Forces and Resultants
Forces add like arrows, and components turn arrows into arithmetic.
Before this Lesson
- Vectors and Components · Mathematics and Statistics
- Triangle Trigonometry · Mathematics and Statistics
Three ropes are tied to one eyebolt, pulling with 300, 400, and 500 lb. How hard is the bolt being pulled? If all three pull the same way, 1,200 lb. Aim them just right, and the answer is zero: the bolt sits there and feels nothing. Same three numbers, wildly different answers, so the numbers can't be the whole story. You have to add the pulls with their directions, and this Lesson shows you how.
A force is an arrow
The Handbook's Statics section defines a force by its magnitude, its point of application, and its direction. An arrow carries all three, and extending it both ways gives the force's line of action.
Every force in this Lesson is concurrent, the Handbook's word for lines of action that meet at one point, like ropes on an eyebolt. Twisting waits for Moments and Couples. Here the forces share one job, pulling on that point, so a single force could do it alone. That force is the resultant, .
To find it, chain the arrows: put each tail at the previous tip, keeping every arrow's direction. The resultant runs from the first tail to the last tip. It's the walk from Vectors and Components, and either order lands on the same tip.
That settles the Hook. Chain the three pulls in a line, and is 1,200 lb. Bend the chain into a 3-4-5 triangle, and the last tip lands on the first tail, so is zero. A closed chain is what balance looks like, and Equilibrium of a Particle is built on it.
Opening the angle
Now fix the sizes of two forces and change only the angle between them, , measured with their tails together. Take 300 lb and 400 lb. At 0°, they pull together, and is 700 lb. Open the angle, and the chain starts folding back on itself, so shrinks. At 90°, it's the Pythagorean 500 lb. At 180°, the forces fight head-on, and is 100 lb, pointing the way the bigger one pulls.
So falls steadily as opens, from the sum of the two forces down to their difference, and it can never leave that range:
Two forces make a triangle
Chain two forces, and you've drawn a triangle whose third side is . The Handbook's Trigonometry section prints the two laws that solve it.
In a triangle, sides , , and face angles , , and . For more, see Triangle Trigonometry.
There's one catch. A problem gives you , the angle between the forces with their tails together. Slide to 's tip without turning it, and it still makes with 's line, extended. The triangle's corner is the rest of that straight line: the supplement, .
faces that corner, so the law of cosines reads:
Test it at : the corner is flat, its cosine is −1, and . Since , you'll also see this written with a plus sign and .
The law of sines gives the direction. faces , the angle between and :
Arcsine has the blind spot you've seen: it never returns more than 90°. But only a triangle's longest side can face an obtuse angle, so arcsine is safe unless is the longest side. Then run the law of cosines backward instead.
Components turn arrows into arithmetic
Triangles work for two forces. With four, you'd stack one triangle on the next. Here's the way out. Along one line, forces are just signed numbers: 30 lb right and 10 lb left make 20 lb right. So break each arrow into an x part and a y part. Each set adds like ordinary numbers, and neither sum can touch the other:
The Handbook prints this under Resultant (Two Dimensions), naming the resultant . This Lesson calls it to keep it apart from the forces going in.
This Topic's conventions: x to the right, y up, angles counterclockwise from the +x axis, and components carrying their signs. Measure that way, and the signs come out on their own. From here on, means this angle from +x:
So the first job is finding each , because the exam gives directions every other way. Walk around from +x: +y is at 90°, −x at 180°, −y at 270°. A force 25° left of +y is at 115°. A force 20° below −x is at 200°. When forces are given from their neighbors, keep a running total from the one given from an axis.
You can also skip the walk. The Handbook's Resolution of a Force writes every component with a cosine, and , each angle measured from that component's own axis. So measure an angle from the y-axis, and gets the cosine while gets the sine, each with the sign of where the arrow points.
A slope triangle is the force's direction drawn small
Plenty of problems never mention an angle. They draw a small right triangle beside the force, with its legs marked, say 4 and 3. That's the force's direction drawn small. The force and its components form a bigger triangle of the same shape, so each component is the force times the matching leg over the hypotenuse:
With 4 across and 3 up, the hypotenuse is 5, so a 100 lb force has and . There's no angle, no arctangent, and no calculator mode to get wrong.
The matching goes by direction, not by which number got printed first: the leg parallel to x goes with , so read a slope such as 3:1 off the drawing. Legs are lengths, so each component's sign comes from where the arrow points. The Handbook prints no slope triangle, but it prints the general equation, which you'll meet in three dimensions.
Arctangent finds the line, not the direction
Squaring wipes out the signs, so the magnitude doesn't care where points. The direction does. The Handbook prints under Resultant (Two Dimensions), with no word about quadrants. Back to the ropes, in degree mode:
That's down and to the right, but negative x and positive y mean points up and to the left. An arrow and its exact opposite have the same ratio, so arctangent can only find the line lies on, and it always answers between −90° and +90°. The signs say which way along that line.
The repair is short. If is negative, add 180°. If is positive and is negative, add 360°. For the ropes, . A calculator's rectangular-to-polar conversion handles the signs for you, though it may report any angle below the x-axis as negative. Add 360° to those.
Working backward to an unknown force
Sometimes the resultant is what you're told, and one of the forces is missing. The method doesn't change. Write and with the unknown inside them, then turn the sentence you were given into an equation. "Along the x-axis" means . "Along the y-axis" means . "A resultant of 500 lb" means . The unknown can be a magnitude or an angle.
A cable in space: the triangle grows a third leg
Off the flat page, a cable still pulls along a straight line, defined by two points. The coordinate differences , , and play the slope triangle's legs, and the line's length plays its hypotenuse. Same rule: the force times leg over hypotenuse.
Those fractions are the unit vector along the cable, so this is the force's size times its direction. The Handbook prints it under Resolution of a Force as , with . Mind that letter: there, is the line's length, not a resultant.
A cable can only pull, and it pulls whatever it's attached to toward its far end. So the tail goes at the point being pulled, the head at the far end, and the differences are head minus tail.
Direction angles: the same fractions again
Each of those fractions is also a cosine: , where is the line's angle from the +x axis, and and do the same for y and z. So , and likewise for y and z. That's the rest of Resolution of a Force, which writes these angles , , and .
Given components, the magnitude is . Each angle comes from , and a negative component gives an angle past 90°, with no fuss. Given two angles, the third comes from the identity under Direction Cosines of A, in the Handbook's Vectors section:
The square root leaves a ±, because squares can't tell up from down, so the problem has to say which: a force pointing upward, or an acute angle.
Several cables at one anchor
Nothing new is left, only bookkeeping. Each cable becomes three numbers. Stack them, add column by column, and take the square root of the sum of the squares. The Handbook's resultant stops at two dimensions, but its Vectors section adds one component at a time, and Length of Vector A finishes the job.