Impulse and Momentum

A long, gentle push and a short, hard one can change motion by exactly the same amount.

Before this Lesson

A 3,220 lb car leaves the highway at 60 mph, aimed at a concrete bridge pier. Say the pier stops it in a tenth of a second. Now line up those yellow sand-filled barrels you see at off-ramps in front of the pier, and say they stretch the stop out to a full second.

Same car, same speed, and stopped either way. The barrels can't reduce how much stopping there is to do. So what are they for?

Newton's second law, summed over time

Start from Newton's Second Law. A steady net force gives a steady acceleration, and that acceleration is the change in velocity over the time it took:

ΣF=ma=m v−v0Δt\Sigma F = ma = m\,\frac{v - v_0}{\Delta t}

Multiply through by the time:

ΣF Δt=mv−mv0\Sigma F\,\Delta t = mv - mv_0

There's no new physics here, only Newton's law with the acceleration swapped out, but both sides earn names. On the right, mvmv is the body's momentum: its mass times its velocity. On the left, force times time is the impulse. So impulse equals change in momentum. A force doesn't change motion just by being large. What counts is how large, for how long.

Now the barrels make sense. The car's mass is 3,220/32.2=100 slugs3{,}220/32.2 = 100\ \text{slugs}, and 60 mph is 88 ft/s, so it carries 100(88)=8,800 lb⋅s100(88) = 8{,}800\ \text{lb}\cdot\text{s} of momentum. That has to reach zero whatever the car hits, so the impulse is the same either way. Only the time is up for negotiation:

pier:F=8,8000.1=88,000 lbbarrels:F=8,8001.0=8,800 lb\begin{aligned} \text{pier:}\quad F &= \frac{8{,}800}{0.1} = 88{,}000\ \text{lb} \\[4pt] \text{barrels:}\quad F &= \frac{8{,}800}{1.0} = 8{,}800\ \text{lb} \end{aligned}

Those are averages, since no crash pushes steadily. Ten times the time, a tenth of the force. That's the whole job of the barrels. On a graph of force against time, each impulse is the area under the line, and these two stops look nothing alike and have exactly the same area.

0 0.2 0.4 0.6 0.8 1.0 1.2 0 20,000 40,000 60,000 80,000 100,000 t (s) F (lb) Pier: 88,000 lb for 0.1 s Area = 8,800 lb·s Barrels: 8,800 lb for 1.0 s Area = 8,800 lb·s
The same impulse, delivered two ways

Impulse comes in lb·s or N·s, and momentum in slug·ft/s or kg·m/s. Those are the same units, since 1 slug = 1 lb·s²/ft and 1 N = 1 kg·m/s², so nothing needs converting.

The Handbook's Impulse and Momentum section, under Linear Momentum, writes the same result for a whole system of particles between times t1t_1 and t2t_2:

Σmi(vi)t2=Σmi(vi)t1+Σ∫t1t2Fi dt\Sigma m_i (\mathbf{v}_i)_{t_2} = \Sigma m_i (\mathbf{v}_i)_{t_1} + \Sigma \int_{t_1}^{t_2} \mathbf{F}_i \, dt

The last term is the impulse. For one body under a steady net force, it boils down to the form you'll use most:

mv0+ΣF Δt=mvmv_0 + \Sigma F\,\Delta t = mv

The Handbook's bold letters mark a vector equation, written once per direction. Every problem here runs along one line, so you need one equation and one positive direction.

Is time given, or distance? When a problem ties a force to a time, this is the direct route, with no acceleration at all. The 200 lb crate from the last Lesson, under 30 lb of net force, reaches 10 ft/s from rest in one line: Δt=(200/32.2)(10)/30=2.07 s\Delta t = (200/32.2)(10)/30 = 2.07\ \text{s}, the answer that took two steps there. Notice that 30 lb: it's the net force that changes momentum, so friction comes off first.

Worked Example A crate pushed along a rough floor
1 of 3

A 300 lb crate is sliding across a rough level floor at 4 ft/s, with μk=0.20\mu_k = 0.20, when a constant 120 lb horizontal push starts acting in the direction it's moving. Find its speed 3 s later.

In a rebound, the reversal counts

So far every velocity has pointed the same way. Bounce a ball off a wall and that's over. The wall has two jobs: stop the ball, then send it back. Momentum is a vector, and one positive direction keeps the books straight.

Say a ball arrives at 60 ft/s and leaves at 40 ft/s. Take away from the wall as positive, so v0=−60 ft/sv_0 = -60\ \text{ft/s} and v=+40 ft/sv = +40\ \text{ft/s}:

Δv=v−v0=40−(−60)=100 ft/s\Delta v = v - v_0 = 40 - (-60) = 100\ \text{ft/s}

The minus signs turn into a plus, so a rebound's change in velocity is the sum of the two speeds. Subtract the speeds instead and you get 20 ft/s, which is hardly a fair description of a ball that turned completely around.

+ Before 60 ft/s After 40 ft/s −60 −40 −20 0 +20 +40 v (ft/s) v0 = −60 v = +40 Δv = 100 ft/s
A rebound's change in velocity crosses zero

The impulse is m Δvm\,\Delta v. Divide it by the contact time and you get the average contact force on the ball, the steady force that would deliver the same impulse in the same time. The ball pushes back on the wall just as hard. A water jet turned around by a vane is this same reversal, kept up continuously, in Forces from Jets on Plates and Vanes.

Worked Example A ball off a wall
1 of 3

A 0.25 lb ball strikes a wall at 80 ft/s and rebounds along the same line at 50 ft/s. Contact lasts 0.005 s. Find the impulse on the ball and the average contact force.

Impulse is the area under the force-time graph

Contact forces aren't steady. A ball hitting a wall squashes, so the force climbs to a peak and falls away as the ball springs back. To handle that, slice the time so thin that the force is steady within each slice. Each slice's impulse is F dtF\,dt, a thin strip of area under the graph. Add up the strips:

impulse=∫F dt=area under the force-time graph\text{impulse} = \int F\,dt = \text{area under the force-time graph}

That's the integral in the Handbook's equation, though the Handbook prints no graph. It's also a move you know from Position, Velocity, and Acceleration, where the area under a velocity-time graph was displacement.

Exam graphs come in two shapes. A rectangle has an area of F ΔtF\,\Delta t. A triangle has an area of 12Fmax⁡ Δt\tfrac{1}{2}F_{\max}\,\Delta t, wherever its peak falls. Either way, the average force is the area divided by the duration. For the rectangle that's just its height. For the triangle it's half the peak, and that's the number to keep straight, because the peak is the one printed on the graph.

t F Fmax Favg = Fmax/2 Δt
A triangular pulse and the steady force with the same area
Worked Example A triangular pulse on a block
1 of 3

A 64.4 lb block at rest on a smooth level surface feels the horizontal force graphed here. Find its speed after the pulse and the average force during it.

0 0.1 0.2 0.3 0.4 0.5 0.6 0 10 20 30 40 50 t (s) F (lb) 40 lb
Force on the block against time

In a collision, momentum just changes hands

Now give that contact force a twin. When body 1 pushes on body 2, body 2 pushes back on body 1, equally and oppositely at every instant. That's Newton's third law. And they touch for exactly the same time, since one can't stop touching the other alone. So their force-time graphs are mirror images, and their impulses are equal and opposite.

+ 1 2 F F t F Same contact time Force on body 2 Impulse on 2 Impulse on 1 Force on body 1 Equal areas, opposite signs
Equal and opposite forces, for the same time

Whatever momentum one body gains, the other loses, so the total doesn't change, whether the bodies bounce, crumple, or lock together. That needs the two to interact only with each other. Tires and rails still feel friction during an impact, but over a fraction of a second those impulses are tiny beside the contact force's, so you ignore them.

The Handbook's Impact section gives this for a direct central impact, which is a head-on collision, with no external forces. Primes mean just after impact:

m1v1+m2v2=m1v1′+m2v2′m_1 v_1 + m_2 v_2 = m_1 v'_1 + m_2 v'_2

Every velocity carries its sign, so a body moving against your positive direction goes in as a negative number. If the bodies couple, they share one velocity after impact, so the right side is (m1+m2)v′(m_1 + m_2)v'.

Take a 64,400 lb railcar rolling at 6 ft/s into a 32,200 lb car at rest, coupling on contact. Their masses are 2,000 and 1,000 slugs:

2,000(6)+0=(2,000+1,000)v′⇒v′=4 ft/s2{,}000(6) + 0 = (2{,}000 + 1{,}000)v' \quad\Rightarrow\quad v' = 4\ \text{ft/s}

Now run a different tally, kinetic energy, which the Handbook's Principle of Work and Energy section writes as:

T=12mv2T = \tfrac{1}{2}mv^2

For now, treat it as a number to compute before and after, in ft·lb or joules. Work and Energy will show you what it means. Before: 12(2,000)(62)=36,000 ft⋅lb\tfrac{1}{2}(2{,}000)(6^2) = 36{,}000\ \text{ft}\cdot\text{lb}. After: 12(3,000)(42)=24,000 ft⋅lb\tfrac{1}{2}(3{,}000)(4^2) = 24{,}000\ \text{ft}\cdot\text{lb}.

Before 64,400 lb 32,200 lb at rest 6 ft/s Momentum = 12,000 lb·s T = 36,000 ft·lb After 64,400 lb 32,200 lb 4 ft/s Momentum = 12,000 lb·s T = 24,000 ft·lb
Two railcars coupling: one tally holds, one doesn't

A third of it is gone, into bent couplers, heat, and noise. The Handbook puts it in one line: "momentum is conserved while energy may or may not be conserved." For the extreme case, run two identical cars head-on at the same speed and let them lock. The total momentum is zero before and zero after, so momentum is perfectly content with a motionless wreck, and every bit of the kinetic energy is gone.

How bouncy? The coefficient of restitution

Coupling is one extreme. Usually the bodies bounce apart, and then momentum alone falls short: one equation, two unknowns, v1′v'_1 and v2′v'_2. The missing fact is how bouncy the collision is.

Watch the gap between the bodies. Before impact it closes at v1−v2v_1 - v_2. After impact it opens at v2′−v1′v'_2 - v'_1. Their ratio is the coefficient of restitution, from the same Impact section:

e=v2′−v1′v1−v2e = \frac{v'_2 - v'_1}{v_1 - v_2}

The Handbook tags each velocity with a subscript nn, for the direction normal to the plane of impact. A head-on collision has only that one direction, so this Lesson drops it. Note what ee compares: relative velocities, with signs, and not one body's speed against another's. Only against a wall that doesn't move does it reduce to rebound speed over approach speed.

+ Before impact m1 m2 v1 v2 Gap closes at v1 − v2 After, coupled (e = 0) m1 m2 v′ After, separating m1 m2 v′1 v′2 Gap opens at v′2 − v′1
The gap closes before impact and opens after it
Every velocity here is drawn positive, to the right. A body moving left would carry a negative velocity.
What the value of e means
ValueNameAfter impactKinetic energy
e=0e = 0Perfectly plasticNo rebound, move togetherGreatest loss
0<e<10 < e < 1In betweenGap opens, but slowerSome lost
e=1e = 1Perfectly elasticGap opens just as fastConserved

Adapted from the FE Reference Handbook, Impact

So a head-on collision comes down to two equations: momentum, plus either the restitution equation or the shared v′v'. The Impact section also prints both already solved for v1′v'_1 and v2′v'_2. They give the same answers, but the two equations keep your signs in plain view.

Worked Example Two blocks that bounce apart
1 of 4

On a smooth surface, a 10 kg block moving right at 6 m/s hits a 5 kg block moving left at 3 m/s, head-on, with e=0.5e = 0.5. Find each block's velocity just after impact and the kinetic energy lost.

Recap

  • Impulse equals change in momentum: mv0+ΣF Δt=mvmv_0 + \Sigma F\,\Delta t = mv. It's ΣF=ma\Sigma F = ma summed over time, so use the net force and, in U.S. units, m=W/gm = W/g.
  • Use one positive direction. A rebound's change in velocity is the sum of the two speeds.
  • Impulse is the area under the force-time graph. Same area, same change in velocity. A triangular pulse has an area of 12Fmax⁡ Δt\tfrac{1}{2}F_{\max}\,\Delta t, and an average force of half its peak.
  • In a collision, the two impulses are equal and opposite, so m1v1+m2v2=m1v1′+m2v2′m_1 v_1 + m_2 v_2 = m_1 v'_1 + m_2 v'_2. Kinetic energy usually drops, so tally 12mv2\tfrac{1}{2}mv^2 before and after.
  • e=(v2′−v1′)/(v1−v2)e = (v'_2 - v'_1)/(v_1 - v_2) compares relative velocities: the gap opening over the gap closing. Coupled bodies have e=0e = 0 and share one v′v'.