Shear Stress in Beams

The layers of a beam try to slide past each other, hardest at the neutral axis.

Before this Lesson

Lay two planks one on the other across a ditch and walk out to the middle. They sag, and their ends no longer line up: the top plank now pokes out past the bottom one. Glue them into one block, and the same wood is twice as strong and four times as stiff. All of that rides on one thin glue line at mid-depth, which keeps the planks from sliding, and which turns out to sit in the worst possible place.

Layers that can't slide

Each loose plank bends about its own neutral axis, so where they touch, the bottom of the top plank stretches while the top of the bottom plank shortens. Two surfaces pressed together, one growing and one shrinking, have to slide. Glue stops the slide by gripping both, and that takes a horizontal shear stress along the glue line.

P Loose ends slide apart P Glued glue line
Two planks under one load, loose and then glued

A solid beam is a stack glued by the material itself, so wherever the beam carries shear, its horizontal planes carry horizontal shear stress.

That stress has a vertical twin. A tiny square in the side of the beam carries the internal shear VV as a stress τ\tau, down one vertical face and up the other. That pair is a couple that would spin the square, so its top and bottom faces must carry an equal τ\tau to stop it. At any point, the horizontal and vertical shear stresses are equal. At the beam's top and bottom faces, nothing outside pushes sideways, so both are zero there.

Where the horizontal push comes from

Why does a layer push at all? Cut a slice dxdx long, with moment MM on its left face and M+dMM + dM on its right. Then cut it again at the level you care about, and keep the piece above.

NA cut MQ/I (M + dM)Q/I τ dx M M + dM
The piece above a cut, in a slice where the moment grows

From Bending Stress, the bending stress a distance yy from the neutral axis is My/IMy/I. Over the piece's left face, whose area is A′A', it adds up to a push of:

F=MI∫A′y dA=MQIF = \frac{M}{I}\int_{A'} y\,dA = \frac{MQ}{I}

QQ is the first moment of the piece's area about the neutral axis, as in Centroids of Areas. The right face pushes back harder, with (M+dM)Q/I(M + dM)Q/I. Only the shear on the cut, over a strip bb wide and dxdx long, can hold the difference:

τ b dx=dM QI⇒τ=dMdx QIb=VQIb\tau\,b\,dx = \frac{dM\,Q}{I} \quad\Rightarrow\quad \tau = \frac{dM}{dx}\,\frac{Q}{Ib} = \frac{VQ}{Ib}

The last step uses V=dM/dxV = dM/dx, from Shear and Moment Diagrams. So shear stress lives where the moment changes. Under a constant moment, VV is zero, the two faces push equally, and nothing slides.

The Handbook prints this under Stresses in Beams as the transverse shear stress, τxy=VQ/(Ib)\tau_{xy} = VQ/(Ib), with Q=A′yˉ′Q = A'\bar{y}'. A′A' is the area above the layer, and yˉ′\bar{y}' runs from the neutral axis to its centroid. The Handbook calls bb the width of the cross section, and the derivation says where: across the cut.

Q: how much area, and how far out

Q=A′yˉ′Q = A'\bar{y}' bundles two things: how much area lies beyond the level, and how far from the neutral axis it sits.

NA level b ȳ′ A′
Q for one level of a T-section

Measure yˉ′\bar{y}' from the neutral axis, not the top face, because the push grew with distance from the axis. And bb is the width at the level, not the widest part of the section.

Slide the level down from the top face and watch QQ. At the face, nothing lies beyond, so Q=0Q = 0. Every strip the level passes on the way down lies above the axis and adds to QQ, though less and less as it nears the axis, where its yy is small. So QQ grows until the neutral axis, then shrinks as strips below the axis subtract.

Below the axis, use the part below the level instead. The whole section's first moment about the neutral axis is zero, which is how Bending Stress located the axis, so the parts on either side of a level have the same QQ. Use whichever is simpler. That zero is also why QQ never uses the whole section.

Checkpoint

In a rectangular beam, bb is the same at every level. Which profile shows how the transverse shear stress varies over the depth?

A.
NA
B.
NA
C.
NA
D.
NA

A rectangle's parabola

In a rectangle bb wide and hh deep, the area beyond a level yy above the axis is a strip h/2−yh/2 - y tall, with its centroid halfway up it:

A′=b(h2−y)yˉ′=12(h2+y)Q=b2(h24−y2)A' = b\left(\frac{h}{2} - y\right) \qquad \bar{y}' = \frac{1}{2}\left(\frac{h}{2} + y\right) \qquad Q = \frac{b}{2}\left(\frac{h^2}{4} - y^2\right)

That's a parabola in yy, and with I=bh3/12I = bh^3/12 and bb fixed, so is τ\tau. At the neutral axis, Q=bh2/8Q = bh^2/8:

τmax=V(bh2/8)(bh3/12) b=3V2bh=1.5VA\tau_{\text{max}} = \frac{V(bh^2/8)}{(bh^3/12)\,b} = \frac{3V}{2bh} = 1.5\frac{V}{A}

The Handbook doesn't print this shortcut, but the exam leans on it. The peak is 50% above the average, V/AV/A, because the faces carry none of the shear.

Beside the bending stress, it's the mirror image. Bending stress is largest at the faces and zero at the neutral axis, and shear stress is the reverse. So two planks glued face to face put the glue right on the peak.

Cross section h b Bending stress σmax σmax compression tension average V/A Shear stress NA τmax = 1.5V/A
Bending and shear stress over a rectangle's depth
The bending stress is a straight line, zero at the neutral axis. The shear stress is a parabola, zero at the faces and 1.5V/A1.5V/A at the neutral axis, against an average of V/AV/A.

The largest shear stress in a rectangular beam

The statics half takes VV where the shear is largest, not where the moment is. Under a uniform load, the moment peaks at midspan, where V=0V = 0.

Timber is where this check bites. Wood splits easily along its grain, on exactly the planes where the layers slide. The Handbook's table of Average Mechanical Properties of Typical Engineering Materials gives select structural Douglas fir an ultimate shear strength parallel to the grain of only 0.90 ksi, and it lists no allowable stresses for design, so a question states its own.

Worked Example Shear in a timber beam
1 of 3

The timber beam from Bending Stress is 4 in. wide and 12 in. deep, and it spans 12 ft, simply supported, under 0.5 kip/ft. Find the maximum shear force and the maximum transverse shear stress.

I- and T-sections: the web does the work

In an I or a T, bb changes with the level. Just above and just below the web-flange junction, the area beyond is the same flange, so QQ is the same. But bb drops from the flange width bfb_f to the web thickness twt_w, so the stress jumps by a factor of bf/twb_f/t_w. Inside the web, it keeps rising to the neutral axis, but only a little, because the flange, far from the axis, has already supplied most of QQ. So the flanges carry little shear stress, and the web carries most of VV.

bf tw NA jump at the junction flange: small τmax at NA
Shear stress over the depth of an I-section

Anywhere in the web, bb is the web thickness. And 1.5V/A1.5V/A is the rectangle's alone, so for an I or a T, use the formula. Design codes check steel beams for shear differently, with a formula built on the web's area, in Selecting Steel Beams.

Worked Example A T-section on either side of its junction
1 of 3

This T-section, from Bending Stress, carries a shear of 10 kip. Find the shear stress at the web-flange junction, just below it in the stem and just above it in the flange.

12 in. 2 in. 2 in. 8 in. 7 in. NA web-flange junction I = 333 in4
A T-section with its neutral axis

Working back to a depth

For a rectangle, shear design is one line: keep the peak within the allowable shear stress and solve for the depth.

1.5Vbh≤τallow⇒h≥1.5Vb τallow1.5\frac{V}{bh} \le \tau_{\text{allow}} \quad\Rightarrow\quad h \ge \frac{1.5V}{b\,\tau_{\text{allow}}}

It needs only the largest shear, and no moment. A real beam must pass bending too, but a shear question asks only for this.

Checkpoint
1 of 2

A timber beam 6 in. wide spans 16 ft, simply supported, under 1.2 kip/ft. The allowable shear stress is 150 psi. What is the minimum depth?

in.

Recap

  • Where the moment changes, the bending stresses on nearby sections don't balance, and only shear along a level holds the part beyond it: τ=VQ/(Ib)\tau = VQ/(Ib). Under a constant moment, there's none.
  • Q=A′yˉ′Q = A'\bar{y}', with yˉ′\bar{y}' from the neutral axis. It's zero at the faces and largest at the neutral axis, and either side of a level gives the same QQ.
  • bb is the width at the level: the web thickness anywhere in a web. The stress jumps at a web-flange junction, and the web carries most of the shear.
  • In a rectangle, the shear stress is a parabola, zero at the faces and 1.5V/A1.5V/A at the neutral axis, where the bending stress is zero. The shortcut is for rectangles only.
  • Use the largest shear, usually at a support. For a timber beam, hmin=1.5V/(b τallow)h_{\text{min}} = 1.5V/(b\,\tau_{\text{allow}}).