Equilibrium of a Particle

A hanging weight is a tug-of-war that nobody wins.

Before this Lesson

A 100 lb sign hangs from the middle of a wire strung between two posts. The wire slopes steeply up to each post, and each side carries about 58 lb. Now move the posts apart, flattening the wire. Somewhere along the way, a wire rated for 300 lb snaps. The sign didn't gain an ounce, and nothing else touched it. So where did the extra force come from? Two short equations settle it, and they run this whole Lesson.

Nothing moves, so everything cancels

In Forces and Resultants, you added the forces at a point to get a resultant. If that resultant weren't zero, the point would accelerate. A point sitting still has a resultant of zero, and that's all equilibrium is. The Handbook's Statics section prints it under Equilibrium Requirements as ΣFn=0\Sigma \mathbf{F}_n = 0. For forces in a plane, that means the x parts and the y parts each cancel on their own:

ΣFx=0ΣFy=0\Sigma F_x = 0 \qquad \Sigma F_y = 0

A particle is a point where all the forces meet: a ring, a knot, a joint. The Handbook's Concurrent Forces entry describes the same thing, lines of action that all meet at one point. Two equations can settle at most two unknowns, and the routine never changes: isolate, draw, sum to zero. Isolate the point, draw every force that touches it, and make each direction sum to zero.

Two kinds of member show up. A cable can only pull: push on a rope, and it goes slack. So its tension, TT, lies along the cable and pulls away from whatever it holds. A strut is a stiff bar. It also acts along its length, but it can push or pull: a strut that pushes is in compression, and one that pulls is in tension. The Handbook prints no rules for cables or struts, so these are yours to carry into the exam.

Now back to the wire. Isolate the point where the sign hangs. Both sides rise at the same angle θ\theta, so ΣFx=0\Sigma F_x = 0 makes their tensions equal. Each side hauls outward, the other hauls back, and all that effort does nothing for the sign. Only the vertical parts hold it up:

2Tsin⁡θ=W⇒T=W2sin⁡θ2T\sin\theta = W \quad\Rightarrow\quad T = \frac{W}{2\sin\theta}

At 60°, TT is 57.7 lb. At 30°, it's 100 lb, so each side carries the whole sign. At 5°, it's 574 lb. A flat wire leaves almost no vertical part, so the tension has to grow until that sliver can hold the sign. That's the extra force: the wire's two sides pulling against each other.

100 lb 60° T = 57.7 lb 100 lb 30° T = 100 lb 100 lb 5° T = 574 lb
The same sign on a wire that keeps flattening

When the two angles differ, so do the tensions, and the two sides no longer hold up equal parts of the weight. Here's a sign on two unequal cables, with its ring isolated beside it.

500 lb B C A 30° 45° Ring A, isolated A 30° 45° TAB TAC W = 500 lb
A sign on two cables, and its ring isolated
Worked Example A sign on two unequal cables
1 of 3

The 500 lb sign above hangs from ring A. Cable AB rises to the left at 30° above horizontal, and cable AC rises to the right at 45°. Find the tension in each cable.

The arrows close

Equilibrium has a picture, too. Chain the forces head to tail, as in the last Lesson. The resultant runs from the first tail to the last tip, so a zero resultant means the last tip lands on the first tail. The chain closes. Every arrow keeps its own direction, every tip meets the next tail, and the arrows chase each other around the loop. Three forces close into a triangle, the force triangle. More than three close into a polygon.

A triangle is a gift, because you can solve it without components.

Try it on the sign. Start with WW, 500 lb straight down. TACT_{AC} leaves WW's tip, and TABT_{AB} brings the chain back to the start. WW's line is vertical, so the two corners on it come from how far each cable leans from vertical: TACT_{AC} is 45° from vertical, and TABT_{AB}, at 30° above horizontal, is 60° from vertical. The third corner is what's left, 75°.

60° 45° 75° W = 500 lb TAC TAB
The sign's three forces, chained into a closed triangle

Each force faces one corner, so the Handbook's law of sines solves it:

TABsin⁡45∘=TACsin⁡60∘=500sin⁡75∘\frac{T_{AB}}{\sin 45^\circ} = \frac{T_{AC}}{\sin 60^\circ} = \frac{500}{\sin 75^\circ}

That gives TAB=366 lbT_{AB} = 366\ \text{lb} and TAC=448 lbT_{AC} = 448\ \text{lb}, the same as before, with no simultaneous equations. Notice that the 30° never went in directly. A corner is an angle between two force lines, so an angle given from horizontal has to become one from vertical here.

The triangle also explains the flattening wire. As it flattens, the WW side stays the same length while the other two sides stretch out to meet far away.

A smooth surface can only push straight out

A smooth surface has no grip, so it can't push along itself, and it can't pull. All it can do is push straight out, normal to the surface. That's the normal force, NN, which the Handbook names under Friction without spelling out its direction. Tilt a surface by θ\theta, and its normal tilts θ\theta from vertical. Friction itself waits for Static Friction.

A round roller is a particle in disguise: NN's line runs through its center, and so does the line of its weight. Hold one on a smooth incline with a cable running along the incline. The cable and the normal are perpendicular, so the force triangle has its right angle there, and WW is the hypotenuse:

T=Wsin⁡θN=Wcos⁡θT = W\sin\theta \qquad N = W\cos\theta
θ θ T N W Force triangle θ W T = W sin θ N = W cos θ
A roller held by a cable along the incline, and its force triangle

If you forget which one gets the sine, flatten the incline. At θ=0\theta = 0, the cable has nothing to do and the surface carries everything, so the part along the incline must be the sine. The Handbook prints neither formula, so the triangle is what you carry in.

Checkpoint
θ P W N
A roller held on a smooth plane by a horizontal force P

Which force diagram correctly shows this roller in equilibrium?

A.
W P N
B.
W P N
C.
W P N
D.
W P N

Look at that triangle. WW and PP meet at the right angle now, and NN is the hypotenuse. So N=Wcos⁡θN = W\cos\theta isn't a rule about inclines. It belongs to the case where the holding force runs along the surface. Draw the triangle for the case in front of you.

Worked Example A roller held by a horizontal force
1 of 3

A 400 N roller rests on a smooth 30° incline, held by a horizontal force PP. Find PP and the normal force.

More forces, same two equations

With four or more forces, the polygon still closes, but there's no law of sines for it, so go back to components. The two equations can settle any two unknowns: two magnitudes, or one force's magnitude and direction.

If one force is missing entirely, you've met it already. It has to cancel the resultant of the others, so it's that resultant turned exactly around. If two magnitudes are missing and one of those forces lies along an axis, write the other axis's equation first. It can't see that force, so it has just one unknown. And if three forces have known sizes and unknown directions, you already have the triangle's three sides, so run the law of cosines backward for a corner.

Worked Example The fourth force on a ring
1 of 3

What single added force holds this ring in equilibrium? Give its magnitude and its direction from the +x axis.

500 lb 300 lb 200 lb 30° 45° x y
Three known forces on a ring

Which cable gives out first?

Cables have limits, and the exam likes to ask for the largest weight a junction can carry. One fact makes this easy: the geometry sets each cable's share, so double the weight and every tension doubles. Each tension is a fixed multiple of WW, so each cable's limit gives its own largest WW. The junction has to satisfy all of them at once, and the smallest one wins. Comparing the allowable tensions alone tells you nothing, because they ignore the shares.

Worked Example The largest sign two cables can hold
1 of 2

Keep the same two cables, AB at 30° and AC at 45°. AB's allowable tension is 900 lb, and AC's is 1,000 lb. What is the largest weight they can hold?

An ideal pulley only turns the cable

An ideal pulley is a weightless wheel on a frictionless axle. If one side of its cable pulled harder than the other, the wheel would spin, and at rest it doesn't. So the pulley turns the cable without changing its tension, and one cable carries one tension from end to end, however many pulleys it wraps. The Handbook says nothing about pulleys or block and tackle, so all of this comes from equilibrium.

To find the pull on a hoist, isolate the moving block: draw a box around it and count. Every cable segment holding the block pulls up with TT. With nn segments holding it, ΣFy=0\Sigma F_y = 0 gives:

nT=W⇒T=WnnT = W \quad\Rightarrow\quad T = \frac{W}{n}

The pull at the free end is that same TT. Count only the segments that hold the moving block. A last run from a fixed pulley down to your hand doesn't touch it, so that run just redirects your pull.

P T W n = 1 P = W P T T W n = 2 P = W/2 P T T T T W n = 4 P = W/4
Counting the segments that hold the moving piece
Checkpoint
1 of 2
P 900 N
A 900 N load on a hoist

What pull PP holds the load at rest?

N

The axle feels both runs

The pulley is in equilibrium too. The cable pulls on it twice, with TT along each run, pointing away from the pulley, and the axle has to balance those two pulls. So the force on the axle is their resultant. Let β\beta be the angle between the runs. Each pull has a part Tcos⁡(β/2)T\cos(\beta/2) along the line halfway between them, and their sideways parts cancel:

R=2Tcos⁡β2R = 2T\cos\frac{\beta}{2}

RR lies along the line halfway between the two runs. Test it. With the runs parallel, β=0\beta = 0, and R=2TR = 2T. At 90°, R=1.41TR = 1.41T. At 180°, the cable runs straight past, and the pulley feels nothing.

T T R β Head to tail T T R β/2 β/2
Two equal cable pulls, and the force they put on the axle
Checkpoint

A cable holding a 500 lb weight runs straight up to an ideal pulley, passes over it, and leaves to the right at 20° above horizontal. What is the magnitude of the force on the axle?

A.
574 lb
B.
1,000 lb
C.
940 lb
D.
500 lb

Two blocks, one cable

Tie block A, on a smooth incline, to a hanging block B, with the cable running parallel to the incline and over an ideal pulley at the top. One cable, one TT. Isolate each block. The hanging block gives T=WBT = W_B. The block on the incline gives T=WAsin⁡θT = W_A\sin\theta, as the cable did for the roller. Set them equal:

WB=WAsin⁡θW_B = W_A\sin\theta

The incline carries the WAcos⁡θW_A\cos\theta part, so block B only has to balance the part along the slope. That's how a small weight can hold a big block on a gentle slope.

θ A T N WA WA cos θ WA sin θ B T WB
Two blocks tied over an ideal pulley
Checkpoint
1 of 2

A 60 kg block on a smooth 35° incline is tied to a hanging block by a cable parallel to the incline, over an ideal pulley. What hanging mass keeps them at rest?

kg

Recap

  • Isolate, draw, sum to zero: ΣFx=0\Sigma F_x = 0 and ΣFy=0\Sigma F_y = 0, at most two unknowns. A cable pulls away from what it holds, and a strut pushes or pulls along its length.
  • The forces chain into a closed polygon. Three make a force triangle, which the law of sines solves using corners between force lines.
  • A smooth surface pushes normal to itself. T=Wsin⁡θT = W\sin\theta and N=Wcos⁡θN = W\cos\theta hold only when the other force runs along the incline.
  • For a largest load, find the weight each cable's limit allows, and take the smallest.
  • One cable, one tension. On a hoist, nT=WnT = W, counting segments that hold the moving block. On an axle, R=2Tcos⁡(β/2)R = 2T\cos(\beta/2). Over a pulley on an incline, WB=WAsin⁡θW_B = W_A\sin\theta.