Beam Reactions

Take moments about one support, and the other reaction falls out in one line.

Two sawhorses stand 10 ft apart. Across them lies a 14 ft plank weighing 80 lb, with its left end on one sawhorse and its last 4 ft sticking out past the other. You weigh 160 lb, and what you need to reach is out past the end. Everybody knows that if you walk far enough, the far end comes up and you come down. How far is far enough? Take a guess now, and hold on to it.

A B 80 lb plank 160 lb 10 ft 4 ft
A plank, two sawhorses, and you

An equation that can't see A

Start somewhere safe, standing between the sawhorses, 5 ft from AA. Draw the plank free. Each sawhorse pushes up and can't pull down, so each gets one arrow: AyA_y and ByB_y. The plank's 80 lb acts at its middle, 7 ft from AA.

That's two unknowns, and summing forces won't separate them. ΣFy=0\Sigma F_y = 0 says Ay+By=240 lbA_y + B_y = 240\ \text{lb}, which is true and leaves you stuck.

So take moments about AA instead. The line of AyA_y runs right through AA, so its arm is zero, and so is its moment, however big it turns out to be. The equation can't see it. Only one unknown is left:

ΣMA=By(10)−160(5)−80(7)=0⇒By=136 lb\Sigma M_A = B_y(10) - 160(5) - 80(7) = 0 \quad\Rightarrow\quad B_y = 136\ \text{lb}

ByB_y pushes up to the right of AA, which turns the plank counterclockwise. Both weights push down to the right of AA, which turns it clockwise. Now ΣFy=0\Sigma F_y = 0 finishes the job: Ay=240−136=104 lbA_y = 240 - 136 = 104\ \text{lb}. Or play the same trick about BB, where ByB_y disappears instead, and you have a check:

ΣMB=−Ay(10)+160(5)+80(3)=0⇒Ay=104 lb\Sigma M_B = -A_y(10) + 160(5) + 80(3) = 0 \quad\Rightarrow\quad A_y = 104\ \text{lb}
Moments about A 160 lb 80 lb 5 ft 7 ft 10 ft A B Ay no arm By Moments about B 160 lb 80 lb 3 ft 5 ft 10 ft A B By no arm Ay
The same plank, seen from each support

That's the move for nearly every beam on the exam. The Handbook's Equilibrium Requirements, under Systems of Forces, prints ΣFn=0\Sigma \mathbf{F}_n = 0 and ΣMn=0\Sigma \mathbf{M}_n = 0 but not where to take the moments, and that choice is most of the skill. Its beam tables print no reactions either, so you'll work these out yourself.

Pins, overhangs, and spread-out loads

A real beam adds a few details, and none of them changes the move. A beam with a pin at one end and a roller at the other is simply supported, or a simple beam, and if it runs on past a support, it's overhanging. The pin at AA brings AxA_x along with AyA_y, but both act through AA, so moments about AA can't see either one. A distributed load goes in as its resultant. And a load past a support turns the beam the other way about that support, so its term takes the opposite sign. Here's the routine:

  1. Draw the free-body diagram, with each distributed load swapped for its resultant.
  2. Take moments about one support to get the reaction at the other.
  3. Use ΣFy=0\Sigma F_y = 0 for the first support's vertical reaction, and moments about the other support to check it.
  4. Use ΣFx=0\Sigma F_x = 0 for the pin's horizontal reaction.

A load at a slant gets resolved first. Its vertical part goes through the routine like any other load. Its horizontal part, acting along the beam, passes through both supports with no arm, so it never enters a moment equation. It goes entirely to the pin, because a roller on a level surface can't push sideways.

Worked Example An overhanging beam
1 of 3

Find the reactions at AA and BB.

300 lb/ft 1,200 lb A B C 10 ft 3 ft
A beam with a uniform load and an overhang

Walk along the plank

Back on the plank, and this time keep walking. Let xx be your distance from AA, and leave it in the equation:

ΣMA=By(10)−160x−80(7)=0⇒By=56+16x\Sigma M_A = B_y(10) - 160x - 80(7) = 0 \quad\Rightarrow\quad B_y = 56 + 16x

So Ay=240−By=184−16xA_y = 240 - B_y = 184 - 16x. Plot both.

−50 0 50 100 150 200 250 300 0 2 4 6 8 10 12 14 x, your distance from A (ft) Reaction (lb) A B Ay By Ay + By = 240 lb lift-off, x = 11.5 ft
The sawhorse reactions as you walk the plank

Both are straight lines, because your moment about a support grows in step with your distance from it. Each foot you walk moves the same 16 lb off AA and onto BB: your 160 lb over the 10 ft span. And the two always add to 240 lb, since ΣFy\Sigma F_y doesn't care where you stand. Any load on any span behaves this way, shifting P/LP/L per foot of travel, which is the idea that Influence Lines builds on.

Now look where AyA_y hits zero: 11.5 ft from AA, only 1.5 ft past BB. How was your guess? The other 2.5 ft of that overhang is there to fool you. A sawhorse can only push, so at zero the plank is touching it with no force at all, and it's about to rise. That's lift-off. Past that, the line goes negative, which would take a sawhorse pulling down on a plank it isn't tied to. That can't happen, so the dashed part never does: the plank has already swung down about BB. So lift-off isn't a negative reaction. It's the load or position at which the reaction reaches zero.

You don't need the whole line to find it. Set the lifting reaction to zero, then take moments about the other support. No unknown reactions are left in that equation, only the loads on one side of the pivot against the loads on the other. The Handbook doesn't mention lift-off, so this one's yours to carry.

Worked Example The same limit, without the graph
1 of 3

The same plank, and the same you. With no graph and no formula for AyA_y, how far past BB can you stand before the plank lifts off AA?

A B 80 lb plank 160 lb 10 ft 4 ft
The plank again

Trade the load for a couple

Now take a load off a beam and apply a pure twist instead: a counterclockwise couple M0M_0, the Handbook's symbol in its beam tables, somewhere on a span LL. A couple has zero resultant, so ΣFy=0\Sigma F_y = 0 says Ay+By=0A_y + B_y = 0. The reactions are equal and opposite, which makes them a couple of their own, and only a couple can balance a couple. About AA, ByB_y has the arm LL, and M0M_0 counts with no arm at all:

ΣMA=ByL+M0=0⇒By=−M0LAy=+M0L\Sigma M_A = B_y L + M_0 = 0 \quad\Rightarrow\quad B_y = -\frac{M_0}{L} \qquad A_y = +\frac{M_0}{L}

Look at what's missing from that answer: where the couple sits. A couple has the same moment about every point, so the beam can't tell.

A B M0/L M0/L M0 A B M0/L M0/L M0 A B M0/L M0/L M0 L
One couple in three places, with the same reactions

For the sense, picture the beam turning the way the couple pushes it. Counterclockwise lifts the right end and presses the left one down, so BB has to hold down and AA has to push up. When other loads act too, the reactions add, so the couple just moves M0/LM_0/L from one reaction to the other.

One honest note about that pull at BB. A beam just resting on a roller can't get it, as the plank showed. By convention, which the Handbook doesn't spell out, a beam problem treats its roller as able to hold down as well as push up, unless the problem says the beam rests on it or asks about lift-off.

Checkpoint
1 of 3

The same load PP can sit at any of these four places on a beam with a pin at AA and a roller at BB. Where is the vertical reaction at AA the largest?

A.
P A B
B.
P A B
C.
P A B
D.
P A B

One support, three unknowns

A cantilever has only one support, so there's no other support to take moments about. There's also no need. All three unknowns sit at the wall, and each equation catches exactly one: ΣFx=0\Sigma F_x = 0 gives AxA_x, ΣFy=0\Sigma F_y = 0 gives AyA_y, and ΣMA=0\Sigma M_A = 0 gives MAM_A.

Moments about AA still can't see AxA_x or AyA_y. MAM_A is different. It's a couple, and a couple counts the same about every point, so it's the one reaction a moment equation always sees. Physically, it's the wall twisting back against every load out on the beam. Leave it off, and the beam would swing down like a door on a hinge.

Worked Example A cantilever with an inclined load
1 of 4

Find the reaction components and the moment at the wall.

300 lb/ft A B 1,000 lb 3 4 5 8 ft
A cantilever with two loads

Recap

  • A moment equation about a support can't see the forces acting there. Take moments about one support to get the other reaction in one line, use ΣFy=0\Sigma F_y = 0 for the last one, and check with moments about the other support.
  • Swap each distributed load for its resultant first. A load past a support turns the beam the other way about it, and a slanted load's horizontal part goes to the pin, never the roller.
  • Lift-off is the point where a reaction reaches zero, not where it goes negative. Set it to zero and take moments about the other support.
  • As a load moves, each foot shifts P/LP/L from one reaction to the other and their sum holds. A couple gets M0/LM_0/L up and M0/LM_0/L down, wherever it sits.
  • A cantilever's three unknowns all sit at the wall, one per equation. MAM_A is the wall twisting back, and a moving load changes only it.