Free-Body Diagrams and Supports

A support pushes back only in the directions it stops the body from moving.

Lay a ruler flat on a desk. Slide it left and right. Slide it toward you and away. Spin it. Now look for a fourth way to move it without lifting it off the desk. There isn't one. Push a thumbtack through one end, and the sliding stops, though it still spins. Clamp that end down, and the spinning stops too. Those three motions, and which of them a support takes away, decide what a free-body diagram shows at that support.

Cut the body free

In Equilibrium of a Particle, you isolated a ring, drew what pulled on it, and summed to zero. A beam gets the same routine: isolate, draw, sum to zero. What's new is that a beam has length, so where a force acts now matters, and it's held by more than cables.

The drawing is called a free-body diagram. Draw the body alone, floating, with its supports gone. Then put back, as a force, everything that was touching it, and add gravity. Here's a boom on a wall, before and after.

30° 500 lb A D B C Uniform, 200 lb Free-body diagram 30° Ax Ay T 200 lb 500 lb A D B 5 ft 2 ft 3 ft
A boom on a wall, and the same boom cut free

Three things touched the boom. The pin at A becomes two arrows, for reasons coming up. The cable at B becomes a tension pulling away along the cable, as it did on the ring. The sign's hanger at D pulls down with 500 lb. Gravity adds the boom's 200 lb, at its middle because it's uniform, and the dimensions go on, since the moment equations will need them. The Handbook names the free-body diagram once, under Plane Truss: Method of Sections, and never says how to draw one, so this is yours to carry in.

A free-body diagram shows only external forces, what the outside world does to the body. The boom is also full of internal forces, each slice of steel pulling on the next. Those come in equal and opposite pairs, so they cancel and stay off the diagram. What counts as internal depends on where you draw the line. Draw it around the boom alone, and the cable's tension is external. Draw it around the boom and cable together, and that tension is internal, and the wall's pull at C takes its place.

Three motions, and what each support stops

Back to the ruler. A body in a plane can slide in x, slide in y, or rotate, and that's all. So ask one question of any support: which of these does it stop? To stop a slide, it has to push or pull in that direction, so it supplies a force. To stop rotation, it has to twist back, so it supplies a moment. A motion it leaves free, it can't resist at all.

Free 3 ways to move slide x rotate slide y Roller 2 ways to move slide x rotate Ay A Pin 1 way to move rotate Ax Ay A Fixed No way to move MA Ax Ay A
Each support takes away motions and gives back reactions

A roller lets the body roll along a surface and turn, and stops it only from moving into the surface: one force, normal to the surface. A long bridge often rests on rollers at one end, so it can grow in the summer heat without shoving its supports apart. A smooth surface works the same way, as with a cylinder in a smooth groove: one push, normal to the contact. Tilt the surface, and the force tilts with it.

A cable stops the body only from moving away along it, so it supplies one force, the tension TT, pulling away from the body. A link, a short straight bar pinned at both ends with nothing else loading it, stops motion along its own line. It supplies one force along that line, a push or a pull, like a strut. Why the force lines up with the bar waits for Trusses: Method of Joints.

A pin, or hinge, holds one point of the body in place and lets it turn, like a door on its hinges. It stops both slides and no rotation. Its force has to point somewhere, but you don't know where yet, so it goes on the diagram as two components, AxA_x and AyA_y. Both go on every time, even when nothing seems to push sideways. With no horizontal load, AxA_x just comes out zero. The diagram shows what a support can do, not what it turns out to do.

A fixed support, like a beam built into a wall, stops all three. It supplies AxA_x, AyA_y, and a moment, MAM_A, drawn as a curved arrow. A load out on the beam twists the built-in end, and MAM_A is the couple that twists back. Leave it off, and nothing on the diagram keeps the beam from turning.

Support On the diagram Roller A Ay A Smooth surface A NA A Cable A T A Link A FA A Pin A Ax Ay A Fixed support A MA Ax Ay A
The supports, and what each one becomes on a free-body diagram

Reactions are named after the point where they act, so a pin at A gives AxA_x and AyA_y. The Handbook prints no table of supports. Its beam tables just draw them, unlabeled: a small triangle for a pin, a circle for a roller, and a hatched wall for a fixed end, the same symbols used here.

Checkpoint
1 of 3

A steel sign post is cast into a concrete footing. What does the footing provide at the post's base?

A.
One vertical force
B.
Two force components
C.
A vertical force and a moment, with no horizontal force
D.
Two force components and a moment
What each support stops and provides
SupportStopsProvidesUnknowns
RollerInto the surfaceOne normal force1
Smooth surfaceInto the surfaceOne normal push1
CableAway along itOne pull along it1
LinkAlong itOne push or pull along it1
PinBoth slidesTwo force components2
Fixed supportSlides and rotationTwo components and a moment3

Draw it the same way every time

Every correct diagram comes from the same short routine:

  1. Draw the body alone, with its dimensions.
  2. Add what's given: applied loads where they act, and the body's weight at its center.
  3. Walk around the edge. Wherever something touches the body, draw what that support provides.
  4. Label each unknown, and give it a sense.

The walk is what keeps forces from going missing. If a problem gives a mass instead of a weight, the Handbook's Concept of Weight turns it into W=mgW = mg. If it gives neither, the body is taken as weightless, and there's no arrow.

Worked Example A bar on a pin and an inclined roller
1 of 3

A uniform 10 ft bar AB weighs 80 lb. It's pinned at A, sits on a roller on a 30° incline at B, and carries a 400 lb load 7 ft from A. Draw its free-body diagram.

30° 7 ft 3 ft 400 lb A B Uniform, 80 lb
A bar on a pin and a roller

Finding the mistake

Exam questions also hand you a finished diagram and ask what's wrong with it. Take the same walk around the body, and ask:

  • Does each support have all of its reactions, and no extras?
  • Does each cable pull away from the body?
  • Is each smooth contact's force normal to the surface?
  • Is every given load and weight there?
  • Is anything there that shouldn't be, such as an internal force or friction on a smooth surface?
Checkpoint
1 of 3
6 kN 4 kN A B Proposed diagram 6 kN 4 kN Ay By A B
A beam on a pin and a roller, and a proposed diagram

What's wrong with the proposed free-body diagram?

A.
Nothing, because all of the loads are vertical
B.
The pin's horizontal reaction is missing
C.
The roller needs a horizontal reaction
D.
The reactions at A and B should point down

Pick a sense, and let the sign correct you

You often can't tell which way an unknown points until you've solved for it, so pick a sense, draw it, and move on. On the worked example's bar, with its roller on the 30° incline, suppose you'd drawn AxA_x to the left. The equations, which Beam Reactions runs, would return Ax=−185 lbA_x = -185\ \text{lb}. That's no mistake. The diagram was right except for one arrow, and the answer says the pin pushes 185 lb to the right. The size is good, and if you carry the minus sign into later equations, they come out right too. The Handbook doesn't mention this.

That freedom applies to pins, links, and fixed supports. A cable can only pull, and a roller or smooth surface can only push, so draw those the way they really act. If one of them comes out negative, the arrow isn't backward. The cable has gone slack, or the body has left the surface.

Three motions, three equations

The Handbook's Equilibrium Requirements, under Systems of Forces, prints equilibrium as two vector equations, ΣFn=0\Sigma \mathbf{F}_n = 0 and ΣMn=0\Sigma \mathbf{M}_n = 0. For one body in a plane, they become three:

ΣFx=0ΣFy=0ΣM=0\Sigma F_x = 0 \qquad \Sigma F_y = 0 \qquad \Sigma M = 0

There's one for each motion. Two stop the body sliding, and one stops it turning. That count is why one free body can settle at most three unknowns. Once a body can't slide or turn, there's nothing left to say. The ring had only two equations because its forces all meet at one point, so about that point they have no arm and the moment equation is empty.

Checkpoint
1 of 2

Which statements about free-body diagrams are true?

A.
Internal forces between parts of the body are left off.
B.
A pin's horizontal reaction is left off when no horizontal load acts.
C.
A negative pin component means it acts opposite to the sense drawn.
D.
A moment equation about a second point adds a fourth independent equation.
E.
One planar free body gives at most three independent equations.
F.
A negative answer means the diagram has to be redrawn and re-solved.

Recap

  • Isolate, draw, sum to zero. A free-body diagram is the body alone, with every external force on it, including any given weight. Internal forces stay off.
  • A support pushes back only where it stops motion. A roller, smooth surface, cable, or link gives one force, a pin gives AxA_x and AyA_y, and a fixed support adds MAM_A.
  • Cables pull away from the body, and smooth contacts push normal to the surface.
  • A pin keeps both components even with no horizontal load. Assume a sense you don't know, and read a negative answer as the opposite sense.
  • Three ways to move in a plane means at most three independent equations per free body.