Distributed Loads

A load spread along a beam acts like one force at the centroid of its diagram.

Before this Lesson

Snow slides off a high roof and drifts against the wall of the lower one, deep at the wall and thinning to nothing 12 ft out. The beam underneath isn't carrying a force at a point. It's carrying a little force at every point, more of it toward the wall. Everything you know about moments wants an arrow with a line of action, and this drift seems to have thousands of them. You can trade them all for one arrow, and the drift's own shape tells you how big it is and where it goes.

How hard the load presses, foot by foot

Near the wall, each foot of beam holds up a lot of snow. Near the thin edge, very little. So the useful number isn't a force but a force per unit length: how hard the load presses at that spot. That's the load intensity, ww, in lb/ft, kip/ft, N/m, or kN/m. The Handbook's Beams entries use the same letter, and its beam tables write w0w_0 for a triangle's peak.

Plot ww above the beam and you have the load diagram. For the drift, it's a triangle, from 0 at AA to 600 lb/ft at the wall, so halfway along, the beam feels 300 lb/ft. The height is an intensity, not a force, and the little arrows only remind you which way the load pushes.

A B snow drift A B w = 300 lb/ft w0 = 600 lb/ft 6 ft 6 ft
A snow drift and its load diagram

Slivers add up to an area

Take one thin sliver of beam, dxdx wide, a distance xx from the left end. Over so short a stretch, ww barely changes, so the sliver carries one small force, w dxw\,dx: pounds per foot times feet, which is pounds. Now you have an honest arrow. Add up all the slivers for the resultant:

R=∫0Lw dxR = \int_0^L w\,dx

That sum of heights times tiny widths is the area under the load curve. So a load diagram has a strange property: its area comes out in pounds.

Where does it act? Each sliver has a moment about the left end, x(w dx)x(w\,dx), and they all turn the same way. One force can stand in for the lot only if it has the same moment, so:

d=ΣMR=∫0Lx w dx∫0Lw dxd = \frac{\Sigma M}{R} = \frac{\int_0^L x\,w\,dx}{\int_0^L w\,dx}
O w dx w dx x O R C d
Many slivers, then one force

That fraction has a physical picture. Cut the load diagram out of cardboard and balance it flat on a fingertip. A strip of the cardboard, dxdx wide and ww tall, weighs in proportion to w dxw\,dx, just like the sliver of load. Same weights at the same distances, so the balance point sits at the same dd. That balance point, marked CC in the figure, is the area's centroid.

So here's the rule: the resultant of a distributed load equals the area of its load diagram, and it acts through that area's centroid. The Handbook never says this, so it's yours to carry, though its Centroids of Masses, Areas, Lengths, and Volumes entry has the math. With ww in place of f(x)f(x), its A=∫f(x) dxA = \int f(x)\,dx is your RR, and its xc=∫x dA/Ax_c = \int x\,dA/A is your dd. A load diagram is just a shape, and the rest of this Lesson is finding shapes' areas and centroids.

Rectangles and triangles

A uniform load's diagram is a rectangle: R=wLR = wL, with the centroid at the middle by symmetry.

A triangular load's diagram is half the rectangle around it: R=12w0LR = \tfrac12 w_0 L. Its load is piled toward the tall end, so the balance point shifts that way. Run the sliver integral for a load rising as w=w0x/Lw = w_0 x/L:

d=∫0Lx (w0x/L) dx12w0L=w0L2/3w0L/2=2L3d = \frac{\int_0^L x\,(w_0 x/L)\,dx}{\tfrac12 w_0 L} = \frac{w_0 L^2/3}{w_0 L/2} = \frac{2L}{3}

That's two-thirds of the span from the zero end, or a third from the high end. Remember the second one, since it holds whichever way the triangle faces.

Uniform R = wL C w L/2 L/2 Triangular R = w0 L/2 C w0 zero end high end 2L/3 L/3
Where each resultant acts

You won't usually need to derive these. The Handbook's Statics chapter has a table of plane shapes, with no printed title, only columns that begin Figure and Area & Centroid. Call it the area table. Its rectangle row gives A=bhA = bh and xc=b/2x_c = b/2. One right-triangle row, with its origin at the sharp corner, gives A=bh/2A = bh/2 and xc=2b/3x_c = 2b/3, with bb as the span and hh as the peak. Each row measures from the axes in its own sketch, so check where the origin sits.

Worked Example The drift as one force
1 of 3

The drift loads a 12 ft beam, rising from 0 at AA to 600 lb/ft at BB. Replace it with a single resultant, and give its distance from each support.

A B 600 lb/ft 12 ft
The drift's load diagram
Whole body only

The resultant stands in for the load only in the whole body's equilibrium. A 10 ft beam under 100 lb/ft has the same reactions as one with 1,000 lb at midspan. But cut it 3 ft from the end, and the left piece carries only 300 lb, centered 1.5 ft from the end. For a cut, use just the part of the load on one side, as Internal Shear and Moment in Beams does.

Split the diagram into shapes you know

A trapezoid needs no rule of its own, because it's a rectangle with a triangle on top. Draw a horizontal line across the diagram at the height of its low end. Each piece is now a load in its own right, with its own resultant at its own centroid. Swap each for its resultant, and you have a handful of point loads, which you already know how to combine. The area table has a trapezoid row too, but on a load it lies on its side, and splitting is easier to get right.

w1 w1 w2 − w1 L R1 R2 L/2 L/3 R1 = w1 L R2 = (w2 − w1)L/2
A trapezoid as a rectangle and a triangle

Any mix goes the same way. A point load joins the list as it is, and a load that changes shape partway along gets one piece per stretch. Every load here pushes down, so about the left end all the moments turn the same way, and you can add sizes. (An upward load would subtract from both sums.) Centroids of Areas takes this same sum to composite areas in general.

Worked Example A trapezoidal load
1 of 3

Find the single equivalent force for this load and its distance from AA.

A B 200 lb/ft 500 lb/ft 10 ft
A trapezoidal load on a 10 ft beam

Working backward to the load

The exam also hands you the resultant, or where it acts, and asks for the load that made it. Nothing new is needed, only the same facts with an unknown left in. Write each piece's size and moment with the unknown still in them. For a stated resultant, set the total force equal to it. For a stated location, set ΣM=Rd\Sigma M = Rd, which keeps the unknown out of the denominator.

Worked Example A peak that centers the resultant
1 of 4

This beam's triangular load has an unknown peak, w0w_0. What peak puts the single resultant at midspan, so that the two supports share the load equally?

A B w0 3,000 lb 2 ft 10 ft
A beam with an unknown peak intensity

A load given as a function

Sometimes the curve comes as an equation, such as w=3x2w = 3x^2. You can go straight back to the slivers, and that works for any w(x)w(x):

R=∫w dxd=∫x w dxRR = \int w\,dx \qquad d = \frac{\int x\,w\,dx}{R}

Your calculator's numerical integration can run both integrals as a quick check. Or, if the curve is a parabola, read it from the area table. A parabola makes two load shapes, and you tell them apart by where the curve goes flat.

A curve that leaves the beam flat and bends up to its peak sags below a triangle's straight line, so there's less load, crowded toward the high end. That's the row labeled nth degree parabola, y=(h/bn)xny = (h/b^n)x^n, with n=2n = 2. It prints A=bh/(n+1)A = bh/(n + 1) and xc=(n+1)b/(n+2)x_c = (n + 1)b/(n + 2), from the zero end, which give bh/3bh/3 and 3b/43b/4.

A curve that climbs fast and goes flat at its peak bulges above that line. That's the row labeled half a parabola, turned on its side: its aa is your peak, its bb is your span, and A=2ab/3A = 2ab/3. Its yc=3b/8y_c = 3b/8 is your location, measured from the high end. Its xc=3a/5x_c = 3a/5 runs up and down here, not along the beam.

Flat at the zero end R = w0 L/3 w0 L/4 Flat at the peak R = 2w0 L/3 w0 3L/8
Two parabolic loads, told apart by where the curve goes flat

Adapted from the FE Reference Handbook, Statics area table

Each dashed rectangle is LL by w0w_0. Flip one shape into the empty part of the other's rectangle and it fits exactly, which is why their areas are a third and two-thirds of it.

Load shapes, with each location measured from the high end
Load shapeResultantLocation
UniformwLwLL/2L/2
Trianglew0L/2w_0 L/2L/3L/3
Parabola, flat at the zero endw0L/3w_0 L/3L/4L/4
Parabola, flat at the peak2w0L/32w_0 L/33L/83L/8

Adapted from the FE Reference Handbook, Statics area table

A symmetric hump, zero at both ends with its peak at midspan, is two of that last shape back to back: R=2w0L/3R = 2w_0 L/3, at the middle.

Worked Example A parabolic load, two ways
1 of 3

A bar runs along the x-axis from x=0x = 0 to x=4 mx = 4\ \text{m} and carries w=3x2w = 3x^2 kN/m, with xx in meters. Find the resultant and where it acts.

Recap

  • ww is force per unit length. For the whole body's equilibrium, the resultant equals the area of the load diagram and acts through its centroid. The Handbook doesn't state this, but its area table has the shapes.
  • Uniform: wLwL at the middle. Triangle: 12w0L\tfrac12 w_0 L, a third of the span from the high end. Match length units first.
  • Split trapezoids and mixes into rectangles and triangles, each with its own resultant and centroid, add any point loads, and use d=ΣM/Rd = \Sigma M/R.
  • To work backward, leave the unknown in, then set the total force or ΣM=Rd\Sigma M = Rd.
  • For w(x)w(x), integrate ww and xwxw. Or, for a parabola, read the table: flat at the zero end or flat at the peak.