Pump Head and Power

A pump buys head with power, and efficiency sets the price.

Before this Lesson

A town's pump station draws 1,000 gallons a minute from a river and sends it up to a storage tank on a hill, where the water surface stands 150 ft above the river's. Picture doing that by hand. A 5-gallon bucket of water weighs about 42 lb, so 1,000 gpm is more than three full buckets carried up a 15-story building every second, all day and all night.

A pump does it with an electric motor, and the town pays the electric bill. By the end of this Lesson, you'll know how much power that motor draws and what a day of its work costs.

Weight per second, times height

Lifting a weight WW through a height hh takes work WhWh. A pump does that without stopping: every second, a fresh batch of water passes through it, and the pump raises it through the head hph_p. The weight passing each second is the specific weight times the flow, γQ\gamma Q. Work per second is power, as in Power and Efficiency, so the power that ends up in the water is

W˙water=Qγhp\dot W_{\text{water}} = Q\gamma h_p

The Handbook's Centrifugal Pump Characteristics section calls this the fluid power. Its head is the same hph_p as in The Energy Equation, and it writes power as W˙\dot W, which keeps PP free for pressure.

In U.S. units, QQ in cfs times 62.4 lb/ft³ times hph_p in feet gives ft-lb/s, and 550 of those make a horsepower. The Hook's 1,000 gpm is 2.228 cfs, so lifting it 150 ft takes

W˙water=2.228(62.4)(150)=20,850 ft-lb/s=20,850550=37.9 hp\dot W_{\text{water}} = 2.228(62.4)(150) = 20{,}850\ \text{ft-lb/s} = \frac{20{,}850}{550} = 37.9\ \text{hp}

SI is kinder. With γ=9.81 kN/m3\gamma = 9.81\ \text{kN/m}^3, QQ in m³/s, and hph_p in meters, the product comes out in kN·m/s, which is kilowatts, with no conversion at all.

No pump hands all of its shaft's power to the water. Some churns into eddies in the casing, some drives water that leaks back around the impeller, and some goes into bearing friction, and it all ends up as heat. So the shaft must supply more than the water receives, and the ratio is the pump efficiency ηp\eta_p:

W˙brake=W˙waterηp\dot W_{\text{brake}} = \frac{\dot W_{\text{water}}}{\eta_p}

This is the Handbook's pump (brake) power, the power at the pump's shaft. At 75% efficiency, the Hook's pump needs 37.9/0.75=50.5 hp37.9/0.75 = 50.5\ \text{hp} there. Dividing by a number below 1 always makes it bigger, and that's your check: the shaft can't deliver less than the water gets.

Checkpoint
1 of 2

A pump delivers 1,200 gpm against a head of 85 ft and is 78% efficient. What is its brake power, in hp?

hp

Total dynamic head

So far the head was simply the lift. The energy equation says what a pump really has to supply. Put point 1 on the surface of the water the pump draws from, a sump or wet well, and point 2 on the surface of the tank it fills. Their pressure and velocity heads drop out, as in The Energy Equation:

hp=(z2−z1)+hfh_p = (z_2 - z_1) + h_f

The first term is the static head, the lift from one water surface to the other, there whether or not any water moves. The second is every loss the moving water pays: pipe friction, which a problem states or has you find by Hazen-Williams or Darcy-Weisbach, plus a minor loss C v2/2gC\,v^2/2g at each entrance, bend, valve, and exit, with CC the fitting's loss coefficient. Those losses exist only while water flows, which is why the sum is called the total dynamic head (TDH). It's the hph_p of the power equation. The Handbook defines neither term, and "total dynamic head" appears there only as an axis label on its sample pump curve.

flow pump sump water surface tank water surface static head
Static head runs from water surface to water surface

Nothing else in a pump station's data enters the static head. Slide the pump up or down its suction line, and the water still starts at the sump's surface and ends at the tank's. (The pump's height does decide whether its suction side can boil into vapor, a question this Lesson leaves out.) The floors of the sump and tank don't count, and neither does where the pipe enters the tank: water entering below the surface still has to push against all the water above it. Only a pipe that ends above the water and spills freely has to lift it to the outlet instead.

Checkpoint

A pump station's drawings give these elevations: ground at the station, 210.0 ft; wet-well floor, 188.5 ft; suction inlet, 190.0 ft; wet-well water surface, 194.0 ft; pump centerline, 199.0 ft; tank floor, 318.0 ft; discharge pipe's entry into the tank, 320.0 ft; tank water surface, 342.5 ft. What is the static head?

ft

On a pump that's already running, there's a shortcut: read the head off its gauges. Write the energy equation from the suction flange, s, to the discharge flange, d, with nothing but the pump between them:

hp=Pd−Psγ+(zd−zs)+vd2−vs22gh_p = \frac{P_d - P_s}{\gamma} + (z_d - z_s) + \frac{v_d^2 - v_s^2}{2g}

With the gauges at one height on pipes of one size, as problems usually arrange, the last two terms vanish, and the pump head is the jump in pressure head across the pump, at 2.31 ft of water per psi.

One sign needs care. A pump that sits above its sump has to pull water up its suction pipe, so the suction gauge reads below atmospheric, a vacuum. A vacuum is a negative gauge pressure, and subtracting a negative adds. A pump that takes water at a 4 psi vacuum and delivers it at 50 psi raises its pressure by 54 psi, which is 54(144)/62.4=124.6 ft54(144)/62.4 = 124.6\ \text{ft} of head.

Ps/γ = −9.2 ft Pd/γ = 115.4 ft hp = 124.6 ft pump suction gauge −4 psi (vacuum) discharge gauge 50 psi
The head a pump adds, read from its gauges
Worked Example TDH, then the brake power
1 of 3

A pump lifts 1,500 gpm through a 10 in. line from a wet well with its water surface at elevation 102 ft to a reservoir with its surface at 230 ft. Pipe friction takes 18 ft, and the entrance, fittings, and exit have loss coefficients that add up to ∑C=6.5\sum C = 6.5. The pump is 80% efficient. Find the total dynamic head and the brake power.

From the wire to the water

The pump's shaft is turned by an electric motor, and the motor has losses of its own: its windings and bearings warm up. So the power it draws from the wire is larger again, by its efficiency ηm\eta_m:

W˙input=W˙brakeηm=W˙waterηp ηm\dot W_{\text{input}} = \frac{\dot W_{\text{brake}}}{\eta_m} = \frac{\dot W_{\text{water}}}{\eta_p\,\eta_m}

This is what the Handbook calls the purchased power, and it's what the utility pays for. Each machine divides once, and as in Power and Efficiency, efficiencies in a chain multiply. The Handbook's Pump Power Equation packs the whole chain into one line, with a total efficiency ηt=ηpump×ηmotor\eta_t = \eta_{\text{pump}} \times \eta_{\text{motor}}:

W˙=Qγhηt\dot W = \frac{Q\gamma h}{\eta_t}

Use it with ηt\eta_t for the motor input, or with the pump efficiency alone for the brake power.

motor ηm = 0.90 pump ηp = 0.80 motor input 83.3 kW brake power 75.0 kW water power 60.0 kW motor losses 8.3 kW pump losses 15.0 kW ÷ 0.80 ÷ 0.90 ηt = 0.90 × 0.80 = 0.72
Each machine passes on a fraction of what it receives
Working back from 60 kW of water power, divide by 0.80 for the pump's shaft and by 0.90 again for the wire.

The electric bill charges for energy, power times time, in kilowatt-hours: the motor input in kW, times the hours it runs, times the rate per kWh. Now finish the Hook. Say its pipeline loses 20 ft at 1,000 gpm, so the TDH is 170 ft and the water power is 43.0 hp. With a 75% pump and a 90% motor:

W˙input=43.00.75(0.90)=63.7 hp=63.7(0.746)=47.5 kW\dot W_{\text{input}} = \frac{43.0}{0.75(0.90)} = 63.7\ \text{hp} = 63.7(0.746) = 47.5\ \text{kW}

A day of that is 47.5(24)=1,140 kWh47.5(24) = 1{,}140\ \text{kWh}, and at $0.12 per kWh, the town pays about $137 a day to lift its water.

Checkpoint
1 of 2

A pump delivers 0.18 m³/s against a total dynamic head of 32 m. The pump is 80% efficient and its motor 92%. What power does the motor draw, in kW?

kW

Working backward

The same equation runs backward. A pump test measures the flow with a meter, the head with gauges, and the power with an electric meter or a shaft dynamometer. The efficiency is then what the water got, divided by what went in:

η=W˙waterW˙measured\eta = \frac{\dot W_{\text{water}}}{\dot W_{\text{measured}}}

Measure the electric input, and this ratio is ηt\eta_t; measure the shaft power, and it's ηp\eta_p alone. If the efficiency is known instead, solve the power equation for the flow a given power can move, or the head it can add:

Q=η W˙γhphp=η W˙γQQ = \frac{\eta\,\dot W}{\gamma h_p} \qquad\qquad h_p = \frac{\eta\,\dot W}{\gamma Q}

Here η\eta multiplies, and that's no contradiction. The power going in, times the efficiency, is the share that reaches the water, and only that share lifts it.

Checkpoint
1 of 3

In a field test, a pump delivers 2.2 cfs while its gauges show a head of 120 ft, and a dynamometer on its shaft reads 38 hp. What is the pump's efficiency, in percent?

%

A day's water in fewer hours

Many problems state a job rather than a flow: a town uses 2 million gallons a day, and its pumps must keep up. Pumps rarely run around the clock. A utility may run them only at night, when power is cheaper, or only during one shift. The day's volume is fixed, so fewer hours means a faster rate:

Q=VtrunQ = \frac{V}{t_{\text{run}}}

Pump 2 MG over 24 hours, and the rate is 2,000,000/1,440=1,389 gpm2{,}000{,}000/1{,}440 = 1{,}389\ \text{gpm}. Squeeze it into 8 hours, and the rate is 4,167 gpm, three times as fast, so at the same head it takes three times the power. Divide by the hours the pump actually runs, not the 24 in a day, and the power follows as before.

Checkpoint

A town must pump 1.5 MG each day against a total dynamic head of 140 ft, and its pumps run only 10 hours a day. The pump is 78% efficient. What brake power does it need, in hp?

hp

Static head stays put, friction doesn't

Pumping faster changes the head, too. Look again at the two parts of the TDH. The static head is a difference in elevation, so it doesn't care how fast the water moves: at a trickle or a flood, the lift is the same. The losses are different. Each grows with the velocity head, and the velocity grows with the flow. Darcy-Weisbach, hf=f(L/D) v2/2gh_f = f(L/D)\,v^2/2g, goes as Q2Q^2 for a steady ff, and Hazen-Williams as Q1.852Q^{1.852}, close enough that problems usually say "roughly the square of the flow." Double the flow, and the friction head about quadruples, while the static head doesn't move.

0 500 1,000 1,500 2,000 0 50 100 150 200 flow, Q (gpm) head (ft) static head TDH 25 ft 100 ft friction and minor losses
The head a pipeline needs at each flow

Plotted against flow, the TDH is a flat floor of static head with the losses rising above it in a parabola. So the TDH isn't proportional to the flow, and the power, QγhpQ\gamma h_p, climbs faster than the flow does, because the head climbs with it. To find the head at a new flow, scale only the losses:

hp,2=(z2−z1)+hf,1(Q2Q1)2h_{p,2} = (z_2 - z_1) + h_{f,1}\left(\frac{Q_2}{Q_1}\right)^2

Pump Curves and Operating Points calls this curve the system curve and finds where a pump will run on it.

Checkpoint
1 of 2

At 2,000 gpm, a pump station's total dynamic head is 180 ft, of which 130 ft is static head. Taking the losses to grow with the square of the flow, what is the total dynamic head at 2,500 gpm?

ft

Recap

  • Water power is the weight of water lifted each second times the head, W˙water=Qγhp\dot W_{\text{water}} = Q\gamma h_p: ft-lb/s from cfs and feet, at 550 per hp, or kW straight from m³/s and meters.
  • The total dynamic head is the static head, from water surface to water surface, plus every loss, or the pressure jump across the pump's gauges, with a suction vacuum counted as negative.
  • Efficiencies divide on the way to the wire: W˙brake=W˙water/ηp\dot W_{\text{brake}} = \dot W_{\text{water}}/\eta_p and W˙input=W˙water/(ηp ηm)\dot W_{\text{input}} = \dot W_{\text{water}}/(\eta_p\,\eta_m). The energy cost is the input in kW times hours times the rate.
  • Run backward, the efficiency is the water power over the measured power, and ηW˙=Qγhp\eta\dot W = Q\gamma h_p gives QQ or hph_p. A daily volume needs Q=V/trunQ = V/t_{\text{run}}, over the hours the pump runs.
  • The static head stays the same at every flow, while the losses grow with roughly the square of the flow.