Work and Energy

When speeds are tied to distances, energy skips the acceleration entirely.

Before this Lesson

A crate starts from rest and slides down a frictionless chute that drops 20 ft. It's steep at the top, nearly flat in the middle, and steep again at the end, so its acceleration changes every foot, and the constant-acceleration equations are out. Newton's second law still holds, but you'd need the chute's exact shape to use it, and nobody gave you that.

You don't need it. The speed at the bottom takes one line, whatever the shape and whatever the crate weighs, once you get the acceleration out of the way.

Cut out the acceleration

In Newton's Second Law, a net force of 30 lb took a 200 lb crate from rest to 10 ft/s. To find how far it went, you computed a=4.83 ft/s2a = 4.83\ \text{ft/s}^2, used it once, and got 10.4 ft. The acceleration was a middleman, made in one line and used up in the next.

So cut it out. A constant net force ΣF\Sigma F pushes a body of mass mm through a distance dd, taking its speed from v1v_1 to v2v_2:

ΣF=mav22=v12+2ad\Sigma F = ma \qquad\qquad v_2^2 = v_1^2 + 2ad

Solve the second for aa, put it into the first, and tidy up:

(ΣF) d=12mv22−12mv12(\Sigma F)\,d = \tfrac12 mv_2^2 - \tfrac12 mv_1^2

Time and acceleration are both gone. On the left is force through a distance: work, UU. On the right is a quantity that depends only on mass and speed: kinetic energy, which the Handbook's Principle of Work and Energy section writes as T=12mv2T = \tfrac12 mv^2. So the kinetic energy at the end is what the body had at the start, plus the work done on it:

T2=T1+UT_2 = T_1 + U

Run the crate again: T1=0T_1 = 0, the work is 30d30d, and T2=12(200/32.2)(102)=310.6 ft-lbT_2 = \tfrac12(200/32.2)(10^2) = 310.6\ \text{ft-lb}, so d=10.4 ftd = 10.4\ \text{ft} with no acceleration anywhere. Notice the m=W/gm = W/g: in U.S. units, a weight still becomes a mass before it goes into 12mv2\tfrac12 mv^2. Energy comes out in ft-lb, or in SI, N·m, the joule (J). And in this Lesson, TT means kinetic energy, so a tension gets written out in words.

If the force varies, slice the path so finely that the force barely changes over each piece, and add this line up over all of them. The energies in the middle cancel in pairs. So work-energy is ΣF=ma\Sigma F = ma summed over distance.

What counts as work

A force does work only through the part of it along the motion. Pull a crate with a rope at an angle θ\theta to its path, and Fcos⁡θF\cos\theta drags it along while Fsin⁡θF\sin\theta just tries to lift it. That's the constant-force row of the Handbook's Work table:

U=Fdcos⁡θU = Fd\cos\theta
d θ F sin θ F cos θ F W N
A rope pulling a crate at an angle to its path

The cosine handles the sign too. A force along the motion adds energy, and one against it, at 180°, takes energy out. A force square to the motion, at 90°, does no work at all.

That last one will offend anyone who has ever carried a couch. Your arms ache, but they push straight up while the couch moves sideways, so they do no work on it. Work in mechanics isn't effort. It's what changes speed. So a normal force from a fixed surface does no work, and neither does a pendulum cord's tension, always square to the swing. A fixed pin's reaction does none either, because the pin doesn't move. The Handbook doesn't list these, but its Work table implies them.

Now the chute. The normal force does no work, which leaves the weight. On one short piece of path, dsds, at an angle θ\theta to the weight, the work is Wcos⁡θ dsW\cos\theta\,ds, and dscos⁡θds\cos\theta is just that piece's vertical drop, dydy. A steep piece has more of the weight along it, a shallow piece is longer for the same drop, and they come out even. Add up all the pieces, and the work is WW times the total drop. The shape has vanished.

h 1 2 W N θ dy ds
A frictionless chute with a changing slope

The Work table writes this as UW=−W ΔyU_W = -W\,\Delta y, with yy measured upward, so gravity's work is positive going down. Here's the one line promised at the start, from rest with h=20 fth = 20\ \text{ft}. The weight cancels:

12Wgv2=Wh⇒v=2gh=2(32.2)(20)=35.9 ft/s\frac12\frac{W}{g}v^2 = Wh \quad\Rightarrow\quad v = \sqrt{2gh} = \sqrt{2(32.2)(20)} = 35.9\ \text{ft/s}

When the force changes along the way

A force that varies has no single FF to multiply by. In Integrals and Area, a climbing flow had no single rate to multiply by time, and the water delivered was the area under the flow curve. Same here: on a graph of force against position, height times width is force times distance, so work is the area under the force-position curve. That's the Work table's variable-force row, which for a force along the motion reads:

U=∫x1x2F(x) dxU = \int_{x_1}^{x_2} F(x)\,dx
x F x1 x2 dx F U
Work as the area under a force-position curve

The varying force you'll meet most is a spring's. The Handbook's Elastic Potential Energy entry gives it as Fs=ksF_s = ks, with stiffness kk and deformation ss, the change in length from the undeformed length. Plenty of problems write xx instead. Graphed, the force is a straight line through the origin, so the area under it up to ss is a triangle, 12ks2\tfrac12 ks^2. From s1s_1 to s2s_2, it's the band between them:

12ks22−12ks12\tfrac12 ks_2^2 - \tfrac12 ks_1^2
ks1 ks2 s Fs Fs = ks 0 undeformed length s1 s2 ½ks12 ½ks22 − ½ks12
The work of a spring as area under its force line

It is not 12k(s2−s1)2\tfrac12 k(s_2 - s_1)^2. A spring already pushing back with ks1ks_1 makes every further inch cost more, so measure both deformations from the undeformed length, never from the last position.

The Work table prints Us=−(12ks22−12ks12)U_s = -\left(\tfrac12 ks_2^2 - \tfrac12 ks_1^2\right), and the minus sign carries the direction: a relaxing spring pushes the way the body goes and does positive work, and one deformed further does negative work. The table's other rows use ss for path distance, this Lesson's dd.

Worked Example A force that grows with position
1 of 3

A 64.4 lb block starts from rest at x=0x = 0 on a smooth floor. A force along the floor pushes it with F=20+3x2F = 20 + 3x^2 lb, where xx is in feet. Find its speed at x=4 ftx = 4\ \text{ft}.

Work that comes back

Lift a crate 20 ft, and you've done W(20)W(20) of work on it, with no speed to show for it. But nothing is lost. Let go, and gravity hands it all back as speed. A compressed spring is the same deal. Stored work is potential energy, and the Handbook's Potential Energy entry gives both kinds:

Vg=WyVe=12ks2V_g = Wy \qquad\qquad V_e = \tfrac12 ks^2

Here yy is the elevation above a datum you get to pick, since only changes in VV matter, and the Handbook also writes mghmgh. And ss is still measured from the undeformed length.

With gravity and springs moved over to VV, the only work left to count is everything else: friction, a rope, a hand. That's the Handbook's Principle of Work and Energy:

T2+V2=T1+V1+U1→2T_2 + V_2 = T_1 + V_1 + U_{1\to2}

U1→2U_{1\to2} counts only forces not already in VV, so gravity goes in once, as VV or as work, never both. When nothing else does work, U1→2=0U_{1\to2} = 0, and what's left is the Handbook's law of conservation of energy, T2+V2=T1+V1T_2 + V_2 = T_1 + V_1. Energy shuffles between TT and VV, and the total holds still.

To use it, pick two states and a datum, write TT and VV at each, and put the work of anything else in U1→2U_{1\to2}.

A pendulum is a good first test. The tension does no work, so the one thing to work out is geometry. Released at θ\theta from the vertical, the bob starts Lcos⁡θL\cos\theta below the pivot and ends LL below it, so it drops h=L(1−cos⁡θ)h = L(1 - \cos\theta).

θ L cos θ h = L(1 − cos θ) L 2 1 tension motion
How far a pendulum bob drops
Worked Example A pendulum released from an angle
1 of 3

A pendulum with an 8 ft cord is released from rest at 60° from the vertical. Find the bob's speed at the bottom of its swing.

Springs go into VV the same way. Compress one by ss against a block on a smooth surface and let go. At state 1, everything is in the spring. The block leaves when the spring is back to its undeformed length, so at state 2, everything is in the speed:

12ks2=12Wgv2\tfrac12 ks^2 = \tfrac12\frac{W}{g}v^2
Worked Example A spring launch
1 of 2

A spring with k=50 lb/ink = 50\ \text{lb/in} is compressed 4 in against a 16.1 lb block on a smooth floor, then released. Find the block's speed after it leaves the spring.

Friction takes its share for good

Gravity and springs keep what you give them. Friction doesn't. Slide a block across a rough floor, and its kinetic energy goes into warming the block and the floor. It never pays any of that back, so it has no VV and stays in U1→2U_{1\to2}.

Smooth chute Rough chute V = 200 ft-lb T = 200 ft-lb V = 200 ft-lb T = 140 ft-lb friction took 60 ft-lb Top Bottom Top Bottom
The same 10 lb crate on a chute that drops 20 ft, smooth and rough

Friction points against the sliding, so it's the constant-force row with θ=180∘\theta = 180^\circ. The Handbook prints no row of its own for it, but says that forces such as friction make U1→2U_{1\to2} negative:

U1→2=−μkNdU_{1\to2} = -\mu_k N d

NN is still whatever the surface must supply: WW on a level floor and Wcos⁡θW\cos\theta on an incline. And an incline has two distances: friction acts over the whole slide, dd, and gravity sees only the vertical drop, dsin⁡θd\sin\theta.

θ 2 d sin θ d 1 W N = W cos θ F = μk N sliding
Two distances on a rough incline

The same equation finds an unknown force. When a rolling cart hits a bumper, the bumper's force varies in ways nobody told you, but the constant force doing the same work over the same distance is the average resisting force, so Favgd=T1F_{\text{avg}}d = T_1. A falling hammer brought to rest works the same way, with gravity on the books too.

Worked Example A block on a rough incline
1 of 4

A 50 lb block moving at 8 ft/s slides 15 ft farther down a 30° incline, with μk=0.20\mu_k = 0.20. Find its speed at the end of the 15 ft.

Catching a body with a spring

Drop a block onto a spring and ask how far the spring compresses. It's tempting to think the fall ends when the block touches the spring. It doesn't. The block keeps going down until the spring has stopped it, so gravity works through the drop hh and the compression ss together.

y = 0 h s h + s 1: released from rest 2: lowest point, momentarily at rest
A block dropped onto a spring, and its lowest point

State 1 is the release, and state 2 is the lowest point, momentarily at rest. With the datum at state 2, both TTs are zero and U1→2=0U_{1\to2} = 0, so:

W(h+s)=12ks2W(h + s) = \tfrac12 ks^2

That's a quadratic in ss, so use the quadratic formula or your calculator's equation solver and keep the positive root. A body sliding on a level floor into a spring has no drop at all, so T1=12ks2T_1 = \tfrac12 ks^2. On a slope, the block goes on descending during the compression, just not as steeply.

Worked Example A block dropped onto a spring
1 of 3

A 50 lb block is dropped from rest 3 ft above the top of a spring with k=400 lb/ftk = 400\ \text{lb/ft}. Find the spring's maximum compression.

Is time given, or distance?

You now have two main routes through a dynamics problem, and one question picks between them: is time given, or distance? The work-energy equation has no tt in it, so when a problem ties speeds to distances, it gets there in a line or two. When a problem brings in time, or wants an acceleration or a tension at some moment, that equation has nothing to offer, and it's back to ΣF=ma\Sigma F = ma, or its time-based form from Impulse and Momentum.

Energy also shows how answers scale. A block stopped by friction on a level floor gives 12(W/g)v2=μkWd\tfrac12(W/g)v^2 = \mu_k Wd. The weight cancels, leaving the braking result from Constant-Acceleration Motion, with μkg\mu_k g as the deceleration:

d=v22μkgd = \frac{v^2}{2\mu_k g}

The spring launch from earlier, solved for speed, gives:

v=skmv = s\sqrt{\frac{k}{m}}
Checkpoint
1 of 3

Which of these is most directly solved with work-energy?

A.
A 3,000 lb car is pushed by a net 600 lb force for 5 s from rest. Find its final speed.
B.
A 3,000 lb elevator car accelerates upward at 4 ft/s². Find the cable tension.
C.
A 3,000 lb car skids to rest over 120 ft with a known friction coefficient. Find its initial speed.
D.
Two blocks joined over a pulley start from rest. Find how long they take to reach 6 ft/s.

Recap

  • Work-energy is ΣF=ma\Sigma F = ma summed over distance. With no time or acceleration in it, it's the direct route when speeds are tied to distances.
  • Work is Fdcos⁡θFd\cos\theta, or the area under a force-position curve. Forces square to the motion and fixed pins do none.
  • T=12mv2T = \tfrac12 mv^2 with m=W/gm = W/g, Vg=WyV_g = Wy, and Ve=12ks2V_e = \tfrac12 ks^2. Spring work uses s22−s12s_2^2 - s_1^2, never (s2−s1)2(s_2 - s_1)^2, and a body landing on a spring keeps falling through the compression.
  • T2+V2=T1+V1+U1→2T_2 + V_2 = T_1 + V_1 + U_{1\to2} counts only forces not in VV. Friction's −μkNd-\mu_k Nd never comes back.
  • Doubling an initial speed quadruples the stopping distance against friction. Doubling a spring's compression doubles the launch speed.