Back

Structural Engineering

  • Topic 11
  • 17 Lessons

Overview

Every question in this topic sits somewhere on one chain. A load lands on a structure and travels through its members to the ground. On the way, it asks something of each member, a moment, a shear, a push or a pull, and that's the demand. The member answers with its capacity, and it has a separate capacity for each way it can fail. The weakest of those is the one that governs.

So the whole topic runs on one habit: follow the load to find the demand, then check the demand against the capacity of each way the member can fail. Placing an exam question on that chain is most of the work. One check comes before the analysis: the structure has to be able to stand.

Load dead, live, snow, wind Load path slab → beam → girder → column → footing Can it stand? no unstable: nothing to analyze yes Demand Mu, Vu, Pu in each member φRn ≥ Ru Capacity φRn for each way it can fail Governing limit state yielding, rupture, buckling: the smallest governs
One chain, from the load to the limit state that governs
The stability check comes before the analysis, because a structure that can move has no demand to find.

Loads travel a path to the ground. Set a filing cabinet on the third floor of an office building and follow its weight. The slab carries it to the nearest beams. Each beam hands its share to the girders or columns at its ends, the columns carry it down floor by floor, and a footing spreads it into the soil. Each member's share of the floor stops halfway to its neighbors, so every square foot of floor is counted exactly once on its way down. Loads and Load Combinations sorts out which loads there are and how they combine, and Tributary Areas and Load Paths follows them member by member.

Analysis finds the demand, and design checks it against capacity. When the cabinet's weight reaches a beam, it bends it, so the beam needs moment strength near midspan and shear strength near its ends. Analysis turns loads into those numbers, mostly by statics, starting in Design Moments and Shears. Deflections are part of it too: they unlock the beams statics alone can't solve, and they're checked against limits of their own. Influence lines show where a moving load does the most harm. Then design asks whether the member can take it. Every design check in the topic has the same shape, demand versus capacity, and in load and resistance factor design (LRFD) it reads

ϕRn≥Ru\phi R_n \ge R_u

On the right is the demand, built from loads marked up for how uncertain they are. On the left is the capacity, the member's strength marked down a little for the same reason. Each design Lesson writes it with MM, VV, or PP in place of RR.

Each member fails in particular ways, and one of them governs. A steel plate bolted at its ends can stretch along its whole length until it's too long to be any use, or it can tear across its bolt holes. A long column doesn't crush at all. It bows out sideways, at a load set by its stiffness, long before the steel runs out of strength. A steel beam can yield through its depth or twist sideways, and a concrete beam can crack on a diagonal near its support. Each is a limit state with its own capacity, and the smallest capacity is the one that counts. Often, which one comes first is the whole question.

Yielding P P Rupture P P stretch stretches along its whole length tears across its bolt holes Buckling P bows out sideways
Three ways a steel member can fail
A bolted plate in tension can yield or rupture. A slender column in compression buckles.

The Handbook's steel section names its limit states as it goes: Yielding and Rupture for tension members, Yielding and Lateral-Torsional Buckling for beams. The column Lessons and the steel and concrete design Lessons take these one member at a time, and each ends at demand versus capacity.

Before analyzing anything, make sure it can stand. Pin three sticks into a goalpost shape, with a pin at each top corner and at each foot, and push the top sideways. It leans over into a parallelogram. Every stick is fine; the frame just can't push back, and no moment or shear means anything for a structure that moves. So you count first, the unknown forces against the equations statics offers. Too few, and it's unstable. Just enough, and statics solves it. More, and the extra restraint takes deflections to solve. Then you look, because supports can pass the count and still line up so that something moves. The Handbook's Stability, Determinacy, and Classification of Structures does the counting and closes with the same warning: stability also requires an appropriate arrangement of members and reaction components. Determinacy and Stability teaches both halves.

In the Handbook, most of this topic lives in the Civil chapter, under Structural Analysis and Structural Design. The beam deflection tables and Euler's formula for the buckling load sit back in Mechanics of Materials.

Try placing a few questions on the chain. For each one, pick the idea it turns on.

Checkpoint
1 of 4

A long, thin steel rod braces a radio tower. When the wind reverses, the rod is squeezed instead of stretched. The question asks what sets how much compression it can take.

A.
Follow the load path
B.
Compare demand with capacity
C.
Find the limit state that governs
D.
Check stability before analyzing

Lessons

  1. 1Loads and Load CombinationsDesign for the worst plausible mix of loads, each scaled by how uncertain it is.
  2. 2Tributary Areas and Load PathsEvery square foot of floor is carried by exactly one beam, and every beam by a girder or a column.
  3. 3Design Moments and ShearsFactor the loads first, and the beam diagrams give the demand.
  4. 4Determinacy and StabilityCount first, then look: a structure can have enough supports and still collapse.
  5. 5Beam Deflection by SuperpositionThe deflections from separate loads simply add.
  6. 6Beams with One RedundantRemove the extra support, then push the beam back to where that support held it.
  7. 7Influence LinesAn influence line shows where to park the truck to do the most damage.
  8. 8Truss Deflection by Virtual WorkPut an imaginary unit load where you want the deflection, and it tells you which members matter.
  9. 9Euler BucklingA long column doesn't crush; it bows sideways at a load set by stiffness alone.
  10. 10Slenderness and the Governing AxisA column buckles about whichever axis gives the largest KL/rKL/r.
  11. 11Steel Beam Flexural StrengthA steel beam keeps carrying load after it starts to yield, until the whole section has yielded.
  12. 12Selecting Steel BeamsPick the lightest beam that's strong enough, then make sure it isn't too bouncy.
  13. 13Steel Column StrengthReal columns buckle sooner than Euler predicts, and the AISC curve accounts for it.
  14. 14Steel Tension MembersA bolted plate is only as strong as its weakest path between the holes.
  15. 15Reinforced Concrete Beam StrengthConcrete takes the squeeze, steel takes the pull, and together they form a couple.
  16. 16Designing Reinforced Concrete BeamsRun the stress block backward to find the steel a beam needs.
  17. 17Shear in Reinforced Concrete BeamsConcrete cracks diagonally near the supports, and stirrups stitch the cracks closed.