Rotation and Circular Motion

Moving in a circle at constant speed is still accelerating, toward the center.

Before this Lesson

A flywheel 2 ft across spins at a steady 1,800 rpm. Its speed isn't changing at all. Yet a 1 oz bolt on its rim is accelerating at about 1,100 times gg, and whatever holds that bolt on has to pull inward with about 69 lb.

You'll get both numbers from a few lines of arithmetic. The first step is counting the wheel's rotation in a unit the math can use.

Rotation is translation with new letters

A wheel on a fixed axle doesn't go anywhere, so what changes is an angle. Paint a line from the hub to the rim and track its angle θ\theta. How fast that angle changes is the angular velocity, ω=dθ/dt\omega = d\theta/dt, and how fast ω\omega changes is the angular acceleration, α=dω/dt\alpha = d\omega/dt.

That's the chain from Position, Velocity, and Acceleration, with θ\theta, ω\omega, and α\alpha standing in for ss, vv, and aa. So when α\alpha is constant, the equations from Constant-Acceleration Motion carry over letter for letter, and the same habit picks among them.

The constant-acceleration equations, straight and turning
Leaves outStraight lineRotation
Displacementv=v0+atv = v_0 + atω=ω0+αt\omega = \omega_0 + \alpha t
Final speedΔs=v0t+12at2\Delta s = v_0 t + \tfrac12 at^2Δθ=ω0t+12αt2\Delta\theta = \omega_0 t + \tfrac12 \alpha t^2
AccelerationΔs=12(v0+v)t\Delta s = \tfrac12 (v_0 + v)tΔθ=12(ω0+ω)t\Delta\theta = \tfrac12 (\omega_0 + \omega)t
Timev2=v02+2a Δsv^2 = v_0^2 + 2a\,\Delta sω2=ω02+2α Δθ\omega^2 = \omega_0^2 + 2\alpha\,\Delta\theta

Rotation column adapted from the FE Reference Handbook, Rigid Body Rotation About a Fixed Axis

The Handbook prints all but the average-speed form, writing α0\alpha_0 for α\alpha and θ−θ0\theta - \theta_0 for Δθ\Delta\theta.

The catch is the unit. Machines run in rpm and counters count revolutions, but everything later in this Lesson needs radians. The Handbook's Units and Conversion Factors table has both conversions:

ω (rad/s)=rpm×2π60θ (rad)=rev×2π\begin{aligned} \omega\ (\text{rad/s}) &= \text{rpm} \times \frac{2\pi}{60} \\[4pt] \theta\ (\text{rad}) &= \text{rev} \times 2\pi \end{aligned}

So the flywheel's 1,800 rpm is 1,800(2π/60)=188.5 rad/s1{,}800(2\pi/60) = 188.5\ \text{rad/s}.

Worked Example A flywheel slowing down
1 of 3

A flywheel slows uniformly from 1,800 rpm to 600 rpm in 20 s. Find its angular acceleration in rad/s² and the revolutions it turns during that time.

One angle, many speeds

Now look at the points on the wheel. It's rigid, so the painted line stays straight, and every point on it sweeps the same angle in the same time. So θ\theta, ω\omega, and α\alpha belong to the whole body. What the points don't share is distance: in one turn, a point near the hub walks a small circle while a rim point walks a big one.

Arc length is s=rθs = r\theta. Differentiate it with rr fixed, and out come the speed and the tangential acceleration, the part of the acceleration along the path:

v=rωat=rαv = r\omega \qquad\qquad a_t = r\alpha

The Handbook's Plane Circular Motion section prints these as vθv_\theta and aθa_\theta, calling them transverse, which on a circle means tangential.

θ sA sB A (at r) B (at 2r) v = rω v = 2rω ω O
The same angle takes the outer point twice as far

For the bolt, v=(1 ft)(188.5 rad/s)=188.5 ft/sv = (1\ \text{ft})(188.5\ \text{rad/s}) = 188.5\ \text{ft/s}, about 129 mph. (A radian is a length over a length, so it drops out.) Leave ω\omega in rpm and you'd get 1,800 ft/s, well past the speed of sound, for a bolt on a flywheel.

A belt on a pulley, or a cable wound on a drum, moves with the rim as long as it doesn't slip. So it has the rim's rωr\omega and rαr\alpha, and a load on the cable goes along.

r load ω α v = rω a = rα
The cable moves with the rim of the drum

Turning a velocity takes acceleration

Hold the flywheel at a steady 1,800 rpm. Now α=0\alpha = 0, so at=0a_t = 0. Is the bolt's acceleration zero?

It isn't. Velocity is an arrow, with a length and a direction. The length holds steady, but the arrow keeps swinging around with the bolt, and a change of direction is a change of velocity. Slide the arrows from two moments so their tails meet, and you can see what's left over.

Δθ O Δv P1 P2 v1 v2 the path Δθ Δv v1 v2 the velocity arrows, tails together
The velocity arrow swings, and the change points at the center

With the tails together, the velocity arrow is itself a radius, length vv, turning at the wheel's ω\omega. Its tip is a point on a circle of radius vv, and you know how fast such a point moves: radius times ω\omega. So the velocity changes at the rate vωv\omega, square to the arrow, which aims it at the center. With v=rωv = r\omega, that's the normal acceleration:

an=vω=rω2=v2ra_n = v\omega = r\omega^2 = \frac{v^2}{r}

The Handbook has it in two pieces: ar=−rω2a_r = -r\omega^2 "toward the center of the circle" under Plane Circular Motion, and an=v2/ρa_n = v^2/\rho under Particle Curvilinear Motion, where ρ\rho is the path's radius of curvature. On a circle, ρ\rho is just rr.

Now the square makes sense. Double the speed on the same circle, and the arrow is twice as long and swings twice as fast, so its tip moves four times as fast. And there's the bolt: an=1(188.5)2=35,500 ft/s2a_n = 1(188.5)^2 = 35{,}500\ \text{ft/s}^2, about 1,100 gg, from a wheel whose speed never changes.

A rim point on a wheel that's speeding up has both, at right angles, for a total of a=at2+an2a = \sqrt{a_t^2 + a_n^2}. A cable's straight run isn't going around any circle, so it has no ana_n at all, only rαr\alpha.

Worked Example A hoist drum at one instant
1 of 4

A hoist drum 3 ft in diameter turns at 40 rpm and is speeding up at 2 rad/s22\ \text{rad/s}^2. At that instant, find the cable's speed and acceleration, and the normal acceleration of a point on the drum's rim.

The exam also asks for this reasoning with no real calculation.

Checkpoint
1 of 3

A car drives counterclockwise around a circular track at constant speed. Which diagram shows its acceleration at the instant drawn?

A.
center v a = 0
B.
center v a
C.
center v a
D.
center v a

Something real has to pull inward

Back to the bolt. Newton's Second Law doesn't care which way an acceleration points, so aim it along the normal. The Handbook's Normal and Tangential Kinetics for Planar Problems entry writes:

ΣFn=man=mv2ρ\Sigma F_n = ma_n = m\frac{v^2}{\rho}

Keep ρ\rho for a path's curve and rr for a distance from an axle. The Handbook prints the speed as vtv_t, and it's the same speed. The bolt's mass is (1/16)/32.2=0.00194 slug(1/16)/32.2 = 0.00194\ \text{slug}, so the net inward force on it is 0.00194(35,500)=69 lb0.00194(35{,}500) = 69\ \text{lb}, the other number from the start.

Now for the most tempting mistake in this Lesson. Take a curve briskly with a coffee cup on the dash. The cup slides to the outside, you get pressed against the door, and it feels like something's shoving you outward. Nothing is. The dash can't grip the cup hard enough to turn it with the car, so the cup carries on nearly straight while the car turns out from under it. The door is pushing you inward, and that's the real force.

car's path start later cup keeps going straight toward center of curve
Seen from above, the cup goes straight and the car turns

So a free-body diagram never carries a "centrifugal force." Every force needs a source, either gravity or something touching the body, and nothing out there is pulling outward. And mv2/ρmv^2/\rho isn't a force either. Like mama, it's what the real forces have to add up to.

The moves are the same as before, with the axis aimed at the center. The only new question is who supplies the pull. On a flat road, only friction can. On ice, the tires can't deliver it, and the car isn't flung outward. It just keeps going straight.

Tilt the road and the normal force does the turning

So tilt the road toward the center of the curve. Pavement pushes square to its surface, so the normal force now leans inward, and part of it aims at the center. Get the tilt right for the speed, and that part is exactly the pull the car needs, with no help from the tires.

This looks like the incline in Newton's Second Law, and it isn't. A block on an incline accelerates along the slope. This car circles at one height, so its acceleration is horizontal. The axis goes horizontal too, and this time NN is the force that gets split.

θ toward center of curve W θ N N cos θ N sin θ a = v2/ρ
A car on a frictionless banked curve, seen from behind
vertical:Ncos⁡θ=Whorizontal:Nsin⁡θ=Wgv2ρ\begin{aligned} \text{vertical:}\quad N\cos\theta &= W \\[4pt] \text{horizontal:}\quad N\sin\theta &= \frac{W}{g}\frac{v^2}{\rho} \end{aligned}

Divide the second by the first, and both NN and WW disappear:

tan⁡θ=v2gρ\tan\theta = \frac{v^2}{g\rho}

A truck and a bicycle need the same bank. And N=W/cos⁡θN = W/\cos\theta is more than the weight, where the incline's Wcos⁡θW\cos\theta was less.

The Handbook doesn't print this formula. Its Horizontal Curves table does print a highway form with side friction and speed in mph, which Superelevation and Sight on Curves picks up.

Worked Example Banking for a speed
1 of 3

A frictionless curve has a radius of 500 ft. Find the bank angle that needs no side friction at 45 mph.

Over a crest, the road lets go

Crest a hill quickly and your stomach floats. The car is on a circle whose center is below the road, so its acceleration points down, like the elevator in Newton's Second Law with its scale reading low.

center of curvature ρ v W N a = v2/ρ
A car at the top of a crest

Two forces act, WW down and NN up, with the axis down toward the center:

W−N=Wgv2ρW - N = \frac{W}{g}\frac{v^2}{\rho}

The road pushes less the faster you go. A road can only push, so NN stops at zero, where the weight alone is exactly the pull the circle needs:

N=0⇒v=gρN = 0 \quad\Rightarrow\quad v = \sqrt{g\rho}

Any faster, and the car leaves the road. In a sag, the center is above you and NN is more than WW. The Handbook prints none of this, only ΣFn\Sigma F_n to build it from.

Worked Example A car over a hill
1 of 3

A 3,000 lb car travels at 45 mph over a crest with a radius of curvature of 400 ft. Find the normal force on it at the top, and the speed in mph at which it would leave the road.

A cord in a vertical circle

Whirl a ball on a cord in a vertical circle, so ρ\rho is the cord's length. The cord can only pull, so its tension always aims at the center, while gravity always aims down. At the top they point the same way. At the bottom they fight.

ρ O T W v a top: T + W = mv2/ρ T W v a bottom: T − W = mv2/ρ
The same ball at the top and bottom of its circle
top:T+W=Wgv2ρbottom:T−W=Wgv2ρ\begin{aligned} \text{top:}\quad T + W &= \frac{W}{g}\frac{v^2}{\rho} \\[4pt] \text{bottom:}\quad T - W &= \frac{W}{g}\frac{v^2}{\rho} \end{aligned}

So at the same speed, the cord at the bottom carries 2W2W more than at the top. At the bottom it has to turn the ball and hold it up, and at the top gravity does part of the turning for free. A ball in a free swing moves faster at the bottom, so a problem gives you the speed at the point it asks about.

Worked Example A ball on a cord
1 of 3

A 2 kg ball is whirled on a 1.2 m cord in a vertical circle at a steady 6 m/s. Find the cord tension at the top and at the bottom.

Recap

  • θ\theta, ω\omega, and α\alpha do what ss, vv, and aa do, in radians: rpm times 2π/602\pi/60, revolutions times 2π2\pi.
  • Every point of a rigid body shares ω\omega and α\alpha, while v=rωv = r\omega and at=rαa_t = r\alpha grow with radius. A belt or cable moves with the rim.
  • Turning a velocity takes acceleration, even at constant speed: an=rω2=v2/ra_n = r\omega^2 = v^2/r toward the center, four times as much at twice the speed on the same circle.
  • ΣFn=mv2/ρ\Sigma F_n = mv^2/\rho, from real forces only. No centrifugal force goes on a free-body diagram.
  • A frictionless bank needs tan⁡θ=v2/(gρ)\tan\theta = v^2/(g\rho). Over a crest, NN falls below WW, reaching zero at v=gρv = \sqrt{g\rho}. A cord pulls hardest at the bottom of its circle, where T−W=mv2/ρT - W = mv^2/\rho.