Composite Sections

Break the section into rectangles, move each one to the axis, and add.

Before this Lesson

A W18X50 steel beam has a moment of inertia of 800 in⁴. Weld a plate 8 in wide and 1 in thick to each flange. Each plate's own II is about 0.67 in⁴, so you might expect to gain a little over 1 in⁴. You gain about 1,445. The steel in those plates is ordinary. What matters is where it sits.

W18X50 W18X50 with plates I = 800 in4 I = 2,245 in4
The same beam, before and after its cover plates

You already own the tools: the part-by-part table from Centroids of Areas and I=Ic+Ad2I = I_c + Ad^2 from Moment of Inertia of Areas. A built-up section is those two run back to back. After that, two new quantities come straight out of II: the radius of gyration and the polar moment of inertia.

Two more columns

Take the T from Centroids of Areas: a 12 in by 2 in flange on a 2 in by 8 in stem, with its centroid 7 in above the bottom edge. Each part brings its own IcI_c, about its own centroid, plus Ad2Ad^2 for being away from the section's centroid. Here AA is that part's area, and dd runs from the part's centroid to the section's.

12 in 2 in 8 in 2 in xc 7 in flange stem d = 2 in d = 3 in
Each part's distance to the T's centroid
The T-section in inches, with the centroid table's columns on the left
Partana_nyny_nynany_n a_nddIcI_cAd2Ad^2
Stem16464385.33144
Flange2492162896
Sum4028093.33240
yac=28040=7.00 inI=∑Ic+∑Ad2=93.33+240=333.3 in4y_{ac} = \frac{280}{40} = 7.00\ \text{in} \qquad I = \sum I_c + \sum Ad^2 = 93.33 + 240 = 333.3\ \text{in}^4

Both columns count. Keep only Ad2Ad^2, and you land 28% low. And for a centroidal II, dd ends at the section's centroid, never at an edge.

Look at how each part earns its share. The flange is thin, so only 8 of its 104 in⁴ is its own IcI_c, and the rest is Ad2Ad^2. The stem is deep, and depth gets cubed, so its IcI_c supplies over a third of its 229 in⁴. A thin part contributes almost entirely through distance, so the farther out you push it, the more it does. That's the job of a beam's flanges.

A named axis skips the centroid

Sometimes the question names the axis: the base, or the line where two parts meet. Then there's no composite centroid to find, because every dd runs to that line. Each part still starts at its own centroid, with a triangle's bh3/36bh^3/36 or a semicircle's 0.1098a40.1098a^4 from the area table.

There's one shortcut. If the line happens to be a row's own xx-axis, the table's IxI_x has already done the transfer. Take the plate from Centroids of Areas, an 8 in by 6 in rectangle capped by a 4 in radius semicircle, about the line where they meet. That line is the rectangle's top edge, which works just like its base, and the semicircle's flat side:

4 in 8 in 6 in axis
A capped plate, with the axis along the joint
I=bh33+πa48=(8)(6)33+π(4)48=576+100.5=676.5 in4I = \frac{bh^3}{3} + \frac{\pi a^4}{8} = \frac{(8)(6)^3}{3} + \frac{\pi(4)^4}{8} = 576 + 100.5 = 676.5\ \text{in}^4
Worked Example An I-section with unequal flanges
1 of 4

The I-section from Centroids of Areas has a 200 mm by 25 mm bottom flange, a 25 mm by 150 mm web, and a 100 mm by 25 mm top flange. Find its moment of inertia about its horizontal centroidal axis.

200 mm 100 mm 25 mm 25 mm 150 mm 25 mm
An I-section with unequal flanges

A hole subtracts its transfer too

A hole is a part with a minus sign, as it was for centroids. Its share about the axis is still Ic+Ad2I_c + Ad^2, and all of it comes off. In Moment of Inertia of Areas, the holes were concentric, so dd was zero. Move the hole off center, and the transfer term is usually the bigger of the two.

I=Isolid−(Ic,hole+Aholed2)I = I_{\text{solid}} - \left(I_{c,\text{hole}} + A_{\text{hole}}d^2\right)

The hole's dd is squared, so the side of the axis it's on doesn't change the sign. For the section's own centroidal axis, locate that centroid first with the hole as a negative area, then transfer both the solid and the hole to it.

Worked Example A plate with an off-center hole
1 of 3

A 12 in by 8 in plate has a 4 in diameter hole centered 9 in from the left edge and 5 in above the bottom edge. Find its moment of inertia about the bottom edge.

12 in 8 in 9 in 5 in 4 in dia. axis
A plate with a hole, and an axis along its bottom edge

Rolled steel comes with its numbers

A rolled shape is one part whose homework has been done. The Handbook's Civil Engineering chapter, under Design of Steel Components, has Table 1-1: W Shapes Dimensions and Properties. W18X50 means about 18 in deep and 50 lb per foot.

Part of the W shape table, with the columns this Lesson needs
ShapeAA (in²)dd (in)IxI_x (in⁴)rxr_x (in)IyI_y (in⁴)ryr_y (in)
W18X5014.718.08007.3840.11.65
W16X3610.615.94486.5124.51.52
W14X4814.113.84845.8551.41.91

Adapted from the FE Reference Handbook, Table 1-1: W Shapes Dimensions and Properties

The table groups its columns under Axis X-X and Axis Y-Y and writes plain II and rr, so IxI_x and IyI_y are my labels. X-X runs horizontally through mid-depth, and Y-Y runs along the web. A W mirrors across both, so both axes pass through its centroid. That makes the table's II the shape's IcI_c, ready for the theorem.

X-X Y-Y dW t dW/2 t/2 d
A W shape's axes, and a cover plate's distance

The Handbook doesn't mention cover plates, and it doesn't need to. The W goes in as one row of the table, and each plate is a rectangle. One thing to watch: the table's dd is the beam's depth, not a transfer distance, so I'll call it dWd_W. A plate of thickness tt sits on the outside of the flange, so the distance from the W's centroid to the plate's is:

d=dW2+t2d = \frac{d_W}{2} + \frac{t}{2}

With equal plates top and bottom, the section's centroid stays at the W's mid-depth, and the W needs no transfer.

Worked Example The beam from the start
1 of 3

A W18X50 has a plate 8 in wide and 1 in thick welded to each flange. Find its moment of inertia about the horizontal centroidal axis.

One length for the whole area

Here's a thought experiment. Squeeze all of a section's area into thin strips, keeping the total the same. How far from the axis must the strips sit to give the same II? With every bit at one distance rr, the integral collapses to I=Ar2I = Ar^2. That distance is the radius of gyration. The Handbook's Statics chapter defines it just this way, under Radius of Gyration:

rx=IxAry=IyAr_x = \sqrt{\frac{I_x}{A}} \qquad r_y = \sqrt{\frac{I_y}{A}}
axis h area A r r A/2 A/2 same A, same I r = 0.289h
A rectangle and two strips with the same area and the same I

It's a measure of spread, not a place where material sits. For a rectangle about its centroidal axis, the width cancels: r2=(bh3/12)/(bh)=h2/12r^2 = (bh^3/12)/(bh) = h^2/12, so r=h/12=0.289hr = h/\sqrt{12} = 0.289h. That's more than h/4h/4, the plain average distance, because far bits count more.

For anything else, the recipe is the same: find II about the stated axis and divide by the area. The T, for example, has rx=333.3/40=2.89r_x = \sqrt{333.3/40} = 2.89 in. A W shape's table lists rr outright: a W18X50 has rx=7.38r_x = 7.38 in, and 800/14.7\sqrt{800/14.7} agrees.

Checkpoint
1 of 3

A solid round column is 300 mm in diameter. What is its radius of gyration about a centroidal axis?

mm

The least r marks the weak axis

A section has a different rr about each axis, and the smallest is often the one that counts. A slender column buckles the easy way, about the axis its area hugs most closely, as Euler Buckling will show. That axis is the section's weak axis, a term the Handbook doesn't use. For a W shape it's Y-Y: a W18X50 has 1.65 in against 7.38 in.

Don't guess for other sections. Compute rr about both centroidal axes and report the smaller. Remember that the area is the same for both, and only II changes.

Worked Example A hollow rectangle's least r
1 of 3

A hollow rectangular section is 6 in wide and 10 in deep outside, with a centered hole 4 in wide and 8 in deep. Find its least radius of gyration.

Radii don't add, but their squares do

Move the axis to a rectangle's base, and it's tempting to add the offset to the centroidal rr. That doesn't work. What transfers is II, so divide I=Ic+Ad2I = I_c + Ad^2 through by AA:

r2=rc2+d2r^2 = r_c^2 + d^2

The Handbook doesn't print that form, but it's only one line of algebra. Read it as a right triangle: rcr_c and dd are the legs, and rr is the hypotenuse. For a rectangle about its base, that's 0.577h0.577h. Simply adding gives 0.789h0.789h, 37% too high.

h base xc d = 0.500h d = 0.500h rc = 0.289h r = 0.577h r2 = rc2 + d2
A rectangle's r about its base, as a right triangle

The area table saves you the step for each row's own axes. Its column headed (Radius of Gyration)² prints r2r^2, so remember the square root.

Three rows of the (Radius of Gyration)² column
Shaperxc2r_{xc}^2rx2r_x^2Its xx-axis
Rectangleh2/12h^2/12h2/3h^2/3the base
Triangleh2/18h^2/18h2/6h^2/6the base
Circlea2/4a^2/45a2/45a^2/4tangent at the bottom

Adapted from the FE Reference Handbook, Statics area table

Checkpoint
1 of 3

A triangle has a 12 in height. What is its radius of gyration about its base?

in

From a line to a point

So far, every distance has run to a line. A twisting shaft, though, turns about a point, and each bit of area counts by its squared distance ρ\rho from that point. A right triangle splits that distance into xx and yy, so the integral splits too. That gives the polar moment of inertia, printed in the Handbook's Statics chapter under Moment of Inertia:

x y O dA ρ x y
One bit of area, measured from a point
Iz=J=Iy+Ix=∫(x2+y2) dAI_z = J = I_y + I_x = \int (x^2 + y^2)\,dA

The catch is that both axes must be perpendicular and pass through the point. So JJ about a new point means transferring both II values to axes through it, then adding. For a composite, that means tabulating IxI_x and IyI_y separately.

The area table's rectangle row lists J=bh(b2+h2)/12J = bh(b^2 + h^2)/12 without naming the point. It's Ixc+IycI_{xc} + I_{yc}, so it's about the centroid. The same row's Ix=bh3/3I_x = bh^3/3 and Iy=b3h/3I_y = b^3h/3 are about two edges that meet at a corner.

Worked Example A rectangle about its corner
1 of 3

Find the polar moment of inertia of this 4 in by 6 in rectangle about the corner marked OO.

4 in 6 in O
A rectangle and a point at its corner

Round sections, from their diameters

A circle looks the same from every direction, so Ix=IyI_x = I_y and JJ is twice either one. The area table has J=πa4/2J = \pi a^4/2 and, with aa the outer radius and bb the inner, J=π(a4−b4)/2J = \pi(a^4 - b^4)/2. Those are radii, while shafts usually come with diameters, and the Handbook prints no diameter form. So substitute a=D/2a = D/2:

J=πD432J=π(Do4−Di4)32J = \frac{\pi D^4}{32} \qquad J = \frac{\pi\left(D_o^4 - D_i^4\right)}{32}
Where the 16 goes

Put a diameter into πa4/2\pi a^4/2, and you land 16 times too high. For a hollow section, take the fourth powers first and then subtract.

You'll use these in Torsion of Circular Shafts.

Checkpoint
1 of 3

A solid steel shaft is 3 in in diameter. What is its polar moment of inertia about its center?

in⁴

Recap

  • A built-up section is the parallel-axis theorem repeated: add each part's Ic+Ad2I_c + Ad^2, with dd to the section's centroid or the named axis. Parts far out dominate, and a hole subtracts both terms.
  • A W shape is one part, with AA, dWd_W, and II from Table 1-1. A cover plate's dd is dW/2+t/2d_W/2 + t/2.
  • r=I/Ar = \sqrt{I/A} is the distance at which all the area would give the same II, and the least rr marks the weak axis.
  • Radii don't add: r2=rc2+d2r^2 = r_c^2 + d^2, and the area table prints r2r^2.
  • J=Ix+IyJ = I_x + I_y with both axes through the point. For a circle, J=πD4/32J = \pi D^4/32.