Licensure, Seals, and Responsible Charge

A seal is a signature on your own work, never a rubber stamp on someone else's.

Before this Lesson

A homebuilder calls on a Tuesday. The company's designer, who isn't licensed, has drawn a 14-sheet house plan, and the city wants an engineer's seal by Friday. "Check it as hard as you like," the builder says. "I'll pay you $1,000 to seal it."

You spend a full day on it. You mark up two small errors, they get fixed, and now the drawings are right. The work is correct and the fee is fair. So is there anything left to object to?

What the mark says

Start with what a seal is. The Handbook's Model Law defines it without any drama: "a symbol, image, or list of information." You could carve one from a potato. Everything it means comes from the rules about when you may use it.

Think about who reads it. A building official with forty permit sets on the desk can't rerun your calculations, and the family moving into the house couldn't read them. They rely on that mark, because it tells them one named person has made a promise about this work. Two rules fix what the promise is. You met the first in Professional Competence: rule B.2 bars a seal on any document "not prepared under their responsible charge." The second is A.2:

Licensees shall sign and seal only those plans, surveys, and other documents that conform to accepted engineering and surveying standards and that safeguard the health, safety, and welfare of the public.

Put them together and a seal is a sentence, spoken in the first person to people you'll never meet.

"I controlled this work." Prepared by me or under my responsible charge (rule B.2) "It meets accepted standards." Conforms to accepted standards and safeguards the public (rule A.2) Sheet S-2
What a seal says to whoever reads it

Look at what neither rule mentions: the client's wishes, the fee, or the deadline.

Checkpoint
1 of 2

A developer asks you to seal plans for an apartment building. You know the balcony guardrails fall short of the height the code requires. "The inspector here never checks that," the developer says, "and I'll sign a letter accepting the risk." What should you do?

A.
Seal the plans, since the developer has accepted the risk in writing
B.
Seal the plans, and add a note on the sheet that lists the guardrail deviation
C.
Decline to seal them unless the guardrails are brought up to code
D.
Seal the plans, then mention the guardrails to the building official afterward

Control, not a look at the end

The promise rests on responsible charge, so here's what the term means. The Handbook's Model Law defines it, under Definitions, as exercising "full professional knowledge of and control over work." A licensee in responsible charge must:

  • have and exercise the authority to review and to change, reject, or approve "both the work in progress and the final work product";
  • be personally aware of the project's scope, needs, limitations, and special requirements;
  • be capable of answering questions about the engineering decisions made; and
  • "accept full responsibility for the work."

You'll also see all that boiled down to "direct control and personal supervision," an older phrase this Handbook doesn't print. It means the same thing.

Look at the first item again: "work in progress." Why isn't a careful check at the end just as good? Because a check can only test what's on the page. You can recheck every beam on those 14 sheets. You can't see the snow drift nobody thought about, the soil report nobody ordered, or the framing scheme dropped for a bad reason on the second day. Those decisions were over before the sheets existed. An engineer in control was there when they were made, and could have changed them.

Scope and assumptions Calculations Drawings Finished set Responsible charge You: direct, review, change, reject, approve Seal Review at the end Someone else makes the decisions You: check No seal
The same finished set, reached two ways
Checkpoint
1 of 2

Which of these does responsible charge require?

A.
Direct control and personal supervision of the work
B.
A position as a principal or owner of the firm
C.
Authority to review and to change, reject, or approve the work in progress and the final product
D.
A detailed check of the finished drawings, in place of involvement along the way
E.
Personal awareness of the project's scope, limitations, and special requirements

Rubber stamps

Sealing work you didn't control is called plan stamping. The Handbook doesn't use that name, but the Model Law's grounds for disciplinary action include "signing, affixing, or permitting the licensee's seal or signature to be affixed" to documents "which have not been prepared by the licensee or under the licensee's responsible charge." Note "permitting": leaving your stamp in a drawer for the office to use counts too.

Plan stamping rarely feels like fraud. It feels like a favor, a fair fee, or a careful review. So don't judge it by how it feels. Ask one question: was this prepared by me, or under my responsible charge?

If the answer is no, you have two honest moves. Decline, or redo the design as your own work, making the engineering decisions yourself or directing whoever does, from the beginning. The usual workarounds don't get you there. Marking up corrections is a review. A note limiting your seal to a review still leaves a seal on the sheet. Signing beside the preparer adds a name without adding any control.

Worked Example The builder's finished set
1 of 3

Back to Tuesday's call. The builder's unlicensed designer drew a 14-sheet house plan. You've checked every sheet, the two errors you marked are fixed, and the builder offers $1,000 for your seal so the set can go in for its permit. What is the proper response?

One seal, two conditions

B.2 has another half, the one the competence Lesson leaned on: no seal on "subject matter in which they lack competence." So a seal has to clear two conditions, competence in the field and control of the work, and neither one substitutes for the other.

You controlled the work You didn't control the work Competent in the field Not competent in the field Don't seal A builder's drainage set you only checked Don't seal HVAC sheets drawn under your supervision Don't seal Another firm's electrical set Seal it Your own drainage design
A seal needs both conditions

The multidisciplinary project is the same grid with more people on it. Rule B.3 ties each technical segment to the licensee responsible for preparing it, because that's the one person who holds both conditions for that segment. Coordinating is real work, but it isn't control of how someone else's segment gets designed.

The habit, finished

Eliminate any answer that puts profit, convenience, or loyalty ahead of public safety. Eliminate any answer that has the engineer practicing outside their competence or sealing work they didn't control. Among what remains, pick the most transparent option that uses proper channels.

Checkpoint

You coordinate the design of a highway interchange, and your group prepares the roadway segment. A licensed subconsultant prepares the bridge segment. You're an experienced bridge engineer yourself, and you review that segment carefully. A licensed geotechnical engineer at another firm prepares the foundation segment. Who seals what?

A.
You seal the roadway segment, and the subconsultant and the geotechnical engineer each seal the segment they prepared
B.
You seal all three segments, since you're responsible for the project as a whole
C.
You seal the roadway and bridge segments, and the geotechnical engineer seals the foundation segment
D.
You seal one cover sheet for the whole set, so the segments themselves can go out unsealed

Other hands on the work

If you may seal only what you controlled, do you have to draw every sheet yourself? No, or no engineer's office would ever finish anything. The Handbook's Exemption Clause allows "the work of an employee or a subordinate" of a licensee, with a condition attached:

provided such work does not include final engineering or surveying designs or decisions and is done under the responsible charge of and verified by an individual holding a certificate of licensure

That reaches the drafter, the technician, and the engineer intern, which is what most people become soon after passing the exam you're studying for. The clause doesn't name interns, but they're employees like anyone else. Read it closely: it names one thing such work can't include, and two things that must happen to it.

Checkpoint

An engineer intern and an unlicensed drafter are working on a retaining wall that you direct. How does the work have to divide?

A.
You prepare all the calculations and drawings yourself, since unlicensed staff may not do engineering work
B.
The intern makes the final design decisions, since they've passed the FE, and you seal what they decide
C.
The intern seals the calculations, and you seal the drawings the drafter prepared
D.
They prepare calculations and drawings, and you verify the work, make the final decisions, and seal it

Nobody can take it over

Now the uncomfortable half of that arrangement. Say the intern drops a decimal in the wall calculation, you miss it, and you seal the set. Whose error is it? Look at the last line of the definition of responsible charge: "accept full responsibility for the work." It doesn't say "except the parts someone else worked out." You can delegate the calculation. You can't delegate the promise, because the people relying on the mark aren't relying on the intern.

A firm's name on the title block doesn't change that. In 1981, two suspended walkways in the Hyatt Regency in Kansas City fell during a crowded dance, killing 114 people. A change to the hanger rods had doubled the load on a key connection, and it passed through the engineering office without a real check. The engineers worked through a firm, but Missouri's licensing board revoked the licenses of two people: the engineer of record and the project engineer.

The Handbook never mentions insurance, so reason that one out from what a seal says.

Checkpoint

You're a salaried engineer at a corporation with a large professional liability policy. A load error turns up in a set you sealed. A junior engineer made the error, and a vice president tells you, "Relax. That's what the company and its insurance are for." Does any of that relieve you of responsibility?

A.
Yes, because the corporation is the party that contracted for the work and was paid for it
B.
No, because sealing means accepting full responsibility for the work, whoever made the error
C.
Yes, because the firm's insurance policy covers errors in its sealed documents
D.
Yes, because the junior engineer who made the error is the one who should answer for it
E.
No, because the corporation bears no responsibility for errors in documents its engineers seal

Careful, not perfect

Full responsibility doesn't mean you promised perfection. The yardstick is the standard of care: the care a reasonably competent engineer would exercise in similar circumstances. The Handbook doesn't print this one, so you'll have to carry it yourself.

Why not hold engineers to a guarantee? Because engineering runs on incomplete information. You drill a few borings and infer the ground between them, and you design for storms nobody has measured yet. If a bad outcome alone meant you'd failed, nobody could practice. So the test looks at conduct, not results: what would a competent engineer have done with the same information on the same kind of job? It cuts both ways. A failure doesn't prove you were careless, and a success doesn't prove you were careful. Contracts and Professional Liability puts this yardstick to work.

Checkpoint

A foundation settles because of a soft clay pocket that fell between your borings. The owner says, "You're the engineer. It failed, so you fell short." What standard is your work actually judged against?

A.
The care a reasonably competent engineer would exercise in similar circumstances
B.
A guarantee that the finished work will perform as intended
C.
The care of the most expert engineer in the country, whatever the job
D.
Perfection, since a sealed design must be free of every error

Who lets you make the promise

A promise to the public needs someone keeping track of who may make it, and that's what licensure is. In the United States, it's done jurisdiction by jurisdiction: each state, the District of Columbia, and each U.S. territory has its own board. Every time the Handbook's Model Law mentions licensing or discipline, the one acting is "the board."

Other names crowd around licensure, and the exam likes them as wrong answers.

Other names around licensure
BodyWhat it does
NCEESWrites the FE and PE exams, and the Model Law and Rules
ABETAccredits degree programs
ASCE, NSPEProfessional societies you may choose to join

NCEES is the tempting one, since it writes the exam you're studying for. But its Model Law is a template, with no force until a jurisdiction adopts its own version. And a board's reach stops at its boundary, which is why rule A.10 has licensees comply with the licensing laws "in each of the jurisdictions in which they practice."

Checkpoint
1 of 2

Your neighbor passed the NCEES PE exam last spring and carries an ASCE membership card. Who has the legal authority to license your neighbor, and to discipline them for stamping plans?

A.
NCEES, which wrote and administered the exam
B.
ASCE, which sets a code of ethics for its members
C.
The state or jurisdiction licensing board
D.
The federal government, through a national engineering registry
E.
The neighbor's employer, which assigns and supervises the work

The road to a license

You're on this road already. The Handbook's General Requirements for Licensure ask two things for engineer intern certification: an accredited degree and a passed FE exam, with no experience listed. But that certificate isn't a license. The Model Law defines a licensee as a professional engineer or professional surveyor, and its section on unlicensed individuals reaches anyone practicing or offering to practice, using a title that suggests they're a PE, or using a licensee's seal.

Professional engineer licensure asks more: good character and reputation, education, experience, the applicable exams (the FE and the PE), and five references acceptable to the board. That list isn't arbitrary. Each item answers something the board must settle before it lets you make that promise. Do you know the fundamentals? Education and the FE. Can you apply them? Experience and the PE. Can you be trusted? Character and references.

Checkpoint
1 of 3

What does engineer intern certification require?

A.
An accredited degree and a passed FE exam, with no experience requirement
B.
An accredited degree, a passed FE exam, and two years of qualifying experience
C.
A passed FE exam alone, with no degree requirement
D.
A passed PE exam, taken under a licensee's supervision

Here's the whole road in one picture.

Accredited degree FE exam passed Qualifying experience PE exam passed Good character and reputation References Engineer intern Certified by the board. Not a license. Professional engineer Licensed by the board
From degree to license

Source: Adapted from the FE Reference Handbook, General Requirements for Licensure

When someone else breaks the promise

A seal is only worth trusting if licensees police it, because nobody outside the profession can tell a stamped plan from a real one. So rule A.8 makes that your job:

Licensees who have knowledge or reason to believe that any person or firm has violated any rules or laws applying to the practice of engineering or surveying shall report it to the board, may report it to appropriate legal authorities, and shall cooperate with the board and those authorities as requested.

Read the verbs: shall, may, shall. And "reason to believe" means you don't need proof in hand. Don't mix this up with C.4 from Obligations to the Public, the reasonable effort to inform another licensee of an error. An honest error is something to fix together. A violation, such as plan stamping, goes to someone who can act on it.

Rule A.7 covers the firm you might join. Licensees "shall not partner, practice, or offer to practice with any person or firm that they know is engaged in fraudulent or dishonest business or professional practices." Notice whose conduct that rule looks at.

Checkpoint
1 of 2

You learn that an engineer at a nearby firm has been sealing a developer's drawings for a per-sheet fee, without ever being involved in the design. What must you do?

A.
Speak to the engineer privately, and go to the board only if it continues
B.
Report it to the board and cooperate with it, with reporting to legal authorities optional
C.
Report it to legal authorities and cooperate with them, with reporting to the board optional
D.
Give the story to a local reporter, so that the public is warned
E.
Nothing, since neither the engineer nor the project is yours

Recap

  • A seal is a personal promise: I controlled this work, and it meets accepted standards. It needs both competence and responsible charge, so each multidisciplinary segment is sealed by the licensee who prepared it.
  • Responsible charge means direct control and personal supervision as the work develops. A review at the end isn't enough, so decline someone else's finished set, or redo it as your own work.
  • Employees and engineer interns may work under responsible charge, short of final designs or decisions. Only the licensee seals, and no employer, insurer, or subordinate takes over the responsibility. The standard of care is what a reasonably competent engineer would do in similar circumstances, not perfection.
  • The state or jurisdiction board licenses and disciplines, and a license stops at its boundary. An engineer intern has a degree and the FE but no license. A PE adds experience, the PE exam, good character, and references.
  • Report violations to the board and cooperate with it, and decline to join a fraudulent firm.