits here too. In Reactions of Bent Bars, Brackets, and Booms, a stop at the foot of a ladder against a smooth wall pushed with 105 lb, while the floor carried 200 lb. Take the stop away, and friction has to supply that 105 lb, so the least coefficient that works is:

μs,min⁡=FN=105200=0.525\mu_{s,\min} = \frac{F}{N} = \frac{105}{200} = 0.525

The Handbook has nothing on stacks or ladders. All of this is F≤μsNF \le \mu_s N and equilibrium.

Worked Example Pulling a block out from under another
1 of 4

What force PP just starts block B sliding out from under block A?

A 50 lb B 100 lb P μs = 0.30 μs = 0.20
Block A tied to a wall, on top of block B

A rope on a post

Take a few turns of rope around a post, and one hand can hold a load that would otherwise drag you across the dock. The rope does it by squeezing the post.

Look at one short piece of rope lying on the post. Tension TT pulls at each end of the piece, and because the rope curves, those two pulls press it into the post with a force of about T dθT\,d\theta. So friction on that piece can reach μT dθ\mu T\,d\theta, and that's how much the tension can change across it:

dT=μT dθdT = \mu T\,d\theta

More tension squeezes harder, which grips harder, so each bit of angle multiplies the tension by the same factor. That's the change that multiplies from Exponentials and Logarithms, smeared out continuously, so its base is ee. The Handbook's Belt Friction entry gives the result:

F1=F2eμθF_1 = F_2 e^{\mu\theta}

Here F1F_1 is the force applied in the direction of impending motion, F2F_2 is the force resisting it, μ\mu is the coefficient of static friction, and θ\theta is the total angle of contact in radians, so convert turns and degrees first. F1F_1 is always the larger one. It's the tight side, and slip impends toward it.

Fixed post 100 lb 257 lb 160 lb × 1.60 × 1.60 slip impends
Each quarter turn multiplies the tension by the same factor
With μ=0.30\mu = 0.30, a quarter turn is a factor of e0.30(π/2)=1.60e^{0.30(\pi/2)} = 1.60.

Because the wrap multiplies, doubling the angle squares the ratio: eμ(2θ)=(eμθ)2e^{\mu(2\theta)} = (e^{\mu\theta})^2.

Tension ratio with μ = 0.30
Wrapθ\theta (rad)F1/F2F_1/F_2
Half turn3.142.57
One turn6.286.59
Two turns12.5743.4
Four turns25.131,881

To find F1F_1, ask which way the rope would slide. When you're holding a load, the rope would run toward the load, so the load is F1F_1 and your hand is F2F_2. When you're raising it, the rope would run toward your hand, so your pull is F1F_1. Same post, same wrap, two very different numbers:

Phold=We−μθPraise=WeμθP_{\text{hold}} = W e^{-\mu\theta} \qquad P_{\text{raise}} = W e^{\mu\theta}
W P F1 (tight) F2 slip impends Holding P = W e−μθ W P F2 F1 (tight) slip impends Raising P = W eμθ
Holding and raising the same load
Checkpoint
1 of 2

A rope passes over a fixed drum and joins two hanging blocks, A and B. They're at rest, with block A just about to move up. Which part of the rope carries the larger tension?

A.
The part at block B
B.
The part at block A
C.
Neither, because one rope carries one tension
D.
It depends on the drum's radius

Now the numbers. Convert to radians yourself: μθ\mu\theta is a plain exponent, so the calculator's degree setting never touches it.

Worked Example An 800 lb load on a post
1 of 3

An 800 lb load hangs from a rope wrapped 1.5 turns around a fixed post, with μ=0.25\mu = 0.25. Find the smallest pull that holds it and the pull that starts raising it.

Working backward

When the load is the unknown, multiply by the factor. When the angle or the coefficient is unknown, it's stuck up in an exponent, and ln⁡\ln brings it down:

μθ=ln⁡F1F2\mu\theta = \ln\frac{F_1}{F_2}

To hold 1,000 lb with a 50 lb pull at μ=0.30\mu = 0.30, the ratio is 20, so θ=ln⁡20/0.30=9.99 rad\theta = \ln 20 / 0.30 = 9.99\ \text{rad}. Dividing by 2π2\pi gives 1.59 turns.

Checkpoint
1 of 3

You can hold a rope with 40 lb. It wraps 2 turns around a fixed post, with μ=0.30\mu = 0.30. What is the largest load you can hold?

lb

A belt on a pulley

A flat belt on a pulley obeys the same equation. Here θ\theta is the contact angle, the arc where the belt touches the pulley, and the equation caps how much tighter one side can be than the other. That difference is what turns the pulley. Each side pulls tangent to the pulley, with the radius as its arm, and their moments oppose each other, so the torque the belt delivers is:

M=(F1−F2) rM = (F_1 - F_2)\,r
r F1 (tight side) F2 (slack side) θ M
A belt's two sides pull against each other

The Handbook gives the tension ratio but not this line, which is just two moments. Torque is largest when the ratio is at its limit. With a slack side of 100 lb, μ=0.30\mu = 0.30, and half a turn of contact, the tight side can reach 256.6 lb. On a pulley of 6 in radius, that's M=(256.6−100)(0.5 ft)=78.3 lb⋅ftM = (256.6 - 100)(0.5\ \text{ft}) = 78.3\ \text{lb}\cdot\text{ft}.

Checkpoint
1 of 2

A flat belt's slack side carries 200 lb. The contact angle is 150°, and μ=0.35\mu = 0.35. What is the largest tension the tight side can have before the belt slips?

lb

Recap

  • Static friction is a reaction: it equals whatever equilibrium needs, up to μsN\mu_s N. Write F=μsNF = \mu_s N only at impending slip, and point friction against the slide that would happen without it.
  • On an incline, a block slides when the need beats the ceiling, which means θ>ϕ\theta > \phi, with tan⁡ϕ=μs\tan\phi = \mu_s, whatever it weighs.
  • Find NN from equilibrium every time, because angled forces change it. Starting a block up and keeping it from sliding down take different forces, because friction reverses.
  • Every sliding surface gets its own friction, and a lower surface carries everything above it.
  • Around a post or pulley, F1=F2eμθF_1 = F_2 e^{\mu\theta}, with θ\theta in radians and F1F_1 on the side slip impends toward. Doubling the wrap squares the ratio, and a belt's torque is (F1−F2)r(F_1 - F_2)r.