Mass Moment of Inertia

Mass far from the axis resists spinning more than mass near it.

Grip a sledgehammer at the very end of its handle and try to whip it around. It fights you. Now slide your hand up until it's right under the head, and the same hammer swings like a stick. Its mass never changed. All you changed is how far that mass sits from your hand.

This Lesson puts a number on that, then uses it on flywheels, drums, and swinging rods.

Distance counts twice, again

Take a wheel on a fixed axle, speeding up with angular acceleration α\alpha, and watch one small bit of its mass, dmdm, a distance rr from the axle. From Rotation and Circular Motion, that bit accelerates along its path at rαr\alpha, so something has to push it with a force dF=dm (rα)dF = dm\,(r\alpha). That force acts on an arm of rr, so the moment it takes about the axle is r dF=r2α dmr\,dF = r^2\alpha\,dm.

Now put an equal bit twice as far out. It has to accelerate twice as hard, so it takes twice the force, and that force works on twice the arm. That's four times the moment. Distance counts twice, as it did for the plank in Moment of Inertia of Areas, though for a different reason.

axle α dF dm 2 dF dm r 2r
A bit twice as far out takes twice the force on twice the arm

Add up every bit. A rigid body has one α\alpha, so it comes outside the integral:

ΣM=(∫r2 dm)α=Iα\Sigma M = \left(\int r^2\,dm\right)\alpha = I\alpha

The integral is the mass moment of inertia, I=∫r2 dmI = \int r^2\,dm, and ΣM=Iα\Sigma M = I\alpha is Newton's second law for rotation: moment for force, α\alpha for aa, and II for mm. The Handbook prints the integral under Mass Moment of Inertia, and the law under Rigid Body Rotation About a Fixed Axis, as ΣMq=Iqα\Sigma M_q = I_q\alpha, with qq naming the axis.

Unlike plain mass, II belongs to a body and an axis together, which is the hammer: move your hand, and II changes. Its units are mass times length squared, slug-ft² or kg·m², though the Handbook doesn't print them.

The shape table does the integrating

You'll rarely do that integral. The last pages of the Handbook's Dynamics chapter hold a table with a Mass Moment of Inertia column, already integrated for uniform bodies. It writes MM for mass, where the rest of the chapter writes mm. Its first rows have sketches but no names, and its axis subscripts change meaning from row to row, so here are the rows you'll use most, with the axes in words.

Slender rod mL2/3 mL2/12 c L Thin ring mR2 R 3mR2/2 Solid cylinder mR2/2 R Solid sphere 2mR2/5 R
Four bodies from the shape table, with their axes

Adapted from the FE Reference Handbook, Dynamics, mass moment of inertia table

Mass moments of inertia of uniform bodies
BodyAxisII
Slender rodCenter, square to the rodmL2/12mL^2/12
Slender rodEnd, square to the rodmL2/3mL^2/3
Thin ringCenter, square to the ringmR2mR^2
Thin ringTangent, in the ring's plane3mR2/23mR^2/2
Thin ringRim, square to the ring2mR22mR^2
Solid cylinderIts long axismR2/2mR^2/2
Thin diskCenter, square to the diskmR2/2mR^2/2
Solid sphereA diameter2mR2/52mR^2/5
Thin plate, a by bCenter, parallel to side amb2/12mb^2/12

Adapted from the FE Reference Handbook, Dynamics, mass moment of inertia table

The mass comes first, and a problem gives it one of two ways. From a weight, m=W/gm = W/g, as in Newton's Second Law. From a density, mass is density times volume, and the table's Mass & Centroid column has that built in, such as M=πR2ρhM = \pi R^2\rho h for a cylinder.

Worked Example A rod about its end
1 of 3

A uniform slender rod weighs 12 lb and is 6 ft long. Find its mass moment of inertia about an axis through one end, square to the rod.

Moving the axis

For an axis the table doesn't list, use the parallel-axis theorem from Moment of Inertia of Areas, with mass in place of area. The proof is the same too: square each bit's distance to the new axis, and the cross term vanishes because the mass balances about its own center:

I=Ic+md2I = I_c + md^2

IcI_c is about the parallel axis through the mass center, and dd is the distance between the axes. The Handbook's Parallel-Axis Theorem calls the left side InewI_{\text{new}}.

c Ic I d L
A rod and an axis offset from its mass center

Test it on a rod, whose end is L/2L/2 from its center: mL2/12+m(L/2)2=mL2/3mL^2/12 + m(L/2)^2 = mL^2/3, the table's end row. The same two rules carry over from areas:

  • md2md^2 can't be negative, so the axis through the mass center has the least II of all parallel axes.
  • One end of every transfer has to be the mass center. So mL2/3mL^2/3 gets no md2md^2 added for reaching the end, because it already holds it. And to go between two off-center axes, come down to IcI_c first, then go back up.
Checkpoint
1 of 3

A uniform 16.1 lb rod 4 ft long turns about an axis square to the rod, 1 ft from one end. What is its mass moment of inertia about that axis?

slug-ft²

Bodies built from parts

II is a sum over the mass, so the parts of a body add, as long as all of them are about the same axis. For a pendulum, that's the pivot. Each part contributes its own IcI_c plus md2md^2, with dd running from the pivot to that part's own mass center.

pivot c c L R drod = L/2 ddisk = L + R
A rod and disk pendulum, measured from the pivot

Watch the disk. Its center sits past the end of the rod, so its dd is L+RL + R, not LL.

Worked Example A rod and disk pendulum
1 of 3

A pendulum is a uniform 6.44 lb rod 3 ft long, pivoted at its top end, with a 9.66 lb uniform disk of radius 0.5 ft fixed to its lower end. Both swing in the plane of the disk. Find II about the pivot.

Radius of gyration

A real flywheel, with spokes and a heavy rim, isn't in the table. So its maker gives you its weight and one length, the radius of gyration kk. Picture gathering all of the body's mass into a thin ring about the axis. kk is the radius of the ring that would have the same II:

I=mk2k=ImI = mk^2 \qquad\qquad k = \sqrt{\frac{I}{m}}

The Handbook's Mass Radius of Gyration writes the square-root form with rmr_m for kk, and the last column of its shape table lists the square of it for each row. For a thin ring about its center, k=Rk = R. A solid disk of the same mass and radius has k=R/2=0.707Rk = R/\sqrt{2} = 0.707R, because some of its mass sits close in.

Thin ring R k = R Solid disk R k = 0.707R same mass m, same radius R, axis through the center
Where each body's radius of gyration falls
Checkpoint
1 of 3

A 50 kg rotor has I=3.2 kg⋅m2I = 3.2\ \text{kg}\cdot\text{m}^2 about its shaft. What is its radius of gyration?

m

Which I, and which is larger?

The area moment of inertia and the mass moment of inertia share a letter, and each counts by distance squared, but they answer different questions. The Handbook prints no warning, and it uses IxI_x for both, so go by the units and by whether a mass is involved.

Two quantities that share the letter I
PropertyArea momentMass moment
DefinitionIx=∫y2 dAI_x = \int y^2\,dAI=∫r2 dmI = \int r^2\,dm
Unitsin⁴, mm⁴slug-ft², kg·m²
Resistsbending of a sectionangular acceleration
Handbook chapterStaticsDynamics

Ranking bodies by mass moment comes down to one question: where does the mass sit? Push it away from the axis, and II climbs. Move the axis away from the mass center, and II climbs too, by md2md^2.

Checkpoint
1 of 4

A spec sheet lists a rotor at I=24 slug-ft2I = 24\ \text{slug-ft}^2 and a beam at I=340 in4I = 340\ \text{in}^4. Which statements are true?

A.
The 340 in⁴ gives the beam's angular acceleration about a pin.
B.
The 24 slug-ft² sets how fast a given moment spins up the rotor.
C.
Multiplying 24 slug-ft² by 12⁴ puts it in the same units as 340 in⁴.
D.
The 340 in⁴ describes how the beam's section resists bending.

A flywheel: the moment sets the acceleration

Now put ΣM=Iα\Sigma M = I\alpha to work. A flywheel coasts on a fixed axle, and a brake presses on its rim. On its free-body diagram, the weight, the brake's press, and the axle's push all act through the axle, so they have no arm. Only the friction force FF has one, the rim radius rr, and that makes the equation short: Fr=IαFr = I\alpha. A motor's torque goes straight in the same way. The Handbook's equivalent for a shaft is ΣT=Iα\Sigma T = I\alpha, with TT for torque.

r F W axle force N ω α
A braked flywheel, drawn free

A constant moment gives a constant α\alpha, and that's the end of the new physics. From there, it's ω=ω0+αt\omega = \omega_0 + \alpha t and the other equations from Rotation and Circular Motion, with rpm converted by 2π/602\pi/60.

Worked Example Braking a flywheel
1 of 3

A 500 lb flywheel with a radius of gyration of 1.2 ft coasts at 1,200 rpm. A brake on its rim, 1.5 ft from the axle, applies a friction force of 30 lb. Find the angular deceleration and the time to stop.

A drum and a falling weight

Wrap a cord around a drum on a fixed axle, hang a weight on it, and let go. This is the two-body cord problem from Newton's Second Law, except that the drum is a pulley with mass, so it counts as a body. Draw two free-body diagrams, with TT as the cord tension in both.

The setup r W α a Drum r Wdrum axle force T α Weight T W a
A drum and its hanging weight, each drawn free

The cord moves with the rim, which ties the two motions together:

drum:Tr=Iαweight:W−T=Wgacord:a=rα\begin{aligned} \text{drum:}\quad Tr &= I\alpha \\[4pt] \text{weight:}\quad W - T &= \frac{W}{g}a \\[4pt] \text{cord:}\quad a &= r\alpha \end{aligned}

That's three equations for TT, aa, and α\alpha. Eliminate TT and α\alpha:

a=WW/g+I/r2a = \frac{W}{W/g + I/r^2}

Read that like the sentence from Newton's Second Law: the driving force over everything it has to accelerate. The drum acts like extra mass I/r2I/r^2 riding on the cord. The Handbook prints none of this, only the pieces to build it from.

The problem can also run backward. If the weight falls from rest through a measured distance in a measured time, then Δs=12at2\Delta s = \tfrac12 at^2 gives aa, the cord gives α\alpha, the weight's equation gives TT, and the drum's equation gives II.

Worked Example A weight on a drum
1 of 4

A 64.4 lb weight hangs from a cord wrapped around a drum with r=1 ftr = 1\ \text{ft} and I=6 slug-ft2I = 6\ \text{slug-ft}^2. Find the weight's acceleration, the drum's angular acceleration, and the cord tension.

A rod let go

Hold a uniform rod level, pinned at one end, and let go of the other. At that first instant nothing is moving yet, so ω=0\omega = 0. Two questions: what's α\alpha, and how hard does the pin push?

Rpin c W α L/2 L
A rod pinned at one end, at the instant of release

The pin's push is unknown, so take moments about the pin, and it drops out. The weight acts at the mass center, on an arm of L/2L/2, not LL. And II is the table's end row:

mgL2=mL23α⇒α=3g2Lmg\frac{L}{2} = \frac{mL^2}{3}\alpha \quad\Rightarrow\quad \alpha = \frac{3g}{2L}

The mass cancels. A rod's mass center sits L/2L/2 from the pin, so it accelerates down at (L/2)α=3g/4(L/2)\alpha = 3g/4, slower than free fall. The free end, at Lα=3g/2L\alpha = 3g/2, goes faster than free fall: set a coin on it, let go, and the rod drops out from under the coin.

Now ΣF=ma\Sigma F = ma, using the mass center's acceleration, gives the pin:

W−Rpin=Wg(3g4)⇒Rpin=W4W - R_{\text{pin}} = \frac{W}{g}\left(\frac{3g}{4}\right) \quad\Rightarrow\quad R_{\text{pin}} = \frac{W}{4}

Before release, the pin carried half the weight. An instant later, it carries a quarter. With ω=0\omega = 0, there's no normal acceleration, so the pin has no sideways force to supply.

ΣM=Iα\Sigma M = I\alpha holds only about a fixed axis or the mass center, which the Handbook writes ΣMc=Icα\Sigma M_c = I_c\alpha. About any other point, such as the free end, it picks up an extra term.

Worked Example The 12 lb rod, let go
1 of 3

The 12 lb, 6 ft rod from earlier is pinned at one end and released from rest in a horizontal position. Find its initial angular acceleration and the pin reaction.

Recap

  • Each bit of mass counts by its distance squared: I=∫r2 dmI = \int r^2\,dm, in slug-ft² or kg·m², not length to the fourth.
  • Find the mass as W/gW/g or density times volume, then read the table row for your axis.
  • I=Ic+md2I = I_c + md^2, with the mass center at one end of every transfer. Parts add about one axis, each with dd to its own mass center.
  • I=mk2I = mk^2. The mass-center axis has the least II.
  • ΣM=Iα\Sigma M = I\alpha about a fixed axis or the mass center. A drum and its weight share TT, tied by a=rαa = r\alpha. A rod let go has an arm of L/2L/2, α=3g/(2L)\alpha = 3g/(2L), and a pin reaction of W/4W/4.